Search results for "Thermography"
showing 10 items of 146 documents
Influence of mode stirrer and air renewal on controlled microwave drying of sliced zucchini
2017
An on-line temperature-controlled microwave (MW) system, based on infrared thermography, was developed for drying zucchini slices. Moreover, the effects of different configurations, including turntable rotation, mode stirrer and air renewal, alone or in combination, on drying kinetics and quality of dried product were evaluated. The combination of stirrer and air renewal reduced the drying time of zucchini slices by about 48% with respect to the basic configuration and by 22% with respect to air renewal only. The lowest oscillation of temperatures about the fixed level (65 °C) was found when operating with the stirrer mode, because of the improved uniformity of the MW distribution. The sa…
Moisture ingress in photovoltaic modules: A review
2021
Abstract Moisture ingress in photovoltaic (PV) modules is the core of most degradation mechanisms that lead to PV module power degradation. Moisture in EVA encapsulant can lead to metal grids corrosion, delamination and discolouration of encapsulants, potential induced degradation, optical and adhesion losses. The present work is a review of literature on the causes, effects, detection, and mitigation techniques of moisture ingress in PV modules. Literature highlights on determining the diffusivity, solubility, and permeability of polymeric components of PV modules via water vapour transmission rate tests, gravimetric, and immersion methods, have been presented. Electroluminescence, photolu…
Novel non-destructive evaluation technique for the detection of poor dispersion of carbon nanotubes in nanocomposites
2019
Abstract A wide use of advanced carbon nanotube polymer composites can be boosted by new non-destructive evaluation (NDE) techniques that can test the quality of the products to ensure that their specifications are met. It is well known in literature that the parameter that far more than others can affect the enhancing capabilities of the carbon nanotubes is their dispersion. Here we have presented a novel NDE technique based on infrared thermography able to evaluate the dispersion of the added nanoparticles in polymer nanocomposites. The NDE technique was used to compare pairs of samples whose difference is represented only by the level of dispersion. It was found a significant difference …
Detection and characterisation of disbonds on Fibre Metal Laminate hybrid composites by flying laser spot thermography
2017
Abstract In this work a novel data collection and processing is proposed for the Infrared Non-Destructive Testing (IR-NDT) of interlaminar disbonds on Fibre Metal Laminate (FML) hybrid composites. The adopted active IR-NDT scheme uses a pointwise laser heat source that is moved along a raster scanning trajectory over the object surface. A Focal Plane Array IR camera is employed to acquire the thermal field generated by the moving heat source. Disbonds defect signatures are then searched by analysing the perturbations of the temperature distribution over a reference area following the heat source. The proposed methodology has been implemented on a GLARE sample, since this class of FMLs has g…
A Numerical Study on Interlaminar Defects Characterization in Fibre Metal Laminates with Flying Laser Spot Thermography
2018
This work describes a numerical study on non-destructive evaluation of interlayer disbond defects in aerospace grade Fibre Metal Laminate sheets (FMLs). A recently proposed infrared non-destructive testing setup is considered, where a continuous laser is moved over the material surface, while the thermal footprint of the moving heat source is acquired, e.g. by an infrared thermal camera. Interlayer disbonds are then detected by analysing the features of the acquired thermograms. The experimental feasibility of this approach has been recently proved. The present work proposes a numerical simulation of the NDT approach, where the material thermal response is analysed and correlated to defects…
Fiber-pigtailed temperature sensors based on dielectric-loaded plasmonic waveguide-ring resonators.
2012
We demonstrate optical fiber-pigtailed temperature sensors based on dielectric-loaded surface plasmon-polariton waveguide-ring resonators (DLSPP-WRRs), whose transmission depends on the ambient temperature. The DLSPP-WRR-based temperature sensors represent polymer ridge waveguides (~1×1 µm(2) in cross section) forming 5-µm-radius rings coupled to straight waveguides fabricated by UV-lithography on a 50-nm-thick gold layer atop a 2.3-µm-thick CYTOP layer covering a Si wafer. A broadband light source is used to characterize the DLSPP-WRR wavelength-dependent transmission in the range of 1480-1600 nm and to select the DLSPP-WRR component for temperature sensing. In- and out-coupling single-mod…
A procedure to achieve fine control in MW processing of foods
2007
Abstract A two-dimensional analytical model for predicting the unsteady temperature field in a cylindrical shaped body affected by spatially varying heat generation is presented. The dimensionless problem is solved analytically by using both partial solutions and the variation of parameters techniques. Having in mind industrial microwave heating for food pasteurization, the easy-to-handle solution is used to confirm the intrinsic lack of spatial uniformity of such a treatment in comparison to the traditional one. From an experimental point of view, a batch pasteurization treatment was realized to compare the effect of two different control techniques both based on IR thermography readout: t…
A simple technique for estimating surface temperature by means of a thermal infrared radiometer
1992
Abstract In this Letter we present a simple technique for estimating surface temperatures from data obtained by means of a thermal infrared radiometer. The technique is based simply on the use of a table and a graph, from which cmissivity and atmospheric effects are easily evaluated. The accuracy is better than a tenth of a degree when emissivity and atmospheric radiance arc known.
Application of silicon-based camera for measurement of non-homogeneous thermal field on realistic specimen surface
2019
Abstract The high-cost low-resolution infrared cameras operating in middle infrared spectral ranges are widely used to detect the thermal fields. In this study, a low-cost high-resolution silicon-based sensor camera operating in near infrared spectral ranges is used to perform the observation of the thermal fields on the realistic steel specimen surface. In near-infrared spectral ranges, a small temperature variation led to a large modification in the sensor illumination, inducing acquired images with over saturation or poor dynamic range of gray levels. To address this problem, an algorithm was used to precisely adjust the exposure time to acquire images with constant gray level whatever t…
Drying rate control in microwave assisted processing of sliced apples
2018
The most enhanced microwave systems for the preparation of quality-dehydrated fruits continuously adjust the power level in order to maintain the product temperature above a target value. As a result, typical drying curves that exhibit high drying rates in the middle stage are obtained. This can often lead to quality damage or undesirable changes on food colour and texture. In response to these issues, a microwave system is proposed that can realise drying processes keeping drying rates constant. This approach required a continuous temperature adjustment of the apple slices under test, whose temperature was detected by a computer-aided infrared thermography system. Since temperature correct…