Search results for "Ultrasonic sensor"
showing 10 items of 139 documents
Comparison of three ultrasonic axial transmission methods for bone assessment.
2005
Abstract This study compared three approaches to bone assessment using ultrasonic axial transmission. In 41 fresh human radii, velocity of the first arriving signal was measured with a commercial device (Sunlight Omnisense ™ ) operating at 1.25 MHz, a prototype based on 1-MHz bidirectional axial transmission and a low-frequency (200 kHz) prototype, also measuring the velocity of a slower wave. Cortical and trabecular bone mineral density, cortical thickness and cross-sectional area were determined by peripheral quantitative computed tomography. Significant but modest correlation between velocities reflects differences in the nature of the propagating waves and methodological differences. Of…
High-speed rotational angioplasty-induced echo contrast in vivo and in vitro optical analysis
1992
High-speed rotational angioplasty is being evaluated as an alternative interventional device for the endovascular treatment of chronic coronary occlusions. It has been postulated that this type of angioplasty device may produce particulate debris or cavitations that induce myocardial ischemia. To determine the clinical presence of myocardial ischemia during rotational angioplasty, echocardiographic monitoring for wall motion abnormalities was performed in 9 patients undergoing rotational atheroablation using the Auth Rotablator for 10-sec intervals at 150,000 and 170,000 rpm. No wall motion abnormalities were detected in 5 patients evaluated with transesophageal echocardiography or in 4 pat…
Numerical study for a new methodology of flaws detection in train axles
2013
Train loads and travel speeds have increased over time, requiring more efficient non-destructive inspection methods. Railway axles are critical elements; despite being designed to last more than 20 years several cases of premature failure have been recorded. Train axles are inspected regularly, but the limits associated to the traditional inspection technologies create a growing interest towards new solutions. Here a novel non-destructive inspection method of in-service axles based on non-contact data collection is presented. The propagation of surface waves, generated by a thermo-elastic laser source, is investigated using a finite element method based on dynamic explicit integration. Coup…
Photo-acoustic excitation and optical detection of fundamental flexural guided wave in coated bone phantoms.
2013
Abstract Photo-acoustic (PA) imaging was combined with skeletal quantitative ultrasound (QUS) for assessment of human long bones. This approach permitted low-frequency excitation and detection of ultrasound so as to efficiently receive the thickness-sensitive fundamental flexural guided wave (FFGW) through a coating of soft tissue. The method was tested on seven axisymmetric bone phantoms, whose 1- to 5-mm wall thickness and 16-mm diameter mimicked those of the human radius. Phantoms were made of a composite material and coated with a 2.5- to 7.5-mm layer of soft material that mimicked soft tissue. Ultrasound was excited with a pulsed Nd:YAG laser at 1064-nm wavelength and received on the s…
Assessment of the cortical bone thickness using ultrasonic guided waves: Modelling and in vitro study
2007
Determination of cortical bone thickness is warranted, e.g., for assessing the level of endosteal resorption in osteoporosis or other bone pathologies. We have shown previously that the velocity of the fundamental antisymmetric (or flexural) guided wave, measured for bone phantoms and bones in vitro, correlates with the cortical thickness significantly better than those by other axial ultrasound methods. In addition, we have introduced an inversion scheme based on guided wave theory, group velocity filtering and 2-D fast Fourier transform, for determination of cortical thickness from the measured velocity of guided waves. In this study, the method was validated for tubular structures by usi…
Determination of Bubble Size Distribution Using Ultrasound Array Imaging
2020
In this article, ultrasonic phased arrays are deployed as an imaging tool for industrial process analysis. Such arrays are typically used for sonar, medical diagnosis, and nondestructive testing; however, they have not yet been applied to industrial process analysis. The precise positioning of array elements and high frequencies possible with this technology mean that highly focused images can be generated, which cannot currently be achieved using ultrasound tomography. This article aims to highlight the potential of this technology for the measurement of bubble size distribution (BSD) and to demonstrate its application to both intrusive and noninvasive process measurements. Ultrasound imag…
Application of low intensity ultrasonics to cheese manufacturing processes.
2002
Ultrasound has been used to non-destructively assess the quality of many foods such as meat, fish, vegetables and dairy products. This paper addresses the applications of low intensity ultrasonics in the cheese manufacturing processes and highlights the areas where ultrasonics could be successfully implemented in the future. The decrease of ultrasonic attenuation during the renneting process can be used to determine the optimum cut time for cheese making. The ultrasonic velocity increases during maturation for those types of cheese that become harder during this manufacturing stage, thus being an indicator of the maturity degree. Moreover, ultrasonic measurements could be linked to sensory …
Defect characterization in Al welded joints by non-contact Lamb wave technique
2006
Abstract The use of air-coupled sensors to detect flaws in Al welded joints and the advantage of Lamb wave for their characterization has been proved. Ultrasonic waves were generated by a pulsed laser and by contact angle-beam transducer, and received by an air-coupled capacitive transducer. Laser-based configuration was used to quickly locate the defect, whereas the angle-beam contact probe configuration to characterize it thanks to the dispersive behavior of Lamb waves. Guided waves allow inspection of the complete thickness with only one scan, permitting to detect and to size both internal and surface defects; their high flexibility in the measurement is due to the various parameters cha…
Laser ultrasonics for defect evaluation on coated railway axles
2020
Abstract This scientific paper focuses on the application of an advanced non-destructive technique for an effective inspection of railway axles. The method pertains to ultrasonic techniques, which are widely used in the railway field. The experimental investigation was carried out on simulated defects tooled near the cross section reduction of the axle, in order to simulate fatigue cracks which, due to notch effect, can trigger crack propagation and axle failure. The aim of this research activity is to evaluate how efficiently the proposed technique detects defects and to verify its applicability to axles with a black coating for protection. In view of the experimental setup, comprising a p…
Theoretical and experimental contributions on ultrasonic contactless examination of underground pipes through which pressurized fluids circulate
2019
Abstract In any civil or industrial construction, there are many embedded pipelines through which pressurized fluids or gases are circulate and which, over time, are subject to corrosion. Examination and monitoring of corrosion/erosion process in order to determine the service life of pipelines through which fluids circulate at different temperatures and / or pressures is a particularly important task for both the designer and the owner because knowledge of “health status” of these in time is extremely. On-site ultrasound control of wall thickness is based on simple propagation time measurements and is typically used to evaluate corrosion and erosion. The paper presents a non-destructive co…