Search results for "Young's modulus"
showing 10 items of 74 documents
Layer-dependent mechanical properties and enhanced plasticity in the van der Waals chromium trihalide magnets
2020
The mechanical properties of magnetic materials are instrumental for the development of the magnetoelastic theory and the optimization of strain-modulated magnetic devices. In particular, two-dimensional (2D) magnets hold promise to enlarge these concepts into the realm of low-dimensional physics and ultrathin devices. However, no experimental study on the intrinsic mechanical properties of the archetypal 2D magnet family of the chromium trihalides has thus far been performed. Here, we report the room temperature layer-dependent mechanical properties of atomically thin CrI3 and CrCl3, finding that bilayers of CrI3 and CrCl3 have Young's moduli of 62.1 GPa and 43.4 GPa, with the highest sust…
A preliminary study of hardness and modulus of elasticity in sheep mandibles submitted to distraction osteogenesis and low-level laser therapy
2011
Objectives: To investigate the quality of newly formed bone in sheep mandibles submitted to distraction osteogenesis and low-level laser therapy (LLLT), based on hardness and modulus of elasticity values. The ideal moment for laser application (during the latency/activation period vs. during the bone consolidation period) was also evaluated. Computed tomography imaging was used to assess relapse as a result of early device removal. Study design: Extraoral distraction devices were placed in five sheep so as to achieve 1.5 cm of lengthened bone in 60 days. Distraction devices were removed 50, 40, and 33 days after surgery. Four animals were treated with LLLT, at different times, and one was u…
Prediction of bone mechanical properties using QUS and pQCT: study of the human distal radius.
2007
Abstract The objective was to compare the prediction of bone mechanical properties provided by axial transmission to that provided by peripheral quantitative computed tomography (pQCT) at the distal radius. The distal radius is the location for Colles’ fractures, a common osteoporosis related trauma situation. Measurements of the radial speed of sound were performed using three axial transmission devices: a commercial device (Sunlight Omnisense, 1.25 MHz), a bi-directional axial transmission prototype (1 MHz), both measuring the velocity of the first arriving signal (FAS), and a low frequency (200 kHz) device, measuring the velocity of a slower wave. Co-localized pQCT measurements of bone m…
Definition of diagonal Poisson's ratio and elastic modulus for infill masonry walls
2014
The prediction of the response of infilled frames through the simplified approach of substituting the infill with an equivalent pin-jointed strut is treated. In this framework the results of an experimental study for the mechanical characterization of different types of masonry infills having the aim of estimating strength, Young modulus and Poisson's ratio are presented. Four types of masonry were investigated and subjected to ordinary compressive tests orthogonally to the mortar beds and along the directions of the mortar beds. The experimental campaign confirmed the possibility of using an orthotropic plate model for prediction of the Poisson's ratio and Young modulus along the diagonal …
Effect of areal weight and chemical treatment on the mechanical properties of bidirectional flax fabrics reinforced composites
2010
Abstract In this paper several bidirectional flax fibers, usually used to made curtains, were employed as reinforcement of an epoxy matrix. Four different laminates were made by a vacuum bagging process, with varying both the areal weight and the treatment of the fabric. These structures were mechanically investigated carrying out both tensile and three point flexural tests. In order to evaluate the effect of the identified variables on the mechanical parameters (i.e. Young modulus and maximum stress) a statistical analysis was performed. Finally, by comparing the flax composite with a glass one, the convenience of the replacement of glass fiber was investigated in term of cost, weight and …
Mechanical properties of steel fibre reinforced lightweight concrete with pumice stone or expanded clay aggregates
2001
This paper presents basic information on the mechanical properties of steel fibre-reinforced light-weight concrete, manufactured using pumice stone or expanded clay aggregates. Results are presented for standard compressive tests and indirect tensile tests (splitting tests on cylinder specimens and flexure tests on prismatic beams using a three-point loading arrangement) under monotonically increasing or cyclically varying loads. The influence of steel fibres and aggregate types on modulus of elasticity, compressive and tensile strength and post-peak behaviour is evaluated. Test results show that compressive strength does not change for pumice stone aggregates, while an increase is observed…
Rheological characterization and release properties of inulin-based hydrogels
2012
Abstract In the present study the rheological properties of hydrogels obtained through UV irradiation of an aqueous solution of methacrylated inulin (INUMA) alone or in the presence of four different crosslinkers, have been recorded as a function of irradiation time, at two different wavelengths (320 and 365 nm) and fixed frequency and amplitude by oscillatory experiments. Each hydrogel has been analyzed by measurements of the frequency-dependency of the elastic modulus, G ′, in the linear viscoelastic region. The amount of polymeric chains giving an elastic response has been correlated to the chemical nature of the crosslinker used together with INUMA. Finally the release properties of the…
Hardness and modulus of elasticity of atomic layer deposited Al2O3-ZrO2 nanolaminates and mixtures
2020
This work was funded by the European Regional Development Fund project TK134 “Emerging orders in quantum and nanomaterials”, Estonian Research Agency project PRG4 “Emerging novel phases in strongly frustrated quantum magnets”.
Effects of endodontic treatment on apparent Young’s modulus of human teeth: in vitro study using speckle interferometry
2012
The introduction of new techniques for endodontic procedures requires the analysis of the biomechanical behavior of dental structures. Digital speckle shearing pattern interferometry (DSSPI) is a nondestructive optical measuring technique that allows one to directly quantify deformations in teeth that are subjected to stress. DSSPI technique was applied to measure small deformations caused by flexion in different types of teeth. The test was carried out both before and after endodontic treatment with the ProTaper method in order to evaluate the variation of dental elasticity, taking into the account the type of tooth and the endodontic treatment. The results obtained show that dental elasti…
Microstructure and Mechanical Properties of High-Pressure LixNa1-xTayNb1-yO3Solid Solution Perovskite Ceramics
2012
The effects of the temperature of synthesis and component concentration on microstructure of high-pressure LixNa1-xTayNb1-yO3 solid solution perovskite ceramics (х = 0.12, 0.17; у = 0; у ≥ 0.5) were studied. Original results of elastic properties of high-pressure LixNa1-xTayNb1-yO3 (х = 0.17; 0 ≤ у ≤ 0.5) solid solutions measured by contact probe techniques are reported. The observed decrease of the modulus of elasticity with increasing the sintering temperature of Li0,17Na0,83TayNb1-yO3 solid solutions is assumed to be related to conditions of re-crystallisation of disordered solid solutions at synthesis under high pressure.