Search results for "Tecnologie"
showing 10 items of 1379 documents
Characterization of kefir-like beverages produced from vegetable juices
2016
The aim of this work was to develop new non-dairy fermented beverages using vegetable juices as fermentable substrates. Carrot, fennel, melon, onion, tomato and strawberry juices underwent back-slopping fermentations, carried out by water kefir microorganisms. Results indicated that lactic acid bacteria and yeasts were capable of growing in the juices tested. Melon juice registered the highest numbers of microorganisms. Almost all juices underwent a lactic fermentation. After fermentation, there was observance of a decrease of the soluble solid content and an increase of the number of volatile organic compounds. In particular, esters were present in high amounts after the fermentation, espe…
Screening of durum wheat landraces (Triticum turgidum subsp. durum) for the malting suitability
2018
Abstract Durum (T. turgidum subsp. durum) wheat production worldwide is substantially less than that of common wheat (Triticum aestivum) mainly due to the relatively limited end-users. In order to evaluate malting and brewing suitability, sixteen old durum wheat landraces were malted at micro scale. Results show malt quality parameters in the range 78.2–85.9% for the extract, 72.9–80.9% for the fermentability, 3–5 EBC units for the colour, 0.49–0.79% dm for water-extractable arabinoxylans and 0.043–0.059% dm for the β-glucans. Regarding wort viscosity (1.53–1.92 mPa s), we found negative correlation with endo-1,4-β-D-xylanase, positive correlation with endo-β-glucanases and soluble proteins…
Selective photocatalytic oxidation of aromatic alcohols in water by using P-doped g-C3N4
2018
A set of bare and P-doped graphitic carbon nitride (g-C3N4) photocatalysts has been prepared by thermal condensation of melamine, urea or thiourea. For the sake of comparison, a g-C3N4 sample obtained in the presence of cyanuric acid and thermally exfoliated C3N4 powders were also studied. The materials were physicochemically characterized and their photocatalytic activity was studied for the selective oxidation of benzyl alcohol (BA), 4-methoxy benzyl alcohol (4-MBA) and piperonyl alcohol (PA) in water suspension both under UV and visible light irradiation. The influence of the type and position of the substituents on conversion and selectivity to aldehyde was remarkable. The presence of P…
Analysis of Electrical Energy Demands in Friction Stir Welding of Aluminum Alloys
2017
Abstract Manufacturing processes, as used for discrete part manufacturing, are responsible for a substantial part of the environmental impact of products. Despite that, most of metalworking processes are still poorly documented in terms of environmental footprint. To be more specific, the scientific research has well covered conventional machining processes, concerning the other processes there is a lack of knowledge in terms of environmental load characterization instead. The present paper aims to contribute to fill this knowledge gap and an energetic analysis of Friction Stir welding (FSW) is presented. Following the CO2PE! methodological approach, power studies and a preliminary time stu…
Advancing manufacturing systems research at NAMRC 46
2018
Research on manufacturing systems is further enriched and becomes stronger at the 46th North American Manufacturing Research Conference (NAMRC 46) at Texas A&M University, College Station, TX, USA. Advancing manufacturing systems is more prevalent than before due to recent industrial revolution (or Industry 4.0), continuous business decentralisation and needs for better overall resource efficiency and effectiveness. Manufacturers are competing in a global, dynamic marketplace that demands excellence in quality and service, throughput, innovativeness, agility in production, short response time to changing markets, and tight profitable margins. In the 21st century, manufacturing will be g…
Energy demand reduction of aluminum alloys recycling through friction stir extrusion processes implementation
2019
Abstract Aluminum alloys are characterized by high-energy demands for primary production. Recycling is a well-documented strategy to lower the environmental impact of light alloys production. Despite that, conventional recycling processes are still energy-intensive with a low energy efficiency. Also, permanent material losses occur during remelting because of oxidation. Recently, several solid-state recycling approaches have been analyzed; in fact, by avoiding the remelting step both energy and material can be saved and, therefore, the embodied energy of secondary production can be substantially reduced. In this paper, the solid-state approach Friction Stir Extrusion (FSE) is analyzed for a…
Towards criteria for sustainable process selection: On the modelling of pure subtractive versus additive/subtractive integrated manufacturing approac…
2017
Additive Manufacturing (AM) processes can be counted among the disruptive technologies that are capable of transforming conventional manufacturing routes. The ability to create complex geometries, the reduction in material scraps during manufacturing, and the light-weighting due to the think-additive redesign of the components represent the main points of strength of AM. However, for some applications (such as the production of metal components for the automotive and aerospace industries), the surface finishing and dimensional/geometrical part tolerancing that can be achieved via AM processes might not be adequate to satisfy the imposed product specifications, and finish machining operation…
Weld quality prediction in linear friction welding of AA6082-T6 through an integrated numerical tool
2016
Abstract A numerical and an experimental campaign were carried out with varying oscillation frequency and interface pressure. The local values of the main field variables at the contact interface between the specimens were predicted by a Lagrangian, implicit, thermo-mechanical FEM model and used as input of a dedicated Neural Network (NN). The NN, integrated in the FEM environment, was designed in order to calculate both a Boolean output, indicating the occurrence of welding, and a continuous output, indicating the quality of the obtained solid state weld. The analysis of the obtained results allowed three different levels of bonding quality, i.e., no weld, sound weld and excess of heat, to…
Effect of the mutual position between weld seam and reinforcement on the residual stress distribution in Friction Stir Welding of AA6082 skin and str…
2016
Abstract In the paper, a numerical and experimental study was carried out to highlight the effect of the distance d between the weld seam and the reinforcement on the residual stress distribution in Friction Stir Welded AA6082-T6 structures. An L-shaped profile was welded to a sheet metal with varying tool rotation and distance d from the weld seam. The Cut Compliance method was used to determine the resulting longitudinal residual stress. A dedicated FE model for FSW was set up, validated and utilized to predict the longitudinal residual stress in the assembled part. The analysis allowed the identification of a few design guidelines in order to reduce the detrimental effects of the residua…
Assessment of material models through simple machining tests
2008
The accuracy of the results obtained from FEM simulation of machining operations depends on the accuracy of input data. Among these, the flow stress data of the workpiece are extremely important together with the friction along the tool-chip interface. In this study, an identification procedure for the determination of material parameters that are used for the FEM simulation of machining processes is proposed. The procedure is based on the coupling of a numerical identification procedure and Arbitrarian Lagrangian Eulerian (ALE) Finite Element simulations of turning operations. An experimental campaign was developed in order to calibrate the model and to validate the procedure. The basic id…