Search results for "Steel"

[The effect of instrumentation on original apical foramen shape using steel vs niti rotatory: computerized analysis]

2002

BACKGROUND. A fundamental requirement to obtain a correct endodontic preparation depends on the respect, during cleaning and shaping, of the original morphology of the apical foramen, (AF), so that the filling material will form a complete seal. METHODS. In our previous studies, in order to verify if this presumption was respected using rotary NiTi instruments with cutting tip, we instrumented extracted teeth characterised by a different degree of root curvatures. Using a standardized system to replace the sample, the original shape of the apical foramen of each tooth was recorded using a computerised technique and then compared to the shape after instrumentation. The data showed difference…

Torsional shear strength and elastic properties of adhesively bonded glass-to-steel components

2020

Nowadays glass is widely used in building applications and coupled to steel through adhesive joining. Reliable mechanical characterization of these joints is necessary to design and predict the final structure performance.In this framework, the aim of this paper is to measure the pure shear strength and elastic modulus for design and modelling of adhesive joined glass-to-steel structures.Torsional shear strength and elastic properties of an adhesively bonded glass-to-steel component were measured on several joined steel-to-steel and steel-to-glass samples.An epoxy resin-based adhesive was used as joining material for AISI304 steel and soda-lime glass.The same steel and adhesive were used to…

Wear mechanisms and residual stresses in alumina-based laminated cutting tools

2005

Abstract The outstanding performances of the Al2O3 cutting tools in terms of potential cutting speed can lead to substantial economies in the machining of metallic materials. Nevertheless, their widespread use is limited by some drawbacks such as the tendency to edge chipping and to the propagation of microcracks, which can lead to premature failures. These shortcomings are due to the intrinsic low toughness of the ceramic material, which is in turn related to its characteristics non-metallic bonds. A well-recognised method of increasing the toughness of brittle materials is the introduction of surface compressive stresses, which can be obtained through a suitable lamination geometry of the…

Televisión: lo cotidiano y lo autorreferencial. Los genéricos del telefilm

1986

En conclusión, hemos analizado algunos de los mecanismos de autorreferencialidad que caracterizan al discurso de telefilm a partir de sus genéricos, trabajo de diferenciación en el modelo hollywoodense que sirve de base al montaje de dichos espacios y aquí un rasgo todavía más de neutralización. Ello se ha materializado, en formas diversas, en una primera autorreferencialidad del episodio hacia sí mismo; en segundo, una autorreferencialidad que incluye a todas las demás y les imprime su sello tan indefectible como autoritario. Pues los telefilms están continuamente segmentados en su interior por espacios vacíos que sólo la publicidad puede llenar. Incluso podría afirmarse que el telefilm só…

Steel fibre and transverse reinforcement effects on the behaviour of high strength concrete beams

2012

An experimental program was carried out to investigate the influence of fibre reinforcement on the mechanical behaviour of high strength reinforced concrete beams. Eighteen beams, loaded in fourpoint bending tests, were examined by applying monotonically increasing controlled displacements and recording the response in terms of load-deflection curves up to failure. The major test variables were the volume fraction of steel fibres and the transverse steel amount for two different values of shear span. The contribution of the stirrups to the shear strength was derived from the deformations of their vertical legs, measured by means of strain gauges. The structural response of the tested beams …

Model-assisted ultrasonic calibration using intentionally embedded defects for in-process weld inspection

2021

Abstract Automated in-process Non-Destructive Testing (NDT) systems are rapidly gaining traction within the manufacturing industry as they reduce manufacturing time and costs. When considering calibration and verification of such systems, creating defects of known geometry and nature during the deposition of a weld can: (I) help examine the capability of the automated system to detect and characterise defects, (II) be used to form a database of signals associated with different defect types to train intelligent defect classification algorithms, and (III) act as a basis for in-process gain calibration during weld inspection at high temperatures, where the ultrasound beam can be skewed as a r…

Comportamento di una passerella pedonale strallata nei confronti delle azioni del vento

2007

The wind behaviour of a stayed footbridge has been analyzed. In order to avoid aeroelastic phenomena, an experimental campaign on a 1:15 scale model has been realized at the boundary-layer wind-tunnel of the Milan Polytechnic. The aerodynamic characterization of the structure has allowed to direct the project towards the choice of non-solid barriers, but with a medium porosity, by avoiding possible problems that can lead to ultimate limit state condi-tions of the structure (e.g., flutter or vortex shedding). In this way the quantitative effect of barriers has been estimated deducing reliable values not only for the alongwind forces, but also for the crosswind and torsional actions.

On the mechanisms involved in the tensile strength of a dissimilar Ti6Al4V/316L laser welded assembly

2021

International audience; The aim of the present work is to analyze the thermomechanical behavior of dissimilar laser seams by means of FE modeling. The case of a Ti6Al4V/316L assembly with vanadium insert was considered. Effective mechanical properties of the main materials and cords were first estimated from NHT measurements. Modeling of the double pass laser welding process was performed first by considering shrinking of the two weld seams during manufacturing, to get the residual stress state in the welded assembly. Modeling of the tensile test was performed in a second step to study the assembly behavior during loading. In these modeling results, the mesh was the cross-section of the mic…

Structural design of Fiumara d'Arte land art works

2012

Strengthening of Masonry Columns with BFRCM or with Steel Wires: An Experimental Study

2016

Nowadays, innovative materials are more frequently adopted for strengthening historical constructions and masonry structures. The target of these techniques is to improve the structural efficiency with retrofitting methods while having a reduced aesthetical impact. In particular, the use of basalt fiber together with a cementitious matrix emerges as a new technique. This kind of fiber is obtained by basalt rock without other components, and consequently it could be considered a natural material, compatible with masonry. Another innovative technique for strengthening masonry columns consists of applying steel wires in the correspondence of mortar joints. Both techniques have been recently pr…