Search results for "crystallinity"
showing 10 items of 248 documents
Small angle scattering study of the structure of isotactic polypropylene-hydrogenated oligo(cyclopentadiene) blends
1996
Abstract Blends of isotactic polypropylene ( i PP) and hydrogenated oligo cyclopentadiene (HOCP) have been studied by means of small angle X-ray scattering in the temperature range 70–160°C. The structure of blends containing less than 25% HOCP is very similar to the one of plain i PP, i.e. lamellae whose thickness increases by increasing the temperature. Blends containing more than 25% HOCP are characterized by two kinds of lamellae formed by layers of i PP and amorphous material rich in i PP and in HOCP, respectively. The crystallizable i PP present in both phases crystallizes from the melt, in analogy to what happens in HDPE/HOCP blends and in agreement with the values of the crystallini…
Sustainable nanocomposites based on halloysite nanotubes and pectin/polyethylene glycol blend
2013
Abstract This study was focused on the preparation and characterization of biofilms based on pectin/polyethylene glycol 20000 (PEG) blend and halloysite nanotubes (HNTs). The obtained blends loaded with a natural nanoclay are proposed as sustainable alternative to the polymers produced from non-renewable resources such as fossil fuels. Properties of technological interest have been monitored and they were correlated to the structural features of the nanocomposites. It turned out that the wettability of the films can be tuned by changing the composition and the distribution of HNTs into the material as well as the surface roughness. The tensile properties of the blend are enhanced by the pre…
Studies on electron-beam irradiation and plastic deformation of medical-grade ultra-high molecular weight polyethylene
2011
Abstract Separated and combined electron-beam irradiation and plastic deformation effects on the structures of ultra-high molecular weight polyethylene (UHMWPE) were studied. It was found that the concentration of carbonyl (ketones, esters and peresters), hydroxyl and vinyl groups increases with the growing dose of adsorbed electrons. It also tends to exhibit a slight increase in the melting point and crystallinity of the samples. A mechanical stress in the polymer was found to accelerate radiation-induced degradation. It was concluded that each of the factors studied (i.e. electron beam sterilization and plastic deformation) had a different impact on the polymer structure. The change in th…
Influence of“controlled processing conditions” on the solidification of iPP, PET and PA6
2002
In this work reliable experimental data for three semicrystalline polymers (iPP, PA6, PET) crystallised under pressure and high cooling rates are supplied. These results were achieved on the basis of a model experiment where drastic controlled solidification conditions are applied. The final objective was to quantify the effect of two typical operating conditions (pressure and cooling rate) on the final properties and morphology of the obtained product. The influence of processing conditions on some macroscopically relevant properties, such as density and micro hardness is stressed, together with the influence of processing conditions on the product morphology, investigated by means of Wide…
The use of the indentation test for studying the solidification behaviour of different semicrystalline polymers during injection moulding
2005
Summary: An in-line method for monitoring the solid-ificationprocess during injection molding of semicrystallinepolymers (demonstrated previously in J. Appl. Polym. Sci.2003, 89, 3713) is based on a simple device, where anadditional ejector pin is pushed on the injection molded partatdifferenttimesduringthesolidificationphase.The‘inden-tation depth profile’, i.e., residual deformation as a functionoftime,wasobtainedandallowedtodeterminetheevolutionof the solidification front in the mold as a function of thecooling time. The present work shows the reliability andthe powerfulness of the aforementioned method for a largevariety of different semicrystalline polymers (PET, PBT,polyamide-6 PA6, isota…
Viscoelastic recovery behavior following Atomic Force Microscope nanoindentation of semi-crystalline poly(ethylene)
2007
The residual imprint left behind by the AFM nanoindentation of polymers has been seldom studied in the past. In this work, the evolution of indentations at room temperature performed on a semicrystalline poly- (ethylene) in a broad range of experimental conditions is presented. The study shows that the recovery after 24 h is substantial, although not complete. Moreover, the dynamics of the recovery process is not seen to depend on the magnitude of the applied load for the nanoindentation, but instead on the rate of the indentation used. This points out that viscoelastic processes are minimized when performing fast nanoindentations, while at low loading rates there seems to be a residual vis…
The use of master curves to describe the simultaneous effect of cooling rate and pressure on polymer crystallization
2003
In a previous work a master-curve approach was applied to experimental density data to explain isotactic polypropylene (iPP) behaviour under pressure and high cooling rates. Suitable samples were prepared by solidification from the melt under various cooling rate and pressure conditions with the help of a special apparatus based on a modified injection moulding machine. The approach here reported is more general than the case study previously shown, and is suitable to be applied to several materials and for different measures related to crystalline content. The proposed simple model is able to predict successfully the final polymer properties (density, micro-hardness, crystallinity) by supe…
Improvement of biphasic polymerization by application of binary ionic liquid mixture
2013
Abstract The mixture of two ionic liquids, 1- n -butyl-3-methylimidazolium and 1-(2-phenylethyl)-3-methylimidazolium chloroaluminates, [C 4 -mim][AlCl 4 ] and [PhC 2 -mim][AlCl 4 ], were applied as a medium to immobilize the Cp 2 TiCl 2 titanocene catalyst for biphasic ionic liquid/hexane ethylene polymerization. The system makes possible to perform the reaction at lower temperatures, below the melting temperature of the aralkyl ionic liquid. A better separation of the ionic liquid phase was observed and an easier mass transfer of the polymer product from the ionic liquid to the hexane phase was obtained. The polyethylene reveals bimodal distribution of molecular weight. It is characterized…
Synthesis and properties of polymers with unusual structure
1985
This lecture summarize some recent results of our current research. The first part describes the homopolymerization and copolymerization of a monocyclic and two bicyclic unsaturated acetals. In this way polyacetals with 1,4-cis-butadiene units and cyclohexene units respectively are obtained. Secondly, the N-substitution of polyamides is described. By N-metalation and subsequent alkylation comb-like polyamides are available. Longer branches cause a side-chain crystallinity. The anionic “grafting-from” technique forms irregular branched polyamides. By termination reaction between living ends of poly(2-isopropenylnaphthalene) and suitable electrophiles new macromonomers are available. The last…
Copolymers with ordered chemical structure
1984
Copolymers with well defined sequences can be obtained for instance by ring-opening polymerization of selected acetals. In this way regular copolymers of formaldehyde and ethylenoxide of the following structure are available2. In the same way some other copolymers with formaldehyde units were obtained. Of special interest are unsaturated polyacetales; for instance3 They can be modified by chemical reactions, for instance by hydrogenation, addition of bromine, iodine isocyanate or epoxidation. Recently a bicyclic unsaturated cycloacetal was prepared and polymerized4 Branched copolymers with a definite number of uniform sidechains are prepared by N-alkylation of polyamides5 The dependence of …