Search results for "T method"
showing 10 items of 1254 documents
Numerical study for a new methodology of flaws detection in train axles
2013
Train loads and travel speeds have increased over time, requiring more efficient non-destructive inspection methods. Railway axles are critical elements; despite being designed to last more than 20 years several cases of premature failure have been recorded. Train axles are inspected regularly, but the limits associated to the traditional inspection technologies create a growing interest towards new solutions. Here a novel non-destructive inspection method of in-service axles based on non-contact data collection is presented. The propagation of surface waves, generated by a thermo-elastic laser source, is investigated using a finite element method based on dynamic explicit integration. Coup…
A lap joint simulant laboratory test method of aluminium alloys
2015
A lap joint simulant cavity (LJSC) with a gap thickness of 200 μm has been developed to test corrosion of assembled coated aluminium alloys. The LJSC was instrumented with electrodes allowing simultaneous pH and potential measurements in 0.5 M NaCl solution. Assuming the outer part of the LJSC is electrochemically inactive (painted sheet) it was confirmed that in free corroding conditions the pH inside the LJSC tends more towards alkalinisation. On the opposite, if the outer part of the LJSC is electrochemically active (unpainted sheet) the pH inside the LJSC tends towards an acidic value.
Deformation and failure of MXene nanosheets
2020
This work is aimed at the development of finite element models and prediction of the mechanical behavior of MXene nanosheets. Using LS-Dyna Explicit software, a finite element model was designed to simulate the nanoindentation process of a two-dimensional MXene Ti3C2Tz monolayer flake and to validate the material model. For the evaluation of the adhesive strength of the free-standing Ti3C2Tz-based film, the model comprised single-layered MXene nanosheets with a specific number of individual flakes, and the reverse engineering method with a curve fitting approach was used. The interlaminar shear strength, in-plane stiffness, and shear energy release rate of MXene film were predicted using th…
Micromechanisms of load transfer in a unidirectional carbon fibre–reinforced epoxy composite due to fibre failures. Part 1: Micromechanisms and 3D an…
2006
This study gives a detailed analysis of load distributions around fibre breaks in a composite and the mechanisms involved in load transfer. In contrast to other studies reported in the literature the analysis considers different configurations of composite damage from the failure of a few fibres to the failure of many. The model considers the elastic case with and without debonding at the broken fibre/matrix interface. In this way, the usual limitations of the finite element approach are overcome so as to take into account the numbers and interactions of broken fibres whilst maintaining an evaluation of the various fields involved, in particular the stress fields associated with fibre failu…
Improving the Efficiency of NFC Systems Through Optimizing the Sintered Ferrite Sheet Thickness Selection
2020
The reduction of embedded portable devices involves a magnetic field interference problem when it integrates near field communication (NFC) due to the presence of conductive surfaces, such as ground planes, batteries, or metallic enclosures. Flexible sintered ferrite sheets (FSFS) represent an interesting shielding solution to prevent electromagnetic interferences problems related to NFC, thanks to their ability to control the magnetic flux. The characterization of FSFS effectiveness is analyzed as a function of the sheet thickness in this contribution. This is performed with the aim of determining which is the optimum thickness value to retune an NFC antenna to its original operation frequ…
A shear test for structural adhesives used in the consolidation of old timber
2001
A test method was developed specifically for structural adhesives used in thick joints. It is based on compressive shear loading of glued joints (GJ) and solid wood (SW) specimens, before and after a suitable accelerated ageing cycle. The evaluation of results is based on the ratios of wet strength to dry strength and on the comparison of GJ specimens to SW specimens which are prepared from the same batch of wood, in order to minimise the influence of the variability in wood characteristics. On a group of 10 epoxy-based adhesives, specifically marketed for the consolidation of old timber structures, the method has proved to be effective to differentiate the performances of each product. Amo…
Electromechanical Impedance Method to Assess the Stability of Dental Implants
2017
In this paper we illustrate the application of the electromechanical impedance (EMI) technique, popular in structural health monitoring, to assess the stability of dental implants. The technique consists of bonding a piezoelectric transducer to the element to be monitored. When subjected to an electric field, the transducer induces low to high frequency structural excitations which, in turn, affect the transducer's electrical admittance. As the structural vibrations depend on the mechanical impedance of the host structure (in this case the implant secured to the jaw), the measurement of the PZT's admittance can infer the progress of the osseointegration process. In the study presented in th…
The modeling of dissimilar welding of immiscible materials by using a phase field method
2013
A multiphysical model of high power beam welding of immiscible materials is developed to explain the influence of operational parameters and materials properties on resulting morphology by simultaneous solving of heat transfer, fluid flow and mass transfer problems. The introduction of phase field description of the interface motion between two immiscible liquids allows obtaining the cartography of melted zone in function of two key-parameters: the position of heat source relatively to joint line and the welding speed. Due to the short thermal cycle limiting mass transfer, high power beam welding techniques may result in very inhomogeneous melted zones. In this study, the interest is paid t…
Using a neural network for predicting the average grain size in friction stir welding processes
2009
In the paper the microstructural phenomena in terms of average grain size occurring in friction stir welding (FSW) processes are focused. A neural network was linked to a finite element model (FEM) of the process to predict the average grain size values. The utilized net was trained starting from experimental data and numerical results of butt joints and then tested on further butt, lap and T-joints. The obtained results show the capability of the AI technique in conjunction with the FE tool to predict the final microstructure in the FSW joints.
Continuous dynamic recrystallization phenomena modelling in friction stir welding of aluminium alloys: A neural-network-based approach
2007
The current paper focuses on the continuous dynamic recrystallization phenomena (CDRX) occurring in friction stir welding processes of AA6082 T6 aluminium alloys. In particular, in order to predict the average grain size, a properly trained neural network is linked to the finite element method (FEM) model of the process. The utilized net, which takes as inputs the local values of strain, strain rate, and temperature, was trained starting from experimental data and numerical results. The obtained results show the capability of the artificial intelligence (AI) technique in conjunction with the FE tool to predict the final microstructure in the joint section.