Search results for "Testing"
showing 10 items of 1769 documents
Crack growth models for multiaxial fatigue in a ship’s propeller shaft
2021
Abstract A premature fatigue failure of a large intermediate propeller shaft in a shuttle tanker is discussed and analyzed. The short fatigue life consists mainly of a crack growth phase. Life predictions are carried out by crack growth modelling based on engineering fracture mechanics. The purpose of the present investigation is to identify the most likely loading modes based on the evolution of the crack propagation. A Linear Elastic Fracture Mechanics Model (LEFM) is applied with the stress intensity factor range entering the Paris law as a key parameter. Existing formulas for the geometry functions are supplemented by more detailed stress intensity factor calculations pertaining to smal…
Coded excitation speeds up the detection of the fundamental flexural guided wave in coated tubes
2016
The fundamental flexural guided wave (FFGW) permits ultrasonic assessment of the wall thickness of solid waveguides, such as tubes or, e.g., long cortical bones. Recently, an optical non-contact method was proposed for ultrasound excitation and detection with the aim of facilitating the FFGW reception by suppressing the interfering modes from the soft coating. This technique suffers from low SNR and requires iterative physical scanning across the source-receiver distance for 2D-FFT analysis. This means that SNR improvement achieved by temporal averaging becomes time-consuming (several minutes) which reduces the applicability of the technique, especially in time-critical applications such as…
Discontinuous FRP-Confinement of Masonry Columns
2020
Recent seismic events, all over the world, demonstrated that masonry constructions are prone to brittle collapses when shear or compression capacity is reached. It is clear that, in many real cases, masonry columns need to be strengthened for enhancing their load-carrying capacity and to develop a more ductile response. The Fiber Reinforced Polymers (FRPs) confinement of masonry columns is a well-known technique that may produce these advantages. Unfortunately, full-wrapping insulates the column from the environment; so interstitial humidity can easily occur and cause the acceleration of the masonry's decay. In order to prevent it, partial-confinement is commonly assessed instead of total-j…
Effect of bleaching agents on sealing properties of different intraorifice barriers and root filling materials
2012
Objective: To evaluate the effect of intracoronal bleaching agents on the sealing properties of different intraorifice barriers and root filling materials. Study Design: The root canals of extracted human premolars (n=180) were prepared by using System GT rotary files and filled with either gutta-percha+AH Plus or Resilon+Epiphany sealer. In both groups, the coronal 3mm of root filling was removed and replaced with one of the following materials applied as intraorifice barriers (n=30/group): 1. ProProot-MTA; 2. Conventional Glass ionomer cement; and 3. Hybrid resin composite. In each subgroup, intracoronal bleaching was performed using either sodium perborate with distilled water or 35% hyd…
Energy leaks through the optical barrier created by H+ implantation in BaTiO3 and LiNbO3 planar waveguides
1998
Abstract The energy leaks through the index barrier created by the proton implantation process are put in evidence in planar optical waveguides made in BaTiO 3 and LiNbO 3 substrates. The selective detection of the light emerging from the guiding region permits to measure the optical attenuation of the guided wave. The results obtained on mono or twice implanted LiNbO 3 and BaTiO 3 waveguides are presented and discussed. It is shown that the light confinement is better in BaTiO 3 than in LiNbO 3 .
A numerical and experimental study through laser thermography for defect detection on metal additive manufactured parts
2017
Additive manufacturing has been recently employed in industrial sectors with the fundamental requirement for zero defect parts. Technological developments in additive manufacturing notwithstanding, there continues to be a scarcity of non-destructive inspection techniques to be exploited during the manufacturing process itself, thus limiting industrial advancements and extensive applications. Therefore, being able to integrate the defect inspection phase within the additive manufacturing process would open the way to enabling corrective actions on the component in itinere, that is, before reaching the final product. For this reason, new methods of in-process monitoring are gaining more and m…
Use of micro-tomography for validation of method to identify interfacial shear strength from tensile tests of short regenerated cellulose fibre compo…
2016
The interfacial shear strength of short regenerated cellulose fibre/polylactide composites was characterized by means of an industry-friendly adhesion test method. The interfacial shear strength was back-calculated from the experimental tensile stress-strain curves of composites by using a micro-mechanical model. The parameters characterizing the microstructure of the composites, e.g. fibre length and orientation distributions, used as input in the model were obtained by micro-tomography. The investigation was carried out on composites with untreated and surface treated fibres with various fibre weight contents (5wt%, 10wt%, and 15wt% for untreated fibres, and 15wt% for treated fibres). The…
Influence of the Number of Nanoparticles on the Enhancement Properties of Surface-Enhanced Raman Scattering Active Area: Sensitivity versus Repeatabi…
2011
In the present work, the combination of chemical immobilization with electron beam lithography enables the production of sensitive and reproducible SERS-active areas composed of stochastic arrangements of gold nanoparticles. The number of nanoparticles was varied from 2 to 500. Thereby a systematic analysis of these SERS-active areas allows us to study SERS efficiency as a function of the number of nanoparticles. We found that the experimental parameters are critical, in particular the size of the SERS-active area must be comparable to the effective area of excitation to obtained reproducible SERS measurements. The sensitivity has also been studied by deducing the number of NPs that generat…
Elastic Superhydrophobic and Photocatalytic Active Films Used as Blood Repellent Dressing.
2020
Durable and biocompatible superhydrophobic surfaces are of significant potential use in biomedical applications. Here, a nonfluorinated, elastic, superhydrophobic film that can be used for medical wound dressings to enhance their hemostasis function is introduced. The film is formed by titanium dioxide nanoparticles, which are chemically crosslinked in a poly(dimethylsiloxane) (PDMS) matrix. The PDMS crosslinks result in large strain elasticity of the film, so that it conforms to deformations of the substrate. The photocatalytic activity of the titanium dioxide provides surfaces with both self-cleaning and antibacterial properties. Facile coating of conventional wound dressings is demonstra…
Photoalignment and Surface-Relief-Grating Formation are Efficiently Combined in Low-Molecular-Weight Halogen-Bonded Complexes
2012
It is demonstrated that halogen bonding can be used to construct low-molecular-weight supramolecular complexes with unique light-responsive properties. In particular, halogen bonding drives the formation of a photoresponsive liquid-crystalline complex between a non-mesogenic halogen bond-donor molecule incorporating an azo group, and a non-mesogenic alkoxystilbazole moiety, acting as a halogen bond-acceptor. Upon irradiation with polarized light, the complex exhibits a high degree of photoinduced anisotropy (order parameter of molecular alignment > 0.5). Moreover, efficient photoinduced surface-relief-grating (SRG) formation occurs upon irradiation with a light interference pattern, with…