Search results for "Surfaces"
showing 10 items of 2837 documents
Structure of the FeBTC Metal–Organic Framework: A Model Based on the Local Environment Study
2015
The local environment of iron in FeBTC, a metal organic framework commercially known as Basolite F300, is investigated combining XANES and EXAFS studies of the iron K-edge. The building block of the FeBTC can be described as an iron acetate moiety. Dehydration induces a change in the coordination of the first shell while preserving the network. We propose that the local structure around Fe atoms does not undergo a rearrangement, thus, leading to the formation of an open site. The analysis conveys that the FeBTC is a disordered network of locally ordered blocks.
SnO2 : Sb - A new material for high-temperature MEMS heater applications: Performance and limitations
2007
MEMS micro heater devices capable of long-term operation at temperatures up to 1000 degrees C are presented. The enhanced long-term stability has been achieved by employing antimony-doped tin oxide (SnO2:Sb) as a substitute for the conventionally used noble metal heater resistors. A detailed investigation of its high-temperature stability reveals that degradation is caused by out-diffusion of Sb impurities from the SnO2 film. (c) 2007 Elsevier B.V. All rights reserved.
Gas sensing properties of multiwall carbon nanotubes decorated with rhodium nanoparticles
2011
International audience; In the present work, multiwalled carbon nanotubes were decorated with rhodium nanoparticles using a colloidal solution in the post-discharge of an RF atmospheric plasma of argon (Ar) or argon/oxygen (Ar:O 2). The properties of these hybrid materials towards the room temperature detection of NO 2 , C 2 H 4 , CO, C 6 H 6 and moisture were investigated and discussed in view of compositional and morphological studies. It was found that the presence of oxygen in the plasma treatment is essential to significantly enhance the gas response of Rh-decorated multiwalled carbon nanotubes and to avoid response saturation even at low gas/vapor concentrations. These desirable effec…
Making Graphene Luminescent by Direct Laser Writing
2020
Graphene is not intrinsically luminescent, due to a lack of bandgap, and methods for its creation are tricky for device fabrication. In this study, we create luminescent graphene patterns by a simple direct laser writing method. We analyze the graphene using Raman spectroscopy and find that the laser writing leads to generation of line defects after initial formation of point defects. This Raman data enables us to create a model that explains the luminescence by a formation of small domains due to confinement of graphene by line defects, which is conceptually similar to the mechanism of luminescence in graphene quantum dots. peerReviewed
Vacuum deposited perovskite solar cells employing dopant-free triazatruxene as the hole transport material
2017
Abstract Planar perovskite solar cells using organic charge selective contacts were fabricated. In a vacuum deposited perovskite-based solar cell, dopant and additive free triazatruxene as the hole transport layer was introduced for device fabrication. High open-circuit voltage of 1090 mV was obtained using methylammonium lead iodide (Eg=1.55 eV) as light harvesting material, thus representing a loss of only 460 mV which is in close vicinity of mature silicon technology (400 mV). The devices showed a very competitive photovoltaic performance, monochromatic incident photon-to-electron conversion efficiency of 80% and the power conversion efficiencies in excess of 15% were measured with a neg…
Electrochemical Fabrication and Physicochemical Characterization of Metal/High-k Insulating Oxide/Polymer/Electrolyte Junctions
2014
Photoelectrochemical polymerization of poly(3,4-ethylenedioxythiophene), PEDOT, was successfully realized on anodic film grown to 50 V on magnetron sputtered Ti-6 atom % Si alloys. Scanning electron microscopy allowed us to evidence formation of compact and uniform polymer layers on the oxide surface. Photoelectrochemical and impedance measurements showed that photopolymerization allows one to grow PEDOT in its conducting state, while a strong cathodic polarization is necessary to bring the polymer in its p-type semiconducting state. Information on the optical and electrical properties of metal/oxide/polymer/electrolyte junctions proves that PEDOT has promising performance as an electrolyte…
Self-Assembly of Polymer Blends and Nanoparticles through Rapid Solvent Exchange.
2019
Molecular dynamics simulations were performed to study the fabrication of polymeric colloids containing inorganic nanoparticles (NPs) via the flash nanoprecipitation (FNP) technique. During this process, a binary polymer blend, initially in a good solvent for the polymers, is rapidly mixed with NPs and a poor solvent for the polymers that is miscible with the good solvent. The simulations reveal that the polymers formed Janus particles with NPs distributed either on the surface of the aggregates, throughout their interior, or aligned at the interface between the two polymer domains, depending on the NP-polymer and NP-solvent interactions. The loading and surface density of NPs can be contro…
Optical Spectra and Direct Optical Transitions in Amorphous and Crystalline ZnO Thin Films and Powders
2010
Comparative studies of ZnO crystalline and amorphous thin films and nanocrystalline powders are reported. The UV-visible optical spectra were analyzed with special attention paid to the direct optical bandgap. Atmospheric radio-frequency barrier torch discharge and pulsed hollow cathode sputtering techniques for the film fabrication were used. For the crystalline films, similar values of the direct optical bandgap were found independent of the growth method used. The analysis of the amorphous films and powders revealed a pronounced Urbach-like exponential absorption tail approaching the bandedge. For the powders, the bandgap energies were larger than those for the crystalline and amorphous …
Oil-in-Water fL Droplets by Interfacial Spontaneous Fragmentation and Their Electrical Characterization
2019
Inkjet printing is here employed for the first time as a method to produce femtoliter-scale oil droplets dispersed in water. In particular, picoliter-scale fluorinated oil (FC40) droplets are printed in the presence of perfluoro-1-octanol surfactant at a velocity higher than 5 m/s. Femtoliter-scale oil droplets in water are spontaneously formed through a fragmentation process at the water/air interface using minute amounts of nonionic surfactant (down to 0.003% v/v of Tween 80). This fragmentation occurs by a Plateau-Rayleigh mechanism at a moderately high Weber number (10(1)). A microfluidic chip with integrated microelectrodes allows droplets characterization in terms of number and diamet…
Self-assembled three-dimensional inverted photonic crystals on a photonic chip
2017
Three dimensional photonic crystals (PhCs) exhibiting a full photonic band gap have high potential in optical signal processing and detector applications. However, the challenges in the integration of the 3D PhCs into photonic circuits have so far hindered their exploitation in real devices. This article demonstrates the fabrication of 3D PhCs exploiting the capillary directed self-assembly (CDSA) of monodisperse colloidal silica spheres, their inversion to silicon shells, and integration with silicon waveguides. The measured transmission characteristics agree with numerical predictions and provide strong indication of a full photonic band gap in the inverted 3D photonic crystals at wavelen…