Search results for "Work function"
showing 10 items of 42 documents
Measurements of tunneling conduction to carbon nanotubes and its sensitivity to oxygen gas
2012
We have measured the conductive properties of junctions between carbon nanotubes (CNT) and non-noble metals $M$ ($M$ = Al, Ti, Nb), which are separated by the native oxide (${M}_{\mathit{OX}}$) of the metal. Reproducible and asymmetric current-voltage characteristics were obtained from Ti/Ti${}_{\mathit{OX}}$/CNT and Nb/Nb${}_{\mathit{OX}}$/CNT junctions, while Al/Al${}_{\mathit{OX}}$/CNT exhibited no current until breakdown, which is attributed to the larger bandgap of Al${}_{\mathit{OX}}$. The conduction in the Ti- and Nb-based junctions is not due to direct tunneling since they exhibit strong temperature dependence. The presence of oxygen is shown to drastically, but reversibly, modify t…
Kelvin probe force microscopy studies of the charge effects upon adsorption of carbon nanotubes and C 60 fullerenes on hydrogen-terminated diamond
2018
Hydrogen-terminated diamond is known for its unusually high surface conductivity that is ascribed to its negative electron affinity. In the presence of acceptor molecules, electrons are expected to transfer from the surface to the acceptor, resulting in p-type surface conductivity. Here, we present Kelvin probe force microscopy (KPFM) measurements on carbon nanotubes and C60 adsorbed onto a hydrogen-terminated diamond(001) surface. A clear reduction in the Kelvin signal is observed at the position of the carbon nanotubes and C60 molecules as compared with the bare, air-exposed surface. This result can be explained by the high positive electron affinity of carbon nanotubes and C60, resulting…
Support work function as a descriptor and predictor for the charge and morphology of deposited Au nanoparticles.
2020
We show, using density functional theory calculations, that the charge, magnetic moment, and morphology of deposited Au nanoclusters can be tuned widely by doping the oxide support with aliovalent cations and anions. As model systems, we have considered Aun (n = 1, 2, or 20) deposited on doped MgO and MgO/Mo supports. The supports have been substitutionally doped with varying concentrations θ of F, Al, N, Na, or Li. At θ = 2.78%, by varying the dopant species, we are able to tune the charge of the Au monomer between −0.84e and +0.21e, the Au dimer between −0.87e and −0.16e, and, most interestingly, Au20 between −3.97e and +0.49e. These ranges can be further extended by varying θ. These chan…
Thin film growth and band lineup of In2O3 on the layered semiconductor InSe
1999
Thin films of the transparent conducting oxide In2O3 have been prepared in ultrahigh vacuum by reactive evaporation of indium. X-ray diffraction, optical, and electrical measurements were used to characterize properties of films deposited on transparent insulating mica substrates under variation of the oxygen pressure. Photoelectron spectroscopy was used to investigate in situ the interface formation between In2O3 and the layered semiconductor InSe. For thick In2O3 films a work function of φ = 4.3 eV and a surface Fermi level position of EF−EV = 3.0 eV is determined, giving an ionization potential IP = 7.3 eV and an electron affinity χ = 3.7 eV. The interface exhibits a type I band alignmen…
Reversible oxidation of WOx and MoOx nano phases
2012
International audience; WOx and MoOx nano phases were prepared on TiO2(1 1 0) surfaces by a CVD procedure consisting of adsorption and decomposition of W(CO)(6) or Mo(CO)(6) precursors followed by annealing under UHV. Metal amount involved in each elaborated sample is in the fractional range from 0.1 to 0.35 equivalent monolayer (eqML) of W or Mo. Evolution of sample stoichiometry as a function of subsequent treatment is followed by valence band and core level photoemission as well as work function measurement. In each case, exposure of samples to molecular oxygen at room temperature induces an increase of sample work function in a range of several tenth of eV. Such a work function change i…
Physical Fundamentals of Biomaterials Surface Electrical Functionalization
2020
This article is focusing on electrical functionalization of biomaterial&rsquo
Capacitance-voltage characteristics of organic light-emitting diodes varying the cathode metal: Implications for interfacial states
2007
Capacitance-voltage $(C\text{\ensuremath{-}}V)$ characteristics of organic light-emitting diodes based on a polyphenylenevinylene have been measured by means of impedance spectroscopy. The effect of the metallic cathode (Au, Ag, Al, Mg, and Ba) was analyzed in the low-frequency region $(2\phantom{\rule{0.3em}{0ex}}\mathrm{Hz})$ of the capacitive response. The $C\text{\ensuremath{-}}V$ curves collapse into a single pattern in the low bias region, and exhibit a dependence on the cathode work function showing a crossover from positive to negative (inductive) values. The voltage corresponding to the onset of the inductive behavior shifts toward higher bias as the cathode work function increases…
High voltage vacuum-processed perovskite solar cells with organic semiconducting interlayers
2020
In perovskite solar cells, the choice of appropriate transport layers and electrodes is of great importance to guarantee efficient charge transport and collection, minimizing recombination losses. The possibility to sequentially process multiple layers by vacuum methods offers a tool to explore the effects of different materials and their combinations on the performance of optoelectronic devices. In this work, the effect of introducing interlayers and altering the electrode work function has been evaluated in fully vacuum-deposited perovskite solar cells. We compared the performance of solar cells employing common electron buffer layers such as bathocuproine (BCP), with other injection mate…
Phosphomolybdic acid as an efficient hole injection material in perovskite optoelectronic devices.
2018
Efficient perovskite devices consist in a perovskite film sandwiched in between charge selective layers, in order to avoid non-radiative recombination. A common metal oxide used as p-type or hole transport layer is molybdenum oxide. MoO3 is of particular interest for its very large work function, which allows it to be used both as an interfacial charge transfer material as well as a dopant for organic semiconductors. However, high quality and high work function MoO3 is typically thermally evaporated in vacuum. An alternative solution-processable high work function material is phosphomolybdic acid (PMA), which is stable, commercially available and environmentally friendly. In this communicat…
Flexible light-emitting electrochemical cells with single-walled carbon nanotube anodes
2016
Abstract In this work, we demonstrate flexible solution processed light emitting electrochemical cells (LECs) which use single-walled carbon nanotubes (SWCNTs) films as the substrate. The SWCNTs were synthesized by an integrated aerosol method and dry-transferred on the plastic substrates at room temperature. The addition of a screen printed poly (3,4-ethylene dioxythiophene) doped with poly (styrene sulfonate) (PEDOT:PSS) film onto the nanostructured electrode further homogenizes the surface and enlarges the work function, enhancing the hole injection into the active layer. By using an efficient phosphorescent ionic transition metal complex (iTMC) as the active material, efficacies up to 9…