Search results for "Styrene"
showing 10 items of 561 documents
Diffusion of spherical micronetworks in polymer diluent systems and melts studied by dynamic light scattering techniques
1994
Spherical polystyrene (PS) micronetworks can be prepared in microemulsion with bulk radii of 5–60 nm and different cross-linking densities. The diffusion of these PS spheres has been studied in polymer diluent systems ranging from dilute solutions to plasticized melts by using forced Rayleigh scattering and photon correlation spectroscopy. On increasing the PS concentration, a colloid glass transition is observed at a volume fraction ΦC ≈ 0.64 of the swollen spheres. At higher concentration inside the “colloid glass” state the sphere diffusion is slowed down and becomes very complex but can be observed up to the limit of a melt of collapsed spheres.
Mechanical behavior and structure of single beads of homogeneous and macroporous styrene–divinylbenzene copolymers
1982
The stress–stain and ultimate behavior in compression of homogeneous and macroporous beads of styrene–divinylbenzene copolymers has been investigated in the dry state or in equilibrium with toluene, acetone, methanol, and water. The penetration modulus A indicates sensitively the transition from the glassy into the rubbery state induced by an increase in temperature or swelling. For macroporous copolymers, A of the glassy polymers is mainly determined by the porosity P, while in the rubbery region it primarily depends on the matrix structure (degree of crosslinking and concentration and composition of the diluent). The high value of the slope s of the A vs. P dependence (s ∼ −3) for macropo…
Controlled Synthesis of Linear Polymers with Highly Branched Side Chains by “Hypergrafting”: Poly(4-hydroxy styrene)-graft-hyperbranched Polyglycerol
2012
Linear polymers with hyperbranched side chains are unusual macromolecular structures due to their high number of functional groups in the side chains as well as their potential cylindrical conformation in bulk or solution. In a three-step synthesis combining anionic and oxy-anionic polymerization, hyperbranched polyglycerol was “hypergrafted” from linear poly(4-hydroxy styrene) macroinitiators to yield poly(4-hydroxy styrene)-graft-hyperbranched polyglycerol. Successful grafting with control over molecular weight (10–31 kg·mol–1) and low PDIs (<1.4) was shown by various characterization techniques. All polymers have a high side chain density, due to rapid transfer of the initiating function…
Ferroelectric block copolymers
1997
A block copolymer consisting of polystyrene and a side chain ferroelectric liquid crystalline polymer was synthesized using polymer analogous chemistry on a monodisperse poly(styrene-b-isoprene). Composition was adjusted to give lamellar microstructure after addition of the mesogenic side groups. If placed in an LC cell without orientation of domains, no ferroelectric response was observed. After shearing the thin film, presumably due to alignment of lamellae, a bistable ferroelectric switching could be detected.
Polymer-polymer interaction parameters in solvent/polymer/polymer ternary systems
1981
Abstract Empirical equations defining the relationships between b23 and χ23 interaction parameters for the ternary systems toluene (1)/poly(dimethylsiloxane), PDMS, (2)/polystyrene, PS, (3) and benzene (1)/PDMS(2)/PS(3) have been determined. The dependences of both interaction parameters on the mean molecular weights of the macromolecular components have also been studied. A single dependence of b23 (or χ23) upon the mean molecular weight is found when both polymeric components have intermediate to high molecular weights. However, that single dependence is not found when the molecular size of polymer (2) is low.
Living Polymer Chains with Predictable Molecular Weight and Dispersity via Carbanionic Polymerization in Continuous Flow: Mixing Rate as a Key Parame…
2016
Aiming at systematic variation of the parameter dispersity, Đ (or “polydispersity”), living polymers with predictable dispersity (Đ = 1.15–2.20) and controlled molecular weights (Mn = 3200–18 500 g mol–1) were prepared via carbanionic polymerization. The approach relies on a continuous flow reactor equipped with a tangential four-way jet micromixing device. By varying the total flow rate, the mixing efficiency of the initiator (sec-BuLi) and the corresponding vinyl monomers is controlled, resulting in polymers with predefined dispersity, while the number-average molecular weight, Mn, is kept constant. In this manner living polystyrene (PS), poly(p-methylstyrene) (PpMeS), and poly(2-vinylpyr…
Nanoscale Blends between Immiscible Polymers via Simultaneous Non-Interfering Polymerisation
2005
An important topic in polymer science seeks to improve the performances of polymer blends using nanoscale phase segregation. Here, blends between polystyrene and polycaprolactone are realised by a chemical route. The non-interfering character of the radical polymerisation of styrene and the lanthanide halide initiated ring-opening polymerisation of caprolactone is assessed. The molecular weights range from 2 000 to 3 500 for polycaprolactone and up to 140 000 for polystyrene, with reasonable polydispersity indexes. From calorimetry measurements, it is shown that polystyrene and low molecular weight polycaprolactone are immiscible. The morphology of the blends between the two immiscible poly…
Functional Diblock Copolymers for the Integration of Triboluminescent Materials into Polymer Matrices
2008
This work describes the synthesis and use of new diblock copolymers to integrate functional inorganic particles into a polymer matrix. These diblock copolymers were synthesized by nitroxide-mediated polymerization (NMP) from styrene and two styrene-like monomers with protected functional groups for the later connection to the functional inorganic material. It was possible to keep the polydispersity of the block copolymers around or below 1.2 and to preset the length of the functional block to about 20 monomers or 10 mol-% of monomers. The groups for the surface functionalization (amino groups or chelating ligands) were obtained in their free form by polymer analogous reactions. As an exampl…
Micelles Formed by Cylindrical Brush-Coil Block Copolymers
2005
Amphiphilic cylindrical brush-coil block copolymers consisting of a polystyrene coil and a cylindrical brush block with poly(acrylic acid) side chains are prepared by ATRP of t-butylacrylate from a block comacroinitiator. Upon acidolysis of the poly(t-butylacrylate), water-soluble polymers were obtained that were observed to form micelles consisting of 4-5 block copolymers on average in aqueous solution. The star-like nature of such micelles was clearly visualized by scanning force microscopy.
Mechanical relaxation in miscible polymer systems: the glass transition regime in poly(vinylmethylether) (PVME)-cross-polystyrene (PS) semi-interpene…
1990
Abstract Miscible semi-interpenetrating polymer networks (semi-IPN) of varying composition are prepared by crosslinking polystyrene containing few maleic anhydride groups with a diamine in the presence of linear poly(vinylmethylether) (PVME). The resulting PVME-c-P(ScoMA) semi-IPNs are characterized by their thermal and thermomechanical behaviour. Comparison with the corresponding uncrosslinked material proves that weak crosslinking has a negligible effect on the location of the glass transition as measured by d.s.c. Both the Tg data and the temperatures of the loss modulus maximum E″ (at 1 rad/s) show the same non-linear curved composition dependence. Contrary to this the tan δ maximum var…