Search results for "Turing"

Mechanical behaviour of compacted scaly clay during cyclic controlled-suction testing

2007

Scaly clays are stiff and highly fissured soils due to their complex geological history. Owing to these characteristics, they may be placed and compacted as excavated, to obtain a material with adequate engineering properties, suitable as core material in earth dams and in waste isolation fills. With reference to these engineering applications, an exhaustive experimental programme is developed to characterise the hydro-mechanical behaviour of this compacted material under a variety of controlled-suction paths. This paper presents selected test results, focusing on the interpretation of specific behavioural features of the volume change of this complex material; namely, the strain accumulati…

Incorporation of ATP synthetase into long-term stable liposomes of a polymerizable synthetic sulfolipid

1981

Recovery of bioactive compounds from walnut (Juglans regiaL.) green husk by supercritical carbon dioxide extraction

2021

In this work, the use of supercritical carbon dioxide, a nontoxic solvent, was proposed to extract bioactive compounds from Juglans regia L. green husk and was compared to other traditional techniques based on solvents such as ethanol, methanol and water. Supercritical CO2 was combined with ethanol as an organic modifier at a rate of 20% of the total flow to achieve greater extraction of polar compounds. The extracts were characterised in terms of extraction yields, antioxidant activity, total polyphenol content, phenolic acids, juglone, volatile organic compounds and antifungal activity. The results showed that the extracts obtained with supercritical CO2 were rich in polyphenols (10750 mg…

Dispersion Copolymerization of Vinyl Monomers in Supercritical Carbon Dioxide.

2003

The thermally initiated free-radical dispersion copolymerization of methyl methacrylate (MMA) and N,N-dimethylacrylamide (DMA) in supercritical carbon dioxide has been studied in the presence of polysiloxane surfactants. The formation of a stable latex seems to be related to the presence of at least one reactive end group in the surfactant macromolecule, thus suggesting that anchoring of the stabilizer to the surface of the growing polymer particles occurs through chemical grafting. In the case of a molar ratio of DMA to MMA lower than 0.40, microspherical copolymer particles with yields ranging from 81 to 97% were collected from batch polymerizations carried out at 65 °C and 23-28 MPa usin…

Closed-loop supply chains: What reverse logistics factors influence performance?

2016

This paper analyses the inventory and order flow dynamics in closed-loop supply chains (CLSCs). In this kind of supply chains the reverse flow of materials entering the system for recycling purposes complicates the way in which inventories should be managed and replenishment policies should be designed. Specifically, we analyse the relationships between some reverse logistics’ factors (remanufacturing lead-time, return rate of recycled products, reverse order policy, and number of supply chain tiers) on the order and inventory variance amplification. We firstly perform a systematic literature review of the related studies. Secondly, by adopting a difference equation math approach and design…

Do horizontal relationships matter to production and operations managers?

2014

This paper shifts the focus of production, operations and supply chain management business relationships from the vertical to the horizontal side and calls for more research on this issue. The main intent is to provide managerially oriented arguments regarding the linkages between the achievement of operations-related goals and decisions related to horizontal business relationships. Specifically, we address the following research question: Does a linkage exist between production and operations objectives and the decisions a company makes about horizontal agreements, particularly horizontal governance mode choice? To answer this research question, we develop literature-based hypotheses and c…

Simulation analysis of cold chain performance based on time–temperature data

2011

Perishable goods are a fundamental source of revenue for the retail sector; their management, however, constitutes a severe challenge for retailers and supply chain partners. A significant cost in particular is the fraction of products perished through the supply chain, which also constitutes an ethical and environmental concern. Supply chain organisation and operative characteristics have a significant influence on this matter, as in fact ensuring suitable temperature conditions for the stock-keeping units throughout the supply chain is mandatory for perishable products. Recent developments in sensing and communication technologies allow detailed monitoring and control of cold chain; howev…

Supported iridium catalysts for the total oxidation of short chain alkanes and their mixtures: Influence of the support

2021

13 figures, 3 tables.-- Supplementary information available.-- © 2020. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/

Multiscale analyses and characterizations of surface topographies

2018

International audience; This work studies multiscale analyses and characterizations of surface topographies from the engineering and scientific literature with an emphasis on production engineering research and design. It highlights methods that provide strong correlations between topographies and performance or topographies and processes, and methods that can confidently discriminate topographies that were processed or that perform differently. These methods have commonalities in geometric characterizations at certain scales, which are observable with statistics and measurements. It also develops a semantic and theoretical framework and proposes a new system for organizing and designating …

Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts

2006

Abstract Significant progress has already been achieved in green manufacturing including dry and hard, often high-speed, machining technologies. For instance, the demand for higher productivity has resulted in the wider application of ceramic and PCBN tools with special multi-radii (wiper) geometry. This paper reports some important characteristics of the surface roughness produced in the turning of a hardened low-chromium alloy steel using mixed alumina–titanium carbon (TiC) ceramic cutting tools equipped with both conventional and wiper inserts. The characteristic geometrical features of surfaces obtained in both these turning operations have been assessed by means of representative two-d…