Search results for "dab"

Housing affordability nelle regioni urbane. Una proposta metodologica per definire il reddito soglia

2018

Within context of urban disintegration and social fragmentation, the concept of post-metropolis induces to critically consider the typical dichotomy between centre and periphery. Even in marginal areas where metropolis did not develop according to traditional stages and classical models, the traditional analytical categories are no longer able to interpret the widespread phenomenon of regional urbanization. In any case, the large urban regions are recognized by some authors not only as driving-force of the global economy, but also as the main sources of inequality and of social/environmental injustice; places where the gap between high and low income of social groups has been exacerbated. I…

A grid of material and immaterial laboratories for supporting the sustainability of transportation: the RESET project in Sicily

2015

Transportation is a crucial sector, to be suitably approached in order of getting human activities in more environmentally sustainable paths. In fact, in developing, as well in less developing, countries people and freights mobility are responsible of important amount of pollutant emissions and are cause of significant levels of energy consumptions. In this paper, a Sicilian regional project is presented, aiming at establishing an interconnected grid of material and immaterial laboratories. These laboratories, that are devoted at inducing more virtuous behaviors in the transportation policies, are constituted by equipment and software tools, mainly located in the region’s universities, acti…

Physical and antibacterial properties of PLA electrospun mats loaded with carvacrol and nisin

2022

Functional, biopolymeric electrospun structures for the controlled release of antimicrobial agents are gaining in-creasing interest in food packaging applications. In this study, the physical and antibacterial performances of ternary systems composed of polylactic acid (PLA) electrospun mats loaded with 20 wt% of different relative amounts of carvacrol (CRV) and a commercial nisin formulation (Nis) were assessed. Scanning electron micrographs displayed micro-scaled fibers with different diameter size distributions depending on the relative concentrations of the additives. The PLA/CRV/Nis membranes??? wettability was affected by the relative amount of CRV and Nis loaded, switching from hydro…

The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.

2022

Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could …

Polymer-based 'green' composites

2009

Biodegradable polymer-wood flour composites: main properties and biodegradability

2009

During the last years, a considerably increasing rate of attention has arisen on biodegradable polymers. In the meanwhile, the use of wood-plastic composites (WPC) has grown in importance, especially in the United States. The combination of biodegradable polymers and wood-based fillers allows obtaining the typical advantages achievable with the use of WPCs, with the further advantage of the biodegradability and compostability of the matrix (and not only of the filler). In this work, the characterization and the biodegradability assessment of Mater-Bi®-wood flour composites have been carried out.

Polylactide biodegradable scaffolds for tissue engineering applications phase separation-based techniques

2011

One of the most reliable techniques for the preparation of biodegradable scaffoldssuitable for tissue engineering applications (e.g. regeneration of wounded/damagedtissues) is based on liquid/liquid phase separation of ternary solvent/antisolvent/polymersolutions. In particular, two phase separation protocols are examined here: ThermallyInduced Phase Separation (TIPS) and Diffusion Induces Phase Separation (DIPS). According to the former protocol, a thermodynamically stable polymeric ternarysolution is brought below its metastability/instability point (spinodal/binodal curve) byquench in a cooling medium: under opportune conditions, a foam-like structure is formedby nucleation and 3-D growt…

Patent number RM2009A000073: Procedimento di preparazione di scaffold polimerici preangiogenizzati

2009

Classe proposta A61F - Filtri da inserire nei vasi sanguigni; protesi; apparecchi ortopedici e curativi per contraccezione; fomentazione; trattamento o protezione degli occhi e delle orecchie; bendaggi, garze per medicazioni e assorbenti; necessario per il pronto soccorso

Poly lactic acid based scaffolds for vascular tissue engineering

2012

A critical obstacle encountered by tissue engineering is the inability to maintain large masses of living cells upon transfer from the in vitro culture conditions to host in vivo. Capillaries, and the vascular system, are required to supply essential nutrients, including oxygen, remove waste products and provide a biochemical communication "highway". The successful use of tissue-engineered constructs is currently limited to thin or avascular tissues, such as skin or cartilage, for which post-implantation neovascularisation from the host is sufficient to meet the demand for oxygen and nutrients. To succeed in the application of tissue engineering for bigger tissues, such as bone or muscle, t…

Fluid-structure interaction and flow redistribution in membrane-bounded channels

2019

The hydrodynamics of electrodialysis and reverse electrodialysis is commonly studied by neglecting membrane deformation caused by transmembrane pressure (TMP). However, large frictional pressure drops and differences in fluid velocity or physical properties in adjacent channels may lead to significant TMP values. In previous works, we conducted one-way coupled structural-CFD simulations at the scale of one periodic unit of a profiled membrane/channel assembly and computed its deformation and frictional characteristics as functions of TMP. In this work, a novel fluid&ndash