Search results for "Surfaces"
showing 10 items of 2837 documents
Growth of titanium oxynitride layers by short pulsed Nd:YAG laser treatment of Ti plates: Influence of the cumulated laser fluence.
2009
International audience; Titanium oxynitride layerswere formed by surface laser treatment of Ti plates in air using a Nd:YAG laser source of short pulse duration about 5 ns. The cumulated laser fluence was varied in the 100–1200 J cm2 range and its influence on the composition and the structure of the formed layers was studied by different characterization techniques providing physico-chemical and structural information. It was shown that the laser treatment induces the insertion of light elements as O, N and C in the formed layer with the amount increasing with the laser fluence. The in-depth composition of the layers and the co-existence of different phases were also studied. The way in wh…
Conductimetry and impedance spectroscopy study of low pressure metal organic chemical vapor deposition TiN O films as a function of the growth temper…
2001
Abstract Titanium oxinitride thin films have been grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) using titanium isopropoxide, Ti(OCH(CH 3 ) 2 ) 4 (TIP) and NH 3 precursors in a growth temperature range from 450 to 750°C on sapphire substrates. The electrical behaviour of these films was studied between 400 and 173 K, revealing three different behaviours, ranking from a hopping conductivity (450–500°C) to a conducting one (700–750°C), with a dual behaviour for the intermediate growth temperatures. Moreover, at room temperature, both conductimetry and impedance spectroscopy highlighted a percolation behaviour, interpreted in terms of continuum percolation. The effect…
Wavelength influence on nitrogen insertion into titanium by nanosecond pulsed laser irradiation in air
2013
Abstract We studied in this work the influence of the wavelength (532 vs. 1064 nm) on the insertion of nitrogen in titanium targets by surface laser treatments in air. The laser pulses were of 5 ns and the irradiance was lower than 25 × 10 12 W/m 2 . Results obtained using a frequency-doubled Nd:YAG laser at 532 nm were compared with those previously reported for laser treatments at 1064 nm. Nuclear reaction analysis and micro-Raman spectroscopy were used for determining the composition and the structure of the surface layers, respectively. Results showed the lower efficiency of irradiation at 532 nm for nitrogen insertion, which is possible only above threshold conditions depending on bot…
Humidity-Induced Grain Boundaries in MAPbI3 Perovskite Films
2016
Methylammonium lead halide perovskites (MAPbI3) are very sensitive to humid environments. We performed in situ scanning force microscopy and in situ X-ray diffraction measurements on MAPbI3 films to track changes in the film morphology and crystal structure upon repeated exposure to a high relative humidity environment (80%). We found that the appearance of monohydrate (MAPbI3·H2O) Bragg reflections coincided with the appearance of additional grain boundaries. Prolonging the exposure time to humidity induced more grain boundaries and steps in the MAPbI3 films, and the peak intensities of the monohydrate MAPbI3·H2O increased. The monohydrate was not stable under dry atmosphere and could be r…
Resonant Raman characterisation of ultra-thin nano-protective carbon layers for magnetic storage devices
2003
Abstract Carbon thin films are very important as protective coatings for a wide range of applications such as magnetic storage devices. The key parameter of interest is the sp3 fraction, since it controls the mechanical properties of the film. Visible Raman spectroscopy is a very popular technique to determine the carbon bonding. However, the visible Raman spectra mainly depend on the configuration and clustering of the sp2 sites. This can result in the Raman spectra of different samples looking similar albeit having a different structure. Thus, visible Raman alone cannot be used to derive the sp3 content. Here we monitor the carbon bonding by using a combined study of Raman spectra taken a…
A nanostructured sensor of hydrogen peroxide
2017
Abstract A nanostructured electrochemical sensor of hydrogen peroxide was fabricated growing self-standing Pd nanowires (Pd NWs) into polycarbonate (PC) membranes through a simple metal galvanic deposition. Conditions of deposition were adjusted in order to attain 2–5 μm long Pd wires. Characterization of Pd-NWs was performed by scanning electrode microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction. Properties of the nanostructured sensor were studied by cyclic voltammetry and chronoamperometry in phosphate buffer—ethanol solution. Addition of pure ethanol to the test solution was essential in order to increase wettability of the nanostructures. Sensing features were comp…
Au Adsorption on Regular and Defected Thin MgO(100) Films Supported by Mo
2007
Using density functional theory we studied systematically a Au atom adsorption on a Mo-supported regular and defected ultrathin MgO film with 1 to 5 ML thickness. On Mo(100) grown regular MgO Au prefers to adsorb at a hollow site instead of an O site found for single-crystal MgO. The metal support also enhances Au adsorption energy in agreement with the earlier theoretical results. Adsorption energy decreases with increasing film thickness being, however, even in the case of 5 ML thick MgO much higher than that on single-crystal MgO. The Bader analysis was performed to estimate the spatial distribution of charge in different cases. The results show charge transfer (0.7−0.8 e) to the Au atom…
XPS analysis of sol-gel-generated mixed-oxide layers for biomedical application
2002
The excellent biocompatibility of titanium and its alloys is associated with the properties of their dense TiO2 layer on the surface. The adsorption of proteins of the body fluid to implant surfaces depends on the properties of the surface oxide layer, especially the electronic structure. Therefore, tailoring of the oxide layer is a method for influencing protein adsorption. In this study, titanium platelets are coated by the sol–gel process with mixed oxides containing the biocompatible elements Ti, Nb, Zr and Ta. In order to verify the composition of the produced oxide layer, which can differ from the adjusted precursor composition in the sol because of different reactivities of the precu…
Investigations of the corrosion protection of ultrathin a-C and a-C:N overcoats for magnetic storage devices
2004
Abstract The thickness-dependent corrosion protection of carbon overcoats for magnetic hard disks can be analyzed by collecting X-ray absorption near edge structure (XANES) spectra at the Co L3-edge. Co is the main constituent of the protected magnetic media underneath. The spectra of the Co absorption edge display a strong peak for pure metallic, non-oxidized Co. This peak splits up into several sub-structures for oxidized Co. Therefore, XANES spectra provide a straightforward method to determine the overcoat thickness, leading to closed coverage and corrosion protection of the underlying material. A similar approach was carried out by X-ray photoelectron spectroscopy (XPS). Standard a-C:N…
Structural and electrical properties of cerium tungstate: Application to methane conversion
2020
International audience; The catalytic efficiency as well as the electrical conduction mechanism of Ce2(WO4)3 powders synthetized for the oxidation of methane were investigated. Total and partial oxidation reactions were observed in the temperature range between 600 and 750 °C under CH4/dry air flux, for low CH4 concentrations. The electrical conduction mechanism is based on electron tunneling at low temperature (< 650 °C) and hopping over an ion barrier at high temperature, which favors the catalytic oxidation of CH4 in air; these mechanisms occur during the partial and total oxidation under weak gas flow. The occurrence of these types of conduction mechanism was related both to the distort…