Search results for "composites"
showing 10 items of 1905 documents
Improvement of the photo-stability of nanocomposite based LDPE/EVA films
2008
Influence of the matrix on photo-oxidative degradation of polyolefin based nanocomposite films
2008
Mechanical response of PLA-based biocomposites under creep conditions
2017
Over the last decades, polymer composites containing natural fibers are receiving growing attention both from academia and the industry, as possible alternatives of composites containing synthetic fibers [1]. Moreover, in order to reduce the environmental impacts related to the use of oil-derived polymer matrices, biodegradable ones obtained from renewable sources such as poly(lactic acid) (PLA) have been considered [2]. Several papers are available regarding the mechanical behavior of natural fibers reinforced PLA composites, but only few deal with their creep behavior [3]. In the present work, the tensile creep behaviour of PLA based composites, containing flax and jute plain weave woven …
Nanofilled Thermoplastic-Thermoplastic Polymer Blends
2014
Modelling the structure-property relationships of high performance PBAT-based biocomposites with natural fibers obtained from Chamaerops humilis dwar…
2022
Two fibrous fillers were achieved from stalks and leaves of Chamaerops humilis dwarf palm and tested as reinforcing agents for poly(butylene adipate co-terephthalate) (PBAT)-based composites. The influence of filler type and content on the morphomechanical properties of the green composites was assessed. The outcomes of tensile tests pointed out that both fillers are strong candidates to overcome the two main limiting aspects of PBAT, that is, the lack of both stiffness and cost-effectiveness, while preserving its stretchability and environmental sustainability. The remarkable stiffness increments (up to 300%), combined with fair retention of stretchability (33%) and doubled resistance, led…
Green composites for fertilizer controlled release produced by compression molding and FDM
2023
Excessive fertilization causes ecological problems due to leaching issues. To solve this problem and promote agriculture sustainability an innovative green composite for controlled release fertilizers was produced by adding NPK fertilizer flour to a biodegradable polymer with or without Opuntia Ficus Indica (OFI) particles. Six formulations were produced and employed for the fabrication of devices both for compression molding (CM) and fused deposition modeling (FDM). Both fillers displayed a good dispersion in the composites, excellent adhesion with the polymeric matrix and effectively acted as reinforcement. The decrease of NPK release rate (up to 30 days) was achieved using whole composit…
Physical and antibacterial properties of PLA electrospun mats loaded with carvacrol and nisin
2022
Functional, biopolymeric electrospun structures for the controlled release of antimicrobial agents are gaining in-creasing interest in food packaging applications. In this study, the physical and antibacterial performances of ternary systems composed of polylactic acid (PLA) electrospun mats loaded with 20 wt% of different relative amounts of carvacrol (CRV) and a commercial nisin formulation (Nis) were assessed. Scanning electron micrographs displayed micro-scaled fibers with different diameter size distributions depending on the relative concentrations of the additives. The PLA/CRV/Nis membranes??? wettability was affected by the relative amount of CRV and Nis loaded, switching from hydro…
The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.
2022
Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could …
Recent Developments and Formulations for Hydrophobic Modification of Carrageenan Bionanocomposites
2023
Versatility of the anionic algal polysaccharide carrageenan has long been discussed and explored, especially for their affinity towards water molecules. While this feature is advantageous in certain applications such as water remediation, wound healing, etc., the usefulness of this biopolymer is extremely limited when it comes to applications such as food packaging. Scientists around the globe are carrying out research works on venturing diverse methods to integrate hydrophobic nature into these polysaccharides without compromising their other functionalities. Considering these foregoing studies, this review is designed to have an in-depth understanding of diverse methods and techniques ado…
The assessment over time of the performance of jute-basalt hybrid composites for cladding panels
2017
The technology of dry assembly to produce multi-layer panels is an efficient alternative to traditional systems. Eco-sustainable systems are increasingly studied, particularly fiber reinforced composites for external cladding, based on natural fibers. Nevertheless, durability data on these composites are still lacking, being this is a really actual theme, especially for their potential use in outdoor applications. In this way, hybridization of natural fibers with mineral fibers as basalt ones appears promising. In the present paper, the performance of jute-reinforced laminate was compared with those of two jute/basalt reinforced hybrid laminates. The laminates were manufactured by means of …