Search results for "Vis"
showing 10 items of 21379 documents
Optimization of 3-DOF Parallel Motion Devices for Low-Cost Vehicle Simulators
2017
Motion generation systems are becoming increasingly important in certain Virtual Reality (VR) applications, such as vehicle simulators. This paper deals with the analysis of the Inverse Kinematics (IK) and the reachable workspace of a three-degrees-of-freedom (3-DOF) parallel manipulator, proposing different transformations and optimizations in order to simplify its use with Motion Cueing Algorithms (MCA) for self-motion generation in VR simulators. The proposed analysis and improvements are performed on a 3-DOF heave-pitch-roll manipulator with rotational motors, commonly used for low-cost motion-based commercial simulators. The analysis has been empirically validated against a real 3-DOF …
SiC Based Latching Current Limiter for High Voltage Space Power Distribution Systems
2018
This study presents a novel Latching Current Limiter topology, based on a N-channel Silicon Carbide (SiC) MOSFET as the main switching element. The design has been carried out using only discrete components, without digital controllers. This design has been validated by simulation and with a prototype. Tests have been performed at 1000V, modifying the limitation times, current-limiting values and eventually checking the proper operation of the system.
Regarding the influence of the particle size of crumb rubber from waste rubber on the physical and mechanical characteristics of reclaimed rubber
2017
Thus, at present, a large amount of rubber waste cannot be higher harnessed due to recovery technologies used. Also, the requirements for new products of rubber worldwide are greater than the production capacity and the availability of raw materials. To offset this balance is necessary to improve technologies for recycling waste rubber so to can get regenerated rubber with the best mechanical physical characteristics. The main technology for obtaining the regenerated rubber is based on the rubber waste shredding and making the powder, so that it can be carried out de-vulcanization in autoclave. All the time it was monitored as the de-vulcanization process to be as economical and less pollut…
Flow measurement using circular portable flume
2018
Abstract The circular portable flume is a simple device to measure discharge in circular drainage networks. Since the unit can be easily installed and removed, it is helpful in water distribution measurement and management. First in this paper the available studies are reviewed for highlighting the effect of both the contraction ratio and the flume slope on the stage-discharge relationship. Then the Buckingham's Theorem of the dimensional analysis and the self-similarity theory are used to deduce the stage-discharge curve of the circular flume. The new theoretical stage-discharge equation is calibrated by the literature available experimental data and those obtained in this experimental inv…
Dynamic Design Intents Capture with Formal Ontology and Perdurants Object Concept for Collaborative Product Design
2016
Loss of design intents and related information throughout the lifecycle of products are common. Capturing design intents of an assembly, which include a temporal (dynamic) stages, is even harder. This research work aims to enhance the spatiotemporal mereotopology (STM) based ontology in tune with the contemporary efforts in this research domain. The main idea with such STM ontology is to capture dynamic design intents and develop an integrated data translation framework from Computer Aided Design (CAD) system to a visualization system. This integration framework is intended to enhance design sharing in a collaborative environment. In this paper, the framework is demonstrated with a simple m…
LMI-based 2D-3D Registration: from Uncalibrated Images to Euclidean Scene
2015
International audience; This paper investigates the problem of registering a scanned scene, represented by 3D Euclidean point coordinates , and two or more uncalibrated cameras. An unknown subset of the scanned points have their image projections detected and matched across images. The proposed approach assumes the cameras only known in some arbitrary projective frame and no calibration or autocalibration is required. The devised solution is based on a Linear Matrix Inequality (LMI) framework that allows simultaneously estimating the projective transformation relating the cameras to the scene and establishing 2D-3D correspondences without triangulating image points. The proposed LMI framewo…
Adaptive Backstepping Control of Nonlinear Uncertain Systems With Quantized States
2019
This paper investigates the stabilization problem for uncertain nonlinear systems with quantized states. All states in the system are quantized by a static bounded quantizer, including uniform quantizer, hysteresis-uniform quantizer, and logarithmic-uniform quantizer as examples. An adaptive backstepping-based control algorithm, which can handle discontinuity, resulted from the state quantization and a new approach to stability analysis are developed by constructing a new compensation scheme for the effects of the state quantization. Besides showing the global ultimate boundedness of the system, the stabilization error performance is also established and can be improved by appropriately adj…
Making Industrial Robots Smarter with Adaptive Reasoning and Autonomous Thinking for Real-Time Tasks in Dynamic Environments: A Case Study
2018
In order to extend the abilities of current robots in industrial applications towards more autonomous and flexible manufacturing, this work presents an integrated system comprising real-time sensing, path-planning and control of industrial robots to provide them with adaptive reasoning, autonomous thinking and environment interaction under dynamic and challenging conditions. The developed system consists of an intelligent motion planner for a 6 degrees-of-freedom robotic manipulator, which performs pick-and-place tasks according to an optimized path computed in real-time while avoiding a moving obstacle in the workspace. This moving obstacle is tracked by a sensing strategy based on ma-chin…
Mechanical and metallurgical characterization of AA6082-T6 sheet-bulk joints produced through a linear friction welding based approach
2020
In the last decades, new flexible manufacturing processes have been developed to face the demands, by many industrial fields, for highly customized complex functional parts. The peculiar design of these components often overcomes conventional sheet metal and bulk metal forming processes capabilities. In order to face this issue, new hybrid techniques, capable of exploit key advantages of different processes, have to be developed. In this study, a method to obtain sheet-bulk joints, based on the Linear Friction Welding process, is proposed. The feasibility of the technique was investigated through an experimental campaign carried out with varying pressure and oscillation frequency using AA60…
UJI RobInLab's approach to the Amazon Robotics Challenge 2017
2017
This paper describes the approach taken by the team from the Robotic Intelligence Laboratory at Jaume I University to the Amazon Robotics Challenge 2017. The goal of the challenge is to automate pick and place operations in unstructured environments, specifically the shelves in an Amazon warehouse. RobInLab's approach is based on a Baxter Research robot and a customized storage system. The system's modular architecture, based on ROS, allows communication between two computers, two Arduinos and the Baxter. It integrates 9 hardware components along with 10 different algorithms to accomplish the pick and stow tasks. We describe the main components and pipelines of the system, along with some e…