Search results for "composite"

MECHANICAL, RHEOLOGICAL AND THERMAL EVALUATION OF POLY(LACTIC ACID) (PLA)/MICRO FIBRILLATED CELLULOSE (MFC) PLASTICIZED BIOCOMPOSITES PRODUCED WITH F…

2022

The use of Micro Fibrillated Cellulose (MFC) as filler for polymeric matrices attempts an increasing interest both in academia and industry. In this framework, encouraging results have been obtained using plasticizers, as dispersing aids, during twin-screw extrusion that optimizes the process parameters and avoid MFC agglomeration. In this work, two commercial typologies of waterborne solution of MFC (Exilva and Celish) were melt-compounded in a PLA matrix through semi-industrial twin-screw extruder and calendered, producing films of 150 μm thickness. These films were mechanically and thermally characterized, moreover the migration of the plasticizer along the time was evaluated through ana…

Green Composites Based on Hedysarum coronarium with Outstanding FDM Printability and Mechanical Performance

2022

The addition of natural scraps to biodegradable polymers has gained particular interest in recent years, allowing reducing environmental pollution related to traditional plastic. In this work, new composites were fabricated by adding 10% or 20% of Hedysarum coronarium (HC) flour to Poly (lactic acid) (PLA). The two formulations were first produced by twin screw extrusion and the obtained filaments were then employed for the fabrication of composites, either for compression molding (CM) or by fused deposition modeling (FDM), and characterized from a morphological and mechanical point of view. Through FDM it was possible to achieve dense structures with good wettability of the filler that, on…

Strength of cellulosic fiber/starch acetate composites with variable fiber and plasticizer content

2014

In this experimental study, the performance of injection-molded short flax and hemp fibers in plasticized starch acetate were analyzed in terms of strength. Parameters involved in the analysis are a variable fiber and plasticizer content. The measured strength of the composites varies in the range of 12–51 MPa for flax fibers and 11–42 MPa for hemp fibers, which is significantly higher than the properties of the unreinforced starch acetate matrix. The micro-structural parameters used in modeling of composite strength were obtained from optical observations and indirect measurements. Some of these parameters were qualitatively verified by X-ray microtomography.

Biochar Particles Obtained from Agricultural Carob Waste as a Suitable Filler for Sustainable Biocomposite Formulations

2022

In the context of sustainable and circular economy, the recovery of biowaste for sustainable biocomposites formulation is a challenging issue. The aim of this work is to give a new life to agricultural carob waste after glucose extraction carried out by a local factory for carob candy production. A pyrolysis process was carried out on bio-waste to produce biofuel and, later, the solid residual fraction of pyrolysis process was used as interesting filler for biocomposites production. In this work, biochar particles (BC) as a pyrolysis product, after fuels recovery of organic biowaste, specifically, pyrolyzed carobs after glucose extraction, were added on poly(butylene-adipate-co-terephthalat…

Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling

2022

In this work, an innovative green composite was produced by adding Hedysarum coronarium (HC) flour to a starch-based biodegradable polymer (Mater-Bi®, MB). The flour was obtained by grinding together stems, leaves and flowers and subsequently sieving it, selecting a fraction from 75 μm to 300 μm. Four formulations have been produced by compression molding (CM) and fused deposition modeling (FDM) by adding 5%, 10%, 15% and 20% of HC to MB. The influence of filler content on the processability was tested, and rheological, morphological and mechanical properties of composites were also assessed. Through CM, it was possible to obtain easily homogeneous samples with all filler amounts.…

Exploiting the Redox Activity of MIL-100(Fe) Carrier Enables Prolonged Carvacrol Antimicrobial Activity

2022

The design of efficient food contact materials that maintain optimal levels of food safety is of paramount relevance to reduce the increasing number of foodborne illnesses. In this work, we develop a smart composite metal-organic framework (MOF)-based material that fosters a unique prolonged antibacterial activity. The composite is obtained by entrapping a natural food preserving molecule, carvacrol, into a mesoporous MIL-100(Fe) material following a direct and biocompatible impregnation method, and obtaining particularly high payloads. By exploiting the intrinsic redox nature of the MIL-100(Fe) material, it is possible to achieve a prolonged activity against Escherichia coli and Listeria i…

Conifer needles as thermoplastic composite fillers: structure and properties

2016

This study describes the properties of thermoplastic polymer composites based on polyethylene (of low and high density) and ethylene-propylene copolymers using various types of conifer needles (pine, spruce, fir, and cedar) as fillers. For the needles, thermogravimetric analysis (TGA) and TGA/Fourier transform infrared spectroscopy (TGA/FTIR) were performed to investigate their structures and thermal resistance, as required for the composite processing methods. Moreover, structural differences were studied for the analyzed fillers and composite materials (FTIR). The results were compared with the values obtained for composites with conifer wood flour. Composites with conifer needles (pine) …

Creep Behavior of Poly(lactic acid) Based Biocomposites

2017

Polymer composites containing natural fibers are receiving growing attention as possible alternatives for composites containing synthetic fibers. The use of biodegradable matrices obtained from renewable sources in replacement for synthetic ones is also increasing. However, only limited information is available about the creep behavior of the obtained composites. In this work, the tensile creep behavior of PLA based composites, containing flax and jute twill weave woven fabrics, produced through compression molding, was investigated. Tensile creep tests were performed at different temperatures (i.e., 40 and 60 °C). The results showed that the creep behavior of the composites is strongly inf…

MECHANICAL PROPERTIES AND BIODEGRADABILITY OF MATER-BI®/WOOD FLOUR ECOCOMPOSITES

2010

Characterization of Self-Growing Biomaterials Made of Fungal Mycelium and Various Lignocellulose-Containing Ingredients

2022

In this study, novel blends of mycelium biocomposites (MB) were developed. Various combinations of birch sawdust and hemp shives with birch bark (BB) and wheat bran (WB) additives were inoculated with basidiomycete Trametes versicolor to produce self-growing biomaterials. MB were characterized according to mycelial biomass increment in final samples, changes in chemical composition, elemental (C, H, N) analyses, granulometry of substrates, water-related and mechanical properties, as well as mold resistance and biodegradability. The mycelial biomass in manufactured MB increased by ~100% and ~50% in hemp and sawdust substrates, respectively. The lignocellulose ingredients during fungal growth…