Search results for "ULTRASOUND"
showing 10 items of 1259 documents
Numerical study for a new methodology of flaws detection in train axles
2013
Train loads and travel speeds have increased over time, requiring more efficient non-destructive inspection methods. Railway axles are critical elements; despite being designed to last more than 20 years several cases of premature failure have been recorded. Train axles are inspected regularly, but the limits associated to the traditional inspection technologies create a growing interest towards new solutions. Here a novel non-destructive inspection method of in-service axles based on non-contact data collection is presented. The propagation of surface waves, generated by a thermo-elastic laser source, is investigated using a finite element method based on dynamic explicit integration. Coup…
Interactive multiobjective optimization for anatomy-based three-dimensional HDR brachytherapy.
2010
In this paper, we present an anatomy-based three-dimensional dose optimization approach for HDR brachytherapy using interactive multiobjective optimization (IMOO). In brachytherapy, the goals are to irradiate a tumor without causing damage to healthy tissue. These goals are often conflicting, i.e. when one target is optimized the other will suffer, and the solution is a compromise between them. IMOO is capable of handling multiple and strongly conflicting objectives in a convenient way. With the IMOO approach, a treatment planner’s knowledge is used to direct the optimization process. Thus, the weaknesses of widely used optimization techniques (e.g. defining weights, computational burden an…
Photo-acoustic excitation and optical detection of fundamental flexural guided wave in coated bone phantoms.
2013
Abstract Photo-acoustic (PA) imaging was combined with skeletal quantitative ultrasound (QUS) for assessment of human long bones. This approach permitted low-frequency excitation and detection of ultrasound so as to efficiently receive the thickness-sensitive fundamental flexural guided wave (FFGW) through a coating of soft tissue. The method was tested on seven axisymmetric bone phantoms, whose 1- to 5-mm wall thickness and 16-mm diameter mimicked those of the human radius. Phantoms were made of a composite material and coated with a 2.5- to 7.5-mm layer of soft material that mimicked soft tissue. Ultrasound was excited with a pulsed Nd:YAG laser at 1064-nm wavelength and received on the s…
Assessment of the cortical bone thickness using ultrasonic guided waves: Modelling and in vitro study
2007
Determination of cortical bone thickness is warranted, e.g., for assessing the level of endosteal resorption in osteoporosis or other bone pathologies. We have shown previously that the velocity of the fundamental antisymmetric (or flexural) guided wave, measured for bone phantoms and bones in vitro, correlates with the cortical thickness significantly better than those by other axial ultrasound methods. In addition, we have introduced an inversion scheme based on guided wave theory, group velocity filtering and 2-D fast Fourier transform, for determination of cortical thickness from the measured velocity of guided waves. In this study, the method was validated for tubular structures by usi…
Thickness sensitivity of ultrasound velocity in long bone phantoms
2004
One approach to bone disease diagnosis such as osteoporosis is to measure the velocity of ultrasound propagating axially along long bones. In this study, the variation in velocity as a function of radial position was assessed using two polyvinyl chloride (PVC) bone phantoms with cross-sectional geometry similar to the human tibia but differing in medullary cavity diameter. Two ultrasonometers were used: these were a commercial device operating at a relatively high frequency (HF) of 1.25 MHz and a prototype low frequency (LF) device operating at approximately 200 kHz. The LF measurements showed a larger variation with radial position, with changes in velocity of up to 20% occurring around th…
Measuring guided waves in long bones: Modeling and experiments in free and immersed plates
2005
Guided waves, consistent with the A0 Lamb mode, have previously been observed in bone phantoms and human long bones. Reported velocity measurements relied on line fitting of the observed wave fronts. Such an approach has limited ability to assess dispersion and is affected by interference by other wave modes. For a more robust identification of modes and determination of phase velocities, signal processing techniques using the fast Fourier transform (FFT) were investigated. The limitations of FFT because of spatial resolution were addressed to improve the precision of the measured modes. An inversion scheme was developed for determining the plate thickness from the measured velocity. Experi…
Determination of Bubble Size Distribution Using Ultrasound Array Imaging
2020
In this article, ultrasonic phased arrays are deployed as an imaging tool for industrial process analysis. Such arrays are typically used for sonar, medical diagnosis, and nondestructive testing; however, they have not yet been applied to industrial process analysis. The precise positioning of array elements and high frequencies possible with this technology mean that highly focused images can be generated, which cannot currently be achieved using ultrasound tomography. This article aims to highlight the potential of this technology for the measurement of bubble size distribution (BSD) and to demonstrate its application to both intrusive and noninvasive process measurements. Ultrasound imag…
Phonon contribution to the absorption of ultrasound in amorphous solids at moderately low temperatures
1998
Abstract Sound absorbtion in amorphous solids is considered to be due to the scattering of sound waves from the thermal phonons. It is shown that the dependence of the absorption coefficient on the temperature displays a maximum in the interval 10≲T≲100 K . The frequency dependence of the absorption coefficient is investigated. Numerical calculations for amorphous Mg and Zn illustrate the theoretical results.
Solvent-tuned ultrasonic synthesis of 2D coordination polymer nanostructures and flakes
2021
Highlights • Combined ultrasound and solvent assisted synthesis of 2D coordination polymers. • Role of interstitial solvent molecules in the delamination of 2D-CPs. • Influence of the sonication time in delamination and nanostructuration processes. • Morphological and supramolecular transformations in 2D-CPs.
Photoactivity under visible light of metal loaded TiO2 catalysts prepared by low frequency ultrasound treatment
2017
Abstract Visible-light responsive bare and metal loaded (Pt, Ag, Rh, Pd) TiO 2 photocatalysts were prepared by using a simple ultrasound treatment. This method induced bulk oxygen deficiency resulting in a narrowing bandgap (from 3.18 to 3.04 eV) and in visible light absorption. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), BET specific surface area (SSA) and pore size distribution (PSD), UV–vis diffuse reflectance spectroscopy (DRS), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity of the samples was evaluated by using the 4-nitrophenol oxidation reaction and the photocatalytic oxidation of glucose w…