Search results for "Titanium oxide"
showing 10 items of 58 documents
Self-assembled titania-silica-sepiolite based nanocomposites for water decontamination
2009
WOS: 000264524200020
The defined adsorption site of sodium on the TiO2(110)–(1×1) surface
2004
The adsorption site of sodium on the TiO2(1 1 0)–(1 × 1) surface was studied by extended X-ray absorption fine structure. For coverage ranging between 0.25 and 0.5 ML, we find that sodium is on an ‘in-between' site where it is bound to two bridging oxygen atoms at 2.25 Å and one in-plane oxygen atom at 2.40 Å, in full agreement with DFT calculations. At higher coverage the site becomes an hollow site where the sodium atom is equidistant to the three oxygen atoms at 2.30 Å, while metallic sodium clusters are also formed at the surface.
NiO diluted in high surface area TiO2 as efficient catalysts for the oxidative dehydrogenation of ethane
2017
[EN] Catalysts consisting of NiO diluted in high surface area TiO2 can be as efficient in the oxidative dehydrogenation of ethane as the most selective NiO-promoted catalysts reported previously in the literature. By selecting the titania matrix and the NiO loading, yields to ethylene over 40% have been obtained. In the present article, three different titanium oxides (TiO2) have been employed as supports or diluters of nickel oxide and have been tested in the oxidative dehydrogenation of ethane to ethylene. All TiO2 used present anatase as the main crystalline phase and different surface areas of 11,55 and 85 m(2) g(-1). It has been observed that by selecting an appropriate nickel loading …
Study of surface layers and ejected powder formed by oxidation of titanium substrates with a pulsed Nd:YAG laser beam.
2009
Laser treatment of a titanium surface at certain conditions initiates the formation of titanium oxide layers as well as micro (nano) scale powder ejected from the surface of the substrate. The resultant morphology of the surface as well as the size and the structure of the particles are all strongly dependent on the treatment parameters (laser fluence, pulse frequency, overlap parameter, etc.). In this study, titanium substrates were treated with an industrial pulsed Nd:YAG laser in air, with varying parameters. Surface layers and ejected materials were compared using scanning and transmission electron microscopy, X-ray diffraction and Raman spectroscopy. The rutile phase of TiO(2) dominate…
A comparative study of the photocatalytic activities of iron-titanium (IV) oxide photocatalysts prepared by various methods; spray pyrolysis, impregn…
1995
Abstract A series of iron/titanium oxide photocatalysts of varying Fe 3+ content have beenprepared by a number of different methods and subjected to controlled thermal treatment. Specimens have been characterised in terms of their crystalline structure and morphology, and indicate solid solutions containing both the anatase and rutile phases of TiO 2 , together with the formation of pseudo-brookite in some specimens. Intrinsic photo-activity measurements have been performed using a standard liquid-phase photocatalytic reaction. Results indicate that the photocatalytic activity of the specimens differs according to the method of preparation, and that all solids containing iron (III) species …
TiO2 anatase films obtained by direct liquid injection atomic layer deposition at low temperature
2014
International audience; TiO2 thin films were grown by direct liquid injection atomic layer deposition (DLI-ALD) with infrared rapid thermal heating using titanium tetraisopropoxide and water as precursors. This titanium tetraisopropoxide/water process exhibited a growth rate of 0.018 nm/cycle in a self-limited ALD growth mode at 280 degrees C. Scanning electron microscopy and atomic force microscopy analyses have shown a smooth surface with a low roughness. XPS results demonstrated that the films were pure and close to the TiO2 stoichiometric composition in depth. Raman spectroscopy revealed that the films were crystallized to the anatase structure in the as-deposited state at low temperatu…
Structural Studies of Titanium Oxide Multilayers
2005
Multilayers of titanium oxide on conductive glasses (silica, covered with indium/tin and tin oxides) were obtained by different methods (from suspension, by sol–gel, by vacuum sputtering). X-ray diffraction and positron annihilation depth-resolved characterization of these samples are presented. The data allow us to determine optimal deposition parameters, in order to obtain the anatase phase, important in practical applications in photoelectrochemical cells.
Photocatalytic thin films of TiO2 formed by a sol-gel process using titanium tetraisopropoxide as the precursor
2008
Abstract Thin TiO 2 films were prepared with the dip-coating technique by using sols deriving from titanium tetraisopropoxide. TiO 2 films were formed on glass substrates previously covered by a SiO 2 layer obtained from a tetraethylortosilicate sol. The films, after a thermal treatment at 673 K, mainly consisted of TiO 2 anatase. The samples were characterised by X-ray diffraction, UV–Vis spectroscopy, scanning electron microscopy and atomic force microscopy. The photoactivity of the various films was tested by using as probe reaction the photo-oxidation of 2-propanol in gas-solid regime. The photoreactivity results indicated that the TiO 2 films were efficient for degrading 2-propanol und…
The effect of silver nanoparticles, zinc oxide nanoparticles, and titanium dioxide nanoparticles on the push-out bond strength of fiber posts
2019
Background This study was undertaken to investigate the effect of intraradicular dentin pretreatment with silver nanoparticles (SNPs), zinc oxide nanoparticles (ZNPs), and titanium oxide nanoparticles (TNPs) on the push-out bond strength (PBS) of fiber posts to root dentin using two types of resin cements. Material and methods Eighty single-rooted human premolar roots were randomly divided into eight groups after endodontic treatment and post space preparation, according to the type of intraradicular dentin pretreatment with different nanoparticle solutions (n=20). The groups included no pretreatment (control) and pretreatments with SNPs, ZNPs, and TNPs. Each group was divided into 2 subgro…
Mechanical performance of experimental acrylic resins modified by nanoparticles after chemical and mechanical degradation.
2020
Background Different materials have been incorporated into the polymethylmethacrylate matrix to improve its performance. The aim of this study was to evaluate the degree of conversion (DC), the flexural strength (FS), the elasticity modulus (EM), and the effect of exposure to food-simulating liquids prior to brushing simulation on the gloss loss (GL) of experimental acrylic resins modified by nanoparticles. Material and methods Three different types of nanoparticles; silicon oxide (SiO2), cerium oxide (CeO2) and titanium oxide (TiO2) were added to a poly (methylmethacrylate) matrix, in proportions of 0.5wt%, 1wt% and 3wt% each, forming nine experimental groups. The acrylic resin was also te…