Search results for "automatic"
showing 10 items of 730 documents
Review on photovoltaic based active generator
2015
An active generator has the capacity to support frequency control and instantaneous power balance. The grid operator adjusts the power dispatch of generators according to power demand fluctuations. Photovoltaic (PV) based active generators can be used as load following generators in the same manner as other power dispatch generators. This new type of distribution system, based on active generator(s), needs new innovative management and operation strategies for increasing the penetration of intermittent renewable energy systems. The considered PV based active generator has three units, i.e., PV array, battery storage and super capacitor. In this review paper, the management and operation app…
Task scheduling control of BGA solder joint process in flexible manufacturing system
2006
This paper describes an open loop control method of the solder joint process in a rework station for faulty printed circuit board (PCBs) containing electronic components in packages ball grid arrays (BGAs). In particular, a mathematical model describing the solder joint process is, first of all, obtained. Then, the desired thermal profile of the junctions BGA-PCB is determined according to the physical constraints of the rework station framework. The control parameters corresponding to the above desired thermal profile are identified using the above mathematical model. Finally, the open loop control algorithm is implemented on the supervisor interface of the rework station in order to carri…
Dynamic performance enhancement of AC/DC PFC boost converters by means of MRAS observers
2015
Controlling a Power Factor Corrected (PFC) boost converter is not a trivial task, because the higher the dynamic performance, the higher is the input current distortion. On the other hand, recent applications of these converters require fast transients in response to disturbances, such as sudden variations of load power, reference voltage and input voltage. Better performance can be obtained adding a feedforward action to the traditional control scheme, using observers to estimate the input voltage and the output current. However, the actual improvement depends on the dynamic performance of the chosen observers. This paper aims at evaluating the applicability and the performance of differen…
A new approach to the design of a speed-torque-controlled rubber V-belt variator
2005
This paper presents a new model for a torque-speed-sensing rubber V-belt variator. The actuators are of the centrifugal roller kind on the driver side and a helical torque cam plus a compression-torsion spring on the driven side. The equations permit designing the actuator geometry in order to keep the transmissible torque as close as possible to the torque request in the whole operative field. Moreover, a procedure is suggested for the most proper design of an automatic variator of this kind. It permits choosing the required variogram of the transmission, i.e. the matching between the engine and the transmission, and designing the actuators: roller mass, housing shape, contact plate angle…
A parametric study on unbalanced three phase islanded microgrids with inverter interfaced units
2013
In this paper, the solution of the power flow for unbalanced three phase microgrids systems is proposed. The study aims at the integration of inverter interfaced units using the control law used for primary voltage and frequency regulation, so as to take into account possible small variations of these parameters to account for sudden load changes. The proposed study deals with unbalanced systems which is the typical case of small distribution systems and shows how the power losses term varies as the regulators parameters vary as well, thus showing that these are sensitive parameters that could have an important role in optimal management of such systems.
The Use of Accelerometers and Gyroscopes to Estimate Hip and Knee Angles on Gait Analysis
2014
In this paper the performance of a sensor system, which has been developed to estimate hip and knee angles and the beginning of the gait phase, have been investigated. The sensor system consists of accelerometers and gyroscopes. A new algorithm was developed in order to avoid the error accumulation due to the gyroscopes drift and vibrations due to the ground contact at the beginning of the stance phase. The proposed algorithm have been tested and compared to some existing algorithms on over-ground walking trials with a commercial device for assisted gait. The results have shown the good accuracy of the angles estimation, also in high angle rate movement.
Method for designing PI-type fuzzy controllers for induction motor drives
2001
The paper illustrates a new systematic method for designing PI-type fuzzy controllers for direct field-oriented controlled induction motor drives. First, linear and decoupled models expressing the dynamics of speed, rotor flux, direct and inquadrature stator currents are derived using a nonlinear static compensator and choosing convenient input variables. Then, to guide the dynamics of the above quantities, four conventional PI controllers are designed independently, choosing their bandwidths conveniently. Finally, the input and output scale factors of PI-type fuzzy controllers are derived from the conventional PI controller parameters. The whole drive controller also includes a rotor flux …
A Model-Based Control Strategy for Wind Turbines with Asynchronous Generator
2007
In this paper a model based control methodology is described with reference to a wind turbine for production of alternative energy. The mathematical model of a 600 kW wind turbine is taken into account assuming a well defined profile of the rotor blades. A set of reference angular speeds of the asynchronous generator and a set of reference pitch angles of the blade wind turbine are obtained in order to maximize the extracted wind power and to reach equilibrium conditions between the wind-generated torque and the electric torque of the generator. Finally a PID model based controller is designed and then tested by means of simulation experiments.
A Novel Method of Distance Measurement Based on Pulse Position Modulation and Synchronization of Chaotic Signals Using Ultrasonic Radar Systems
2009
This paper deals with a novel method of transmission and receipt of a signal based on both the property of two chaotic systems generating the same chaotic signal when they are synchronized and the property of pulse position modulation (PPM) to be insensitive to the distortions of the transmission channel. The method is discussed in the context of ultrasonic radar systems, in which the transmitter and receiver, which consist of ultrasonic sensors, are near each other, and the received signal consists of the transmitted signal reflected by an obstacle. A reference sinusoidal signal is superimposed to a chaotic signal generated by a master chaotic system, and the whole signal is modulated acco…
Stability and Noises Evaluation of Fuzzy Kalman UAV Navigation System.
2009
In this paper a new Fuzzy/Kalman navigation system for Unmanned Aerial Vehicles (UAV) is presented. A closed loop velocity Fuzzy navigation system is proposed for stabilizing the UAV in a reference trajectory generated dynamically and for obtaining a forward velocity command. The Kalman's filter (KF) is included in the feedback line of the fuzzy control system to filter the internal noise of the sensors and to evaluate the external noise due to possible perturbations of the nominal motion. The efficiency of the navigation system has been shown through experimental tests in a Matlab environment.