Search results for "Wood"
showing 10 items of 818 documents
Levels, fingerprint and daily intake of polycyclic aromatic hydrocarbons (PAHs) in bread baked using wood as fuel
2009
Concentrations, fingerprint and daily intake of 16 PAHs in 15 bread samples baked using wood as fuel are examined in this work. Analysis was performed by GC/MS after saponification of the samples and clean up of the extract. The total concentration of the 16 analytes varies from 6 to 230 microg/kg on dry weight (d.w.). The better extraction procedure was estimated by analyzing test-samples and using different extraction methods. Additionally, for every analyzed sample, the extraction yield has been determined by the use of surrogate standards. Extraction yields were never less than 77% and in most cases almost 100%. The profiles of PAHs (percentage) are similar for all the analyzed samples …
Chemical composition of lipophilic extractives from grey alder (Alnus incana)
2013
The chemical composition of the lipophilic extractives in the hexane extracts from grey alder bark, knotwood, and cones has been investigated by gas chromatography and gas chromatography-mass spectrometry. The efficiency of two extraction methods was compared. The highest amount of lipophilic extractives (about 9% of o.d. material) was observed in grey alder cone, while the lowest (about 3%) was found in knotwood. The three different morphological parts of alder showed significant differences not only in the content but also in composition of extractives, namely fatty acids, triglycerides, and triterpenes. The main identified compounds were triterpenoids (lupen-3-one, lupeol, betulone, betu…
Lignin from steam‐exploded wood as binder in wood composites
2010
A study demonstrating the approach of zero‐waste technologies, a component of the Zero Emissions concept, and using lignin extracted from steam‐exploded wood as adhesive in hot‐pressed fibre boards and plywood to substitute phenol‐formaldehyde resins is reported. Properties of sample boards containing different amount of lignin adhesive are compared between themselves and with the EU standards for fibre boards. A strong correlation of density and form stability under humid conditions with the lignin content is found. Results of testing mechanical properties of the boards suggest that effect of lignin on mechanical strength depends on the size of particles and hot‐pressing temperature. Steam…
Influence of Welding Time on Tensile-Shear Strength of Linear Friction Welded Birch (Betula pendula L.) Wood
2015
Linear friction welding of wood is a bonding process applied to wood and during which a stiff bond line is formed by the softening and rehardening of wood components to form a composite material composed mainly of wood fibres embedded in a modified lignin matrix. Unfortunately, the bonds tend to spontaneously delaminate or lose their strength when exposed to moist conditions. Some approaches were previously applied to overcome this problem, but so far a suitable solution has not been found. This paper presents results of applying post-welding thermal modification to reduce the moisture sensitivity of welded wood. The experiments included welding of birch wood, thermal modification under sup…
Chlorinated dioxins and dibenzothiophenes in fly ash samples from combustion of peat, wood chips, refuse derived fuels and liquid packaging boards
1995
Abstract Peat, wood chips, refuse derived fuel and liquid packaging board in different combinations were burned at a temperature of at least 850 °C. Fly ash samples from these combustions were analyzed for polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzothiophenes (PCDBTs) by high resolution GC/MS. The concentrations of tri- and tetrachlorodibenzothiophenes and tri-, tetra- and pentachlorodioxins were highest when mixtures of wood chips and refuse derived fuel (RDF) were burned. The fly ash from the combustion of pure peat pellets did not contain any polychlorinated dibenzothiophenes. When wood chips and RDF were burned the concentrations of chlorinated compounds in fly…
Multivariate Correlation between Analytical Data for Various Organics Dissolved during Autohydrolysis of Silver Birch (Betula pendula) Chips and Trea…
2014
Autohydrolysis pre-treatments were performed for the production of hemicellulose-rich autohydrolysates from silver birch (Betula pendula) chips prior to chemical pulping. Pre-treatment conditions were varied with respect to time (from 30 to 120 min) and temperature (130 and 150 °C), covering a P-factor range from 10 to 238. Hydrolysates were analyzed in terms of carbohydrates, lignin, volatile organic acids, and furanoic compounds. The analytical data were subjected to various chemometric techniques to establish the relationships between dissolved organic components, hardwood and softwood used in the experiments, and applied pre-treatment conditions. Using this method, differences between t…
Extractability of metals and ecotoxicity of soils from two old wood impregnation sites in Finland
2003
Abstract Four metal-contaminated soil samples were classified using physical methods, extracted by selective extraction procedures and analyzed for chemical concentrations. De-ionized water, 0.01 mol/l barium chloride, 1 mol/l ammonium acetate and concentrated nitric acid were used as extraction solutions. Ecotoxicity of water extracts and soil samples was analyzed in order to describe the bioavailability of the contaminants. Samples from old wood impregnation plants contained high amounts of As, Cu, Cr and Zn, which originated from chromated copper arsenate, ammoniacal copper–zinc arsenate, and ammoniacal copper quaternary compound. Total As concentrations of the heavily contaminated sampl…
Sulphate Removal from Water by Carbon Residue from Biomass Gasification: Effect of Chemical Modification Methods on Sulphate Removal Efficiency
2016
Sulphate removal from mine water is a problem because traditional chemical precipitation does not remove all sulphates. In addition, it creates lime sediment as a secondary waste. Therefore, an inexpensive and environmental-friendly sulphate removal method is needed in addition to precipitation. In this study, carbon residues from a wood gasification process were repurposed as precursors to a suitable sorbent for SO42- ion removal. The raw material was modified using ZnCl2, BaCl2, CaCl2, FeCl3, or FeCl2. Carbon residues modified with FeCl3 were selected for further consideration because the removal efficiency toward sulphate was the highest. Batch sorption experiments were performed to eval…
Exposure to bioaerosols and noise at a Finnish dry waste treatment plant
2004
Repeated measurements were carried out during two different campaigns between 1998 and 2001 to assess the occupational hygiene at a Finnish dry waste treatment plant. The analytical determinations were done in four different places within the processing hall of the plant: near a conveyor belt, near a jigger screen, near an after-crusher and near a bailer. Measurements were also carried out in a coffee room for employees. Concentrations of bacteria, fungi and actinomycetes were determined by two methods (six-stage impactor and Camnea method) and levels of endotoxins, dust and noise were also investigated. High concentrations of microbes and endotoxins and the noise level were found to be a …
OVERVIEW OF ANALYTICAL PROCEDURES FOR FATTY AND RESIN ACIDS IN THE PAPERMAKING PROCESS
2012
This review describes the role of wood extractives, especially fatty and resin acids, in papermaking, as well as the importance of their removal from process waters. One of the main aims is also to illustrate versatile analysis methods for this purpose and highlight recent developments in corresponding applications. Most of the current methods require time-consuming and laborious sample pretreatment procedures prior to gas chromatography coupled either with flame ionization or mass selective detection. However, some faster, even online techniques with minimum sample pretreatment, are also available, mainly including high performance liquid chromatography coupled with mass spectrometry. The …