Search results for "Witch"
showing 10 items of 542 documents
Electromechanical properties of a disc‐type salient‐pole brushless DC motor with different pole numbers
2003
A brushless, permanent magnet, three‐phase disc‐type salient‐pole DC motor with co‐axial flux in the stator is considered. Electromechanical properties of a basic eight‐pole motor are compared with those for a 16‐pole one of the same volume, in order to contrast the two potential candidates for variable‐speed, low‐cost drives. As a basis of the comparative analysis, 3D FEM magnetic field modelling and circuit analysis considering an electronic commutator are employed. Increasing the number of poles results in unfavourable raising in the switching frequency. The eight‐pole motor construction has been shown in simulations to have higher efficiency and lower power losses than its 16‐pole count…
Optical flip-flop memory and data packet switching operation based on polarization bistability in a telecommunication optical fiber
2013
We report the experimental observation of bistability and hysteresis phenomena of the polarization signal in a telecommunication optical fiber. This process occurs in a counterpropagating configuration in which the optical beam nonlinearly interacts with its own Bragg-reflected replica at the fiber output. The proof of principle of optical flip–flop memory and 10 Gbit/s routing operation is also reported based on this polarization bistability. Finally, we also provide a general physical understanding of this behavior on the basis of a geometrical analysis of an effective model of the dynamics. Good quantitative agreement between theory and experiment is obtained.
Switching synchronization in one-dimensional memristive networks: An exact solution.
2017
We study a switching synchronization phenomenon taking place in one-dimensional memristive networks when the memristors switch from the high- to low-resistance state. It is assumed that the distributions of threshold voltages and switching rates of memristors are arbitrary. Using the Laplace transform, a set of nonlinear equations describing the memristors dynamics is solved exactly, without any approximations. The time dependencies of memristances are found, and it is shown that the voltage falls across memristors are proportional to their threshold voltages. A compact expression for the network switching time is derived.
The Performance of Belle II Data Acquisition System in the First Physics Run
2019
The Belle II experiment is a new generation B-factory experiment at KEK in Japan aiming at the search for New Physics in a huge sample of B-meson dacays. The commissioning of the SuperKEKB accelerator was started in 2017 (Phase 1), and then a pilot run with outer detectors was performed in 2018 (Phase 2). From March this year, an operation with the full detector has been started for the physics data taking (Phase 3). The Belle II data acquisiton system (DAQ) is now fully working in the Phase 3 run. The system consists of the trigger timing distribution system, the common readout modules (COPPER) with the unified optical data link to the detector front end, the readout PCs and the network sw…
The metalloproteinase-disintegrin ADAM10 is exclusively expressed by type I muscle fibers.
2008
ADAM10 (Kuzbanian) is a member of a recently discovered family of membrane-anchored metalloproteinases with a complex and conserved domain structure. In part, these metalloproteinases have been implicated in muscle formation. Herein the expression pattern of ADAM10 in human skeletal muscle was studied. ADAM10 was found to be present in human myoblasts and to be exclusively expressed in type I fibers, suggesting that it may be critical in muscle fiber differentiation.
Platform switching on wide-diameter external hex implants: a finite element analysis.
2012
Objectives: The objective of this work was to use finite element analysis to compare the effect of forces coming to bear on abutments 4.1 or 5.0 mm in diameter connected to a 5.0 mm implant (i.e. with or without platform swit - ching). Study design: A 3D CAD model of a 5 x 11.5 mm external hex implant was developed, complete with a connection screw and either of two abutments, one 4.1 and the other 5 mm in diameter, to assess the influence of two loading conditions, i.e. 200 N loaded either axially or off center on the top of the abutment. Results and conclusions: In the symmetrically loaded models, greater stresses were transmitted to the bone in the area below the neck of the implant in t…
Innovative Computational Approach to Harmonic Mitigation for Seven-level Cascaded H-Bridge Inverters
2020
Low frequency modulation strategies are a good solution to increase the energy conversion efficiency in high power applications. The paper is devoted to presents an innovative way to low order harmonics mitigation for seven-level Cascaded H-Bridge Inverters. In particular, this approach is based on the mitigation of selected harmonics without solve non-linear equations for an extended range of the fundamental amplitude. In fact, in real-Time operation to evaluate the control angles the polynomial equations have been identified. Through circuit simulation analysis in MatLab/PLECS environment, the effectiveness of the harmonic mitigation method has been tested and compared with theoretical re…
A Novel Computational Approach for Harmonic Mitigation in PV Systems with Single-Phase Five-Level CHBMI
2018
In this paper, a novel approach to low order harmonic mitigation in fundamental switching frequency modulation is proposed for high power photovoltaic (PV) applications, without trying to solve the cumbersome non-linear transcendental equations. The proposed method allows for mitigation of the first-five harmonics (third, fifth, seventh, ninth, and eleventh harmonics), to reduce the complexity of the required procedure and to allocate few computational resource in the Field Programmable Gate Array (FPGA) based control board. Therefore, the voltage waveform taken into account is different respect traditional voltage waveform. The same concept, known as “voltage cancelation”, used for single-…
Post extractive implant: evaluation of the critical aspects
2017
Purpose Nowadays, implant supported prosthetic rehabilitation is a reliable procedure to replace compromised or untreatable teeth. The purpose of this review is to explore the concept of post extractive implant and the indications for clinical practice through an analysis of recent studies in the literature. All the main factors that could influence the outcome of this treatment will also be considered. Materials and methods Focusing on the extraction-socket healing time, three different implant insertion protocols have been defined: Immediate implant placement (IIP), Early implant placement (EIP), Delayed implant placement (DIP). The entity of bone remodeling can be associated with differe…
Characterization of inductors in partial saturation for SMPS applications
2017
The exploitation of partially saturated inductors in Switching Mode Power Supply (SMPS) is a key strategy for reducing the size of SMPS and increasing their power density [1]. However an accurate characterization and modellization of each inductor is needed for a correct design and control of the SMPS [2]. Most of inductors' datasheets only indicate the nominal inductance at low current. Anyway, when the inductor is subjected to a higher current, the value of the inductance is lessened. Moreover, inductance meters often actuate their measurements at no or moderate DC bias. In this work we describe the realization of an automated test bench (Fig. 1) for characterizing an inductor under varia…