Search results for "circuit"
showing 10 items of 936 documents
Design of Bilateral Switched Reluctance Linear Generator to Convert Wave Energy: Case Study in Sicily
2013
The aim of this work is a case study of the adaptation bilateral switched reluctance linear generator to the exploitation of energy of the sea. This type of generator can be used to convert wave energy in electrical energy. In this paper we present an analytical sizing and FEM simulation. As for the results, analysis of the data extracted through the simulations it was possible to calculate the emf. The emf was calculated in two cases of motion of the slider: first hypothesis has set the constant speed while the second is a variable speed according to the law of an oscillatory motion of the sea.
New statistical post processing approach for precise fault and defect localization in TRI database acquired on complex VLSI
2013
International audience; Timing issue, missing or extra state transitions or unusual consumption can be detected and localized by Time Resolved Imaging (TRI) database analysis. Although, long test pattern can challenge this process. The number of photons to process rapidly increases and the acquisition time to have a good signal over noise ratio (SNR) can be prohibitive. As a result, the tracking of the defect emission signature inside a huge database can be quite complicated. In this paper, a method based on data mining techniques is suggested to help the TRI end user to have a good idea about where to start a deeper analysis of the integrated circuit, even with such complex databases.
Frequency mapping in dynamic light emission with wavelet transform
2013
International audience; Dynamic photon emission microscopy is an e cient tool to analyse today's integrated circuit. Nevertheless, the reduction of transistor's dimensions leads to more complex acquisitions where many spots can be seen. A frequency characterization of the whole acquired area can help to have a better understanding of it. With that purpose in mind, a new methodology to draw frequency mapping of dynamic light emission acquisition is reported. It is fully automated and based on wavelet transform and autocorrelation function. Regarding the possible use in an industrial context, the suggested method can help to localize abnormal emission activity and it gives some perspectives o…
Arc Fault Detection Method Based on CZT Low-Frequency Harmonic Current Analysis
2017
This paper presents a method for the detection of series arc faults in electrical circuits, which has been developed starting from an experimental characterization of the arc fault phenomenon and an arcing current study in several test conditions. Starting from this, the authors have found that is it possible to suitably detect arc faults by means of a high-resolution low-frequency harmonic analysis of current signal, based on chirp zeta transform, and a proper set of indicators. The proposed method effectiveness is shown by means of experimental tests, which were carried in both arcing and nonarcing conditions and in the presence of different loads, chosen according to the UL 1699 standard…
Sub-mA current measurement by means of GMR sensors and state of the art lock-in amplifiers
2015
Electric current measurement at the range of μA in integrated circuit has been traditionally carried out by micro-electronically engineered systems, such as current mirrors or charging capacitors. However, off-line, i.e., non-intrusive methods provide advantages related to size and power consumption. In this sense, giant magnetoresistance (GMR) magnetic sensors are optimal due to their sensitivity and CMOS compatibility. In this work, we make use of specifically designed CMOS GMR-based current sensors in combination with a custom electronic interface based on a low-voltage low-power lock-in amplifier, demonstrating the capability of this combination for current measurement in the range of μ…
A low-cost compact uniplanar Quasi–Yagi printed antenna
2008
A low cost directive uniplanar broadband printed Quasi–Yagi antenna design is presented. As a particular realization, some prototypes have been designed to operate in the 2.45 GHz band. They have been then modeled, fabricated onto standard printed circuit dielectric substrate and tested successfully. For the design and the modeling processes, we have make use of FDTD based in-house developed algorithms. The obtained bandwidth is, for all the considered cases, better than 15%. The main radiation characteristics are 2–5.5 dBi gain, depending on the number of director elements, and better than 25 dB front-to-back ratio. Overall antenna size was, in any case lesser than 1 λ × 0.5 λ. © 2008 Wile…
Design of Yagi-like printed antennas for WLAN applications
2007
A directive broadband printed Yagi-like antenna design is presented. We have focused on the 2.45 GHz WLAN band, at which some designs have been carried out. For the design and the modelling processes, we made use of FDTD based in-house developed algorithms. Some selected prototypes have then been fabricated onto a low-cost printed circuit board dielectric substrate and tested successfully. Bandwidths higher than 10% and moderate to high (>7 dBi) gains can be obtained this way. © 2007 Wiley Periodicals, Inc. Microwave Opt Technol Lett 49: 2174–2178, 2007; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.22655
Charge measurement using an array of Faraday’s Cups on a printed circuit board
2014
Abstract An absolute method of measuring charge is to use a Faraday Cup (FC) principle. This study relates to a novel method of measuring charge on a flat substrate, which is coated with charged powder particles. The substrate consists of an array of FC with different dimensions. The sensor is manufactured using flame-retardant printed circuit board (PCB) technology. The objective of this work is to reduce the charge sharing by developing a grounded shield cup around each conductive cup in the array and accordingly increase cup-to-ground capacitance. The results have confirmed that the improved well shielding would provide a more accurate quantitative charge measurement.
Noise and gain performance of PSA transistor series for personal communication systems vs. emitter number and operating conditions
1995
The booming market of communication system applications in the low microwave range put greater demands on the component performance at lower supply voltages and limited current consumption, as well as on production cost and integration level. In this work, we present the results of an extensive characterization activity carried out on several advanced polysilicon bipolar transistors as requested by the manufacturer. The devices were grouped according to their emitter finger number and were characterized over the 2-6 GHz frequency range in terms of noise, gain and scatterino parameters at different bias conditions. A comparative analysis has been performed to explore how the transistor perfo…
Development of 3D Anti-Swing Control for Hydraulic Knuckle Boom Crane
2021
In this paper, 3D anti-swing control for a hydraulic loader crane is presented. The difference between hydraulic and electric cranes are discussed to show the challenges associated with hydraulic actuation. The hanging load dynamics and relevant kinematics of the crane are derived to model the system and create the 3D anti-swing controller. The anti-swing controller generates a set of tool point velocities which are added to the electro-hydraulic motion controller via feedforward. A dynamic simulation model of the crane is made, and the control system is evaluated in simulations with a path controller in actuator space. Simulation results show significant reduction in the load swing angles …