Search results for "cfd"

Unité et scissions dans l’histoire de la CGT

2019

National audience; La question de l’unité tient une place particulière dans l’histoire de la CGT dans la mesure où elle est l’exception qui confirme la règle. En dehors des périodes 1895-1921, 1936-39 et 1943-47, la spécificité du syndicalisme confédéré réside dans sa division et son éclatement. Sur plus de 120 ans d’existence, la CGT n’a connu l’unité organique que durant une trentaine d’années (soit ¼ de son histoire). La division, ou le pluralisme si l’on préfère, est en somme la situation « normale » du syndicalisme français.Ce chapitre propose donc de comprendre les raisons et les processus qui ont conduit à cet état de dispersion ; et inversement, d’analyser les facteurs qui ont rendu…

Experimental and fluid dynamic study of continuous supercritical water gasification of glucose

2016

Abstract The supercritical water gasification (SCWG) of glucose as a model compound for H 2 production is studied in term of process development at 25 MPa and 650 °C. Gasification has been investigated using a laboratory scale continuous plant comprising a continuous down flow reactor with a volume of 200 cm 3 , a heat recovery section and pre-heat of the biomass to simulate more closely an industrial design. Feed streams (pure water and glucose solution) are introduced at the top of the vessel and products are extracted from the bottom. The reactor is equipped with various inlet points that allow to modify the inlet position of reacting streams in order to study the effect of stream mixing…

Salbutamol Transport and Deposition in the Upper and Lower Airway with Different Devices in Cats: A Computational Fluid Dynamics Approach

2021

Simple Summary Administration of inhaled salbutamol via metered-dose inhalers can effectively treat bronchoconstriction. Different devices are used for the delivery of this drug in cats, either in the hospital or at home, for long-term treatment. Effective drug administration may depend on the drug delivery device as well as patient cooperation. By using non-invasive computational fluid dynamics techniques, the impact of these devices on the deposition and transport of salbutamol particles in the cat airways was simulated and assessed. The results confirm a variable drug distribution depending on the device used. The percentage of particles reaching the lung was reduced when using spacers a…

A computational aeroelastic framework based on high-order structural models and high-fidelity aerodynamics

2023

A computational framework for high-fidelity static aeroelastic analysis is presented. Aeroelastic analysis traditionally employs a beam stick representation for the structure and potential, inviscid and irrotational flow assumptions for the aerodynamics. The unique contribution of this work is the introduction of a high-order structural formulation coupled with a high-fidelity method for the aerodynamics. In more details, the Carrera Unified Formulation coupled with the Finite Element Method is implemented to model geometrically complex composite, laminated structures as equivalent bi-dimensional plates. The open-source software SU2 is then used for the solution of the aerodynamic fields. T…

MODELIZACIÓN MEDIANTE CFD DE PARA EVALUAR LA VENTILACIÓN EN UN EDIFICIO ARQUEOLÓGICO, DATOS PRELIMINARES.

2016

[EN] The present study addresses the influences of wind flow structure, as an important factor responsible of material damage (erosion contributing) on “Casa di Diana” Mithraeum, a roman building (130 A.D.) sited on Ostia Antica (archaeological site, Rome – Italy), through the Computational Fluid Dynamics (CFD) simulations and direct measurements for its verification and validation (V&V). In this preliminary work, we present results relating to 3D reconstruction (geometry of the entire building) and the mesh importing on Fluent software. In general, the data check confirms, with ±10%, a good agreement (model) between the numerical solutions and direct measurements data by portable sensor. F…

Influence of drag and turbulence modelling on CFD predictions of solid liquid suspensions in stirred vessels

2014

Abstract Suspensions of solid particles into liquids within industrial stirred tanks are frequently carried out at an impeller speed lower than the minimum required for complete suspension conditions. This choice allows power savings which usually overcome the drawback of a smaller particle-liquid interfacial area. Despite this attractive economical perspective, only limited attention has been paid so far to the modelling of the partial suspension regime. In the present work two different baffled tanks stirred by Rushton turbines were simulated by employing the Eulerian-Eulerian Multi Fluid Model (MFM) along with either the Sliding Grid algorithm (transient simulations) or the Multiple Refe…

A Computational Approach to Conjugate Heat Transfer between Two Fluids in Plate Heat Exchangers of Arbitrary Geometry

2002

Conical Two-Phase Swirl Flow Atomizers—Numerical and Experimental Study

2021

This paper presents the results of numerical simulations for the developed and discussed conical two-phase atomizers with swirl flow, differing in the ratio of the height of the swirl chamber to its diameter. Experiments were carried out for SAN-1 with HS/DS = 1 and SAN-2 with HS/DS = 4 atomizers. The study was conducted over a range of Reynolds number for liquid ReL = (1400

Eulerian two-fluid model of alkaline water electrolysis for hydrogen production

2020

Hydrogen storage is a promising technology for storage of renewable energy resources. Despite its high energy density potential, the development of hydrogen storage has been impeded, mainly due to its significant cost. Although its cost is governed mainly by electrical energy expense, especially for hydrogen produced with alkaline water electrolysis, it is also driven by the value of the cell tension. The most common means of electrolyzer improvement is the use of an electrocatalyst, which reduces the energy required for electrochemical reaction to take place. Another efficient means of electrolyzer improvement is to use the Computational Fluid Dynamics (CFD)-assisted design that allows the…

On the impact of the heat transfer modelling approach on the prediction of EU-DEMO WCLL breeding blanket thermal performances

2020

Abstract The Water-Cooled Lithium-Lead Breeding Blanket is a key component of a fusion power plant, in charge of ensure Tritium production, shield Vacuum Vessel and magnets and remove the heat power deposited by radiation and particles arising from plasma. The last function is fulfilled by First Wall and Breeding Zone independent cooling systems. Several layouts of BZ coolant system have been investigated in the last years to identify a configuration that might guarantee EUROFER temperature below the limit (550 °C) and good thermal-hydraulic performances (i.e. water outlet temperature of 328 °C). A research activity is conducted to study and compare different modelling approaches to simulat…