Search results for "VOLTAGE"
showing 10 items of 934 documents
Fullerene imposed high open-circuit voltage in efficient perovskite based solar cells
2016
Five different commercially available fullerenes are evaluated as hole blocking/electron transporting materials in p–i–n methylammonium lead iodide perovskite solar cells using a vacuum deposited perovskite absorber layer. A significant enhancement of the solar cell performance can be obtained by selecting a suitable fullerene derivative. Open-circuit voltages as high as 1.11 volts are obtained leading to a power conversion efficiency of 14.6%.
Meniscus coated high open-circuit voltage bi-layer solar cells
2012
Neat bi-layer solar cells of a fullerene acceptor and a cyanine dye donor were prepared using meniscus coating. Meniscus coating is very material efficient and leads to high quality pinhole-free films. The cells exhibit high open circuit voltages of 1 volt, only 0.8 eV below the band gap of the cyanine dye. This is one of the smallest differences reported for organic solar cells and illustrates an almost optimal donor-acceptor energy level alignment.
Influence of the intermediate density-of-states occupancy on open-circuit voltage of bulk heterojunction solar cells with different fullerene accepto…
2010
Electron density of states (DOS) and recombination kinetics of bulk heterojunction solar cells consisting of a poly(3-hexylthiophene) (P3HT) donor and two fullerene acceptors, either [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) or 4,4′-dihexyloxydiphenylmethano[60]fullerene (DPM6), have been determined by means of impedance spectroscopy. The observed difference of 125 mV in the output open-circuit voltage is attributed to significant differences of the occupancy of the DOS in both fullerenes. Whereas DPM6 exhibits a full occupation of the electronic band, occupancy is restricted to the tail of the DOS in the case of PCBM-based devices, implying a higher rise of the Fermi level in the D…
Voltage-controlled current loops with nanofluidic diodes electrically coupled to solid state capacitors
2016
[EN] We describe experimentally and theoretically voltage-controlled current loops obtained with nanofluidic diodes immersed in aqueous salt solutions. The coupling of these soft matter diodes with conventional electronic elements such as capacitors permits simple equivalent circuits which show electrical properties reminiscent of a resistor with memory. Different conductance levels can be reproducibly achieved under a wide range of experimental conditions (input voltage amplitudes and frequencies, load capacitances, electrolyte concentrations, and single pore and multipore membranes) by electrically coupling two types of passive components: the nanopores (ionics) and the capacitors (electr…
High-voltage measurements on the 5 ppm relative uncertainty level with collinear laser spectroscopy
2018
We present the results of high-voltage collinear laser spectroscopy measurements on the 5 ppm relative uncertainty level using a pump and probe scheme at the transition of involving the metastable state. With two-stage laser interaction and a reference measurement we can eliminate systematic effects such as differences in the contact potentials due to different electrode materials and thermoelectric voltages, and the unknown starting potential of the ions in the ion source. Voltage measurements were performed between −5 kV and −19 kV and parallel measurements with stable high-voltage dividers calibrated to 5 ppm relative uncertainty were used as a reference. Our measurements are compatible …
Design and experimental validation of a high voltage ratio DC/DC converter for proton exchange membrane electrolyzer applications
2019
Abstract This paper deals with hydrogen production via water electrolysis, which is considered the most attractive and promising solution. Specifically, the use of renewable energy sources, such as wind electric power generators, is hypothesized for supplying the electrolyzer, aiming to strongly reduce the environmental impact. In particular, micro-wind energy conversion systems (μWECSs) are attractive for their low cost and easy installation. In order to interface the μWECS and the electrolyzer, suitable power conditioning systems such as step-down DC-DC converters are mandatory. However, due to the requested high conversion ratio between the DC bus grid, i.e. the output of a three-phase d…
Using Pulse Density Modulation to Improve the Efficiency of IGBT Inverters in Induction Heating Applications
2007
This paper analyses a high power (50 kW), high frequency (150 kHz) voltage fed inverter with a series resonant load circuit for industrial induction heating applications which is characterized by a full bridge inverter made with IGBT and the power control based on pulse density modulation (PDM). This power control strategy allows that the inverter works close to the resonance frequency for all output power levels. In this situation zero-voltage switching (ZVS) and zero-current switching (ZCS) conditions are performed and the switching losses are minimized. The results are verified experimentally using a prototype for induction hardening applications. A comparative study between the PDM and …
First experiments with gasdynamic ion source in CW mode.
2016
A new type of ECR ion source—a gasdynamic ECR ion source—has been recently developed at the Institute of Applied Physics. The main advantages of such device are extremely high ion beam current with a current density up to 600–700 emA/cm2 in combination with low emittance, i.e., normalized RMS emittance below 0.1 π mm mrad. Previous investigations were carried out in pulsed operation with 37.5 or 75 GHz gyrotron radiation with power up to 100 kW at SMIS 37 experimental facility. The present work demonstrates the first experience of operating the gasdynamic ECR ion source in CW mode. A test bench of SMIS 24 facility has been developed at IAP RAS. 24 GHz radiation of CW gyrotron was used for p…
How the formation of interfacial charge causes hysteresis in perovskite solar cells
2018
In this study, we discuss the underlying mechanism of the current-voltage hysteresis in a hybrid lead-halide perovskite solar cell. We have developed a method based on Kelvin probe force microscopy that enables mapping charge redistribution in an operating device upon a voltage- or light pulse with sub-millisecond resolution. We observed the formation of a localized interfacial charge at the anode interface, which screened most of the electric field in the cell. The formation of this charge happened within 10 ms after applying a forward voltage to the device. After switching off the forward voltage, however, these interfacial charges were stable for over 500 ms and created a reverse electri…
High voltage stabilisation for an on-line isotope separator
1981
Abstract Stabilisation for a high voltage generator up to 60 kV has been developed. The voltage is stable within ±0.1 V. This allows the very accurate acceleration of charged particles.