Search results for "amber"
showing 10 items of 419 documents
The methane Raman spectrum from 1200 to 5500 cm(-1): A first step toward temperature diagnostic using methane as a probe molecule in combustion syste…
2005
International audience; We present a study of the spontaneous Raman spectra of (CH4)-C-12 from 1200 to 5500 cm(-1) at various temperatures. This study is of interest from a fundamental as well as from a practical point of view with regards to the temperature diagnostic in hydrocarbon combustion. The present investigation shows that the spontaneous (CH4)-C-12 Raman spectra are very sensitive to temperature and that the complexity of methane spectra is not an obstacle to use methane as a probe molecule in laser-diagnostic techniques. Our study consists in determining the polarisability parameters of methane (CH4)-C-12, unknown at the present time, from spontaneous Raman spectra recorded at pr…
The Experimental Validation of a New Thermodynamic Method for TDC Determination
2007
In-cylinder pressure analysis is becoming more and more important both for research and development purpose and for control and diagnosis of internal combustion engines; directly measured by means of a combustion chamber pressure transducers or evaluated by analysing instantaneous engine speed [1,2,3,4], incylinder pressure allows the evaluation of indicated mean effective pressure (IMEP), combustion heat release, combustion phase, friction pressure, etc...It is well known to internal combustion engine researchers that for a right evaluation of these quantities the exact determination of Top Dead Centre (TDC) is of vital importance: a 1° error on TDC determination can lead to evaluation err…
Reduction of low-frequency 1/f noise in Al-AlOx-Al tunnel junctions by thermal annealing
2010
We report that annealing Al-AlOx-Al tunnel junctions in a vacuum chamber at temperature of 400C reduces the characteristic 1/f noise in the junctions, in some cases by an order of magnitude. Both ultra high vacuum and high vacuum fabricated samples demonstrated a significant reduction in the 1/f noise level. Temperature dependence of the noise was studied between 4.2 and 340 Kelvin, with a linear dependence below 100 K, but a faster increase above. The results are consistent with a model where the density of charge trapping two level-systems within the tunneling barrier is reduced by the annealing process.
Design and evaluation of a HDR skin applicator with flattening filter
2008
The purposes of this study are: (i) to design field flattening filters for the Leipzig applicators of 2 and 3 cm of inner diameter with the source traveling parallel to the applicator contact surface, which are accessories of the microSelectron-HDR afterloader (Nucletron, Veenendaal, The Netherlands). These filters, made of tungsten, aim to flatten the heterogeneous dose distribution obtained with the Leipzig applicators. (ii) To estimate the dose rate distributions for these Leipzig+filter applicators by means of the Monte Carlo (MC) method. (iii) To experimentally verify these distributions for prototypes of these new applicators, and (iv) to obtain the correspondence factors to measure t…
Numerical Simulation as a Tool for Design Optimization of Two-Phase Swirl Flow Atomizers
2021
This study aims to analyze the hydrodynamics in two-phase swirl flow conical atomizers. The Euler-Euler model was used for the calculations. Numerical simulations were performed to provide information about the fluid velocity distribution and the atomizer’s internal flow. The numerical calculations confirmed the experimental data. This data was found based on the consistency of the spray angles obtained by both methods. Assuming the correctness of the numerical simulations performed, they can be treated as a tool for further analysis of mass and energy exchange along with the atomizer and optimizing the atomizer’s design depending on the requirements. The influence of the swirl chamber geom…
New prototypes for the isolation of the anodic chambers in microbial fuel cells
2016
This work has been focused on the assessment of new prototypes of MFC in which a more strict separation of the anode and cathode compartments is looked for, in order to attain strict anaerobic conditions in the anode chamber and hence, avoid lack of efficiency due to the prevalence of non-electrogenic competing microorganisms and to optimize composition of the anolyte and catholyte. A cylinder reactor with an inner chamber with graphite bars acting as anodes and the outer one with a stainless steel tube acting as cathode was used in three different configurations and results obtained during lifetests are compared in terms of electricity production, cathode oxygen consumption and anode COD d…
SiPMs coated with TPB: coating protocol and characterization for NEXT
2012
[EN] Silicon photomultipliers (SiPM) are the photon detectors chosen for the tracking readout in NEXT, a neutrinoless \bb decay experiment which uses a high pressure gaseous xenon time projection chamber (TPC). The reconstruction of event track and topology in this gaseous detector is a key handle for background rejection. Among the commercially available sensors that can be used for tracking, SiPMs offer important advantages, mainly high gain, ruggedness, cost-effectiveness and radio-purity. Their main drawback, however, is their non sensitivity in the emission spectrum of the xenon scintillation (peak at 175 nm). This is overcome by coating these sensors with the organic wavelength shifte…
Copper coated carbon fiber reinforced plastics for high and ultra high vacuum applications
2014
We have used copper-coated carbon fiber reinforced plastic (CuCFRP) for the construction of high and ultra-high vacuum recipients. The vacuum performance is found to be comparable to typical stainless steel used for this purpose. In test recipients we have reached pressures of 2E-8 mbar and measured a desorption rate of 1E-11 mbar*liter/s/cm^2; no degradation over time (2 years) has been found. Suitability for baking has been found to depend on the CFRP production process, presumably on the temperature of the autoclave curing. Together with other unique properties of CuCFRP such as low weight and being nearly non-magnetic, this makes it an ideal material for many high-end vacuum application…
Depth-dose measurement corrections for the surface electronic brachytherapy beams of an Esteya® unit: a Monte Carlo study
2020
Abstract Three different correction factors for measurements with the parallel-plate ionization chamber PTW T34013 on the Esteya electronic brachytherapy unit have been investigated. This chamber type is recommended by AAPM TG-253 for depth-dose measurements in the 69.5 kV x-ray beam generated by the Esteya unit. Monte Carlo simulations using the PENELOPE-2018 system were performed to determine the absorbed dose deposited in water and in the chamber sensitive volume at different depths with a Type A uncertainty smaller than 0.1%. Chamber-to-chamber differences have been explored performing measurements using three different chambers. The range of conical applicators available, from 10 to 30…
Laboratory Tests for Assessing the Reliability and Durability of Innovative Cold-Glued 3D Glass Building Subcomponents
2020
The paper shows the results of analyses of the behavior of an innovative subcomponent made of two glass shells and a plastic thermal belt interfaced with a resin-based adhesive, in order to define the plastic material–adhesive combination able to guarantee compliance with the requirements related to mechanical strength, thermoacoustic insulation, dimensional stability, material compatibility, and durability. Two different types of ultraviolet (UV)-curing adhesive were used to establish the best plastic–adhesive combination. A study of the mechanical behavior and the reliability over time of the bonded assembly was conducted by performing accelerated weathering tests and tensile tests on 30 …