Search results for "density polyethylene"
showing 10 items of 140 documents
Effect of irradiation temperature and dose rate on the mechanical tensile behaviour of low density polyethylene
1993
Abstract The effect of ageing due to gamma radiation, at various dose rates and temperatures, on the mechanical tensile behaviour of low density polyethylene is studied. In order to detect synergistic effects, tensile tests on samples subjected to thermal treatment corresponding to the same temperature for the same time as for the irradiation tests have also been performed. The results indicate a generalized decrease of the elongation at break, with brittleness of the material for the most severe ageing treatments. For modulus values, an increase is observed for particular experimental conditions. These results are related to morphological and structural modifications induced in the polymer…
Improvement of the mechanical properties of photo-oxidized films after recycling
2002
Mechanical recycling of post-consumer plastics gives rise, in most cases, to secondary materials with mechanical properties worse than those of the reclaimed polymer. This is mostly due to the thermomechanical treatment undergone during the melt reprocessing operations. In this work, low density polyethylene films have been photo-oxidized in artificial accelerated ageing conditions and then the brittle films have been melt reprocessed. It is shown that the secondary material, after reprocessing, shows mechanical properties, in particular elongation at break, better than those of the photo-oxidized films. This behaviour has been attributed to the fact that the melt reprocessing has the effec…
Durability of a strach-based biodegradable polymer
2007
Abstract The photo-oxidation and the photo-stabilization of a commercial biodegradable polymer have been investigated in order to establish the possibility of using this polymer as raw material for films for agriculture. The degradation has been followed by measuring the mechanical properties as a function of photo-oxidation time and in particular by following the elongation at break. The virgin polymer, made from maize starch and a synthetic biodegradable polyester, shows poor resistance to the UV irradiation as observed by the fast decay of the elongation at break, but the presence of small amounts of conventional UV stabilizers strongly improves the durability of this polymer. The UV sta…
Prediction of the flow curves of thermoplastic polymer/clay systems from torque data
2014
Abstract The aim of this work was to determine some relevant rheological parameters of polymer/clay systems using mixing torque and mixing speed data obtained during processing in an internal mixer. The method used was originally proposed by Marquez et al. for monophase polymers, and is here applied to polymer/clay systems for the first time. Several clay-containing composites based on different polymer matrices (i.e., LDPE, HDPE, PA6, EVA) were used to verify the effectiveness of the method for measuring the flow curves of these polymer/clay systems. The results indicated that, for all the systems at low clay level, the rheological curves calculated with the Marquez method fit quite well t…
Polymer mechanical recycling: downcycling or upcycling?
2004
Recycled plastics are considered as materials with physical, mechanical and aesthetic properties worse than the virgin ones. In fact, this is true because degradation during lifetime and during the recycling operations changes the structure and the morphology of the polymers and then the final properties of the secondary material. Several “strategies” are under investigation, and in some cases also applied, in order to avoid further degradation during recycling and, if possible, to repair the macromolecules broken during lifetime and then to restore or to improve the initial properties. In this paper the more important techniques, already used in industry or under investigation, according …
Interactions between aroma and edible films. 1. Permeability Of methylcellulose and low-density polyethylene films to methyl ketones.
1998
This work contributes to the study of aroma transfers through edible and plastic packaging films. Permeability, sorption, and diffusivity of three methyl ketones (2-heptanone, 2-octanone, and 2-nonanone) in and through low-density polyethylene and methylcellulose-based edible films have been determined. Permeability was measured using a dynamic method coupled with a gas chromatograph. The methyl ketone permeability of polyethylene films mainly depends on diffusivity of the penetrant in the polymer. In the case of 2-heptanone, a saturation of the polymer network is observed at high vapor concentrations. The formation of clusters could take place when concentrations are higher in the vapor ph…
On the Improvement of the Processability of UHMW-HDPE by Adding a Liquid Crystalline Polymer and a Fluoroelastomer
2001
Ultra-high molecular weight polyethylene possesses many interesting properties but a very bad processability. This material is not usually processed in conventional devices but only by compression moulding and RAM extrusion. Low molecular weight polyethylene can be used to improve the processability. In this work small amounts of a fluoroelastomer and of a liquid crystalline polymer have been used as processing aids to improve the extrudability of this polymer. In fact, the die pressure decreases whereas the output flow rate slightly increases with increasing concentration of the processing aids. Solution viscosity data shows that reduction of the mechanical stress during extrusion decrease…
Melt Strength and Extensibility of High-Density Polyethylene
1984
The extensional flow of polymer melts has been extensively studied because of its importance in many technological processing operations and, from a more fundamental point of view, because the tensile properties of the polymer melts cannot be correlated directly with shear viscosity behavior.1–5
Crystallization kinetics of LDPE/Ny6 blends
1988
The crystallization behaviour of low density polyethylene/nylon 6 blends has been investigated as a function of the composition. The melting points of the polymers are almost uninfluenced by the presence of the other homopolymers except for blends with a nylon content of 75–90%. Blends with 10% nylon content do not exhibit the crystallization peak during the cooling step probably because of the low concentration and high viscosity of the low density polyethylene matrix. The crystallinity degree of the polyethylene is independent of the composition, while some variations are shown by the polyamide. Finally the rate of nucleation is strongly affected by the composition, in particular for the …
Morphology and Rheology of HDPE/LCP Blends Compatibilized by a Novel PE-g-LCP Copolymer
1999
A novel graft copolymer (PE-g-LCP) consisting of polyethylene (PE) backbones and liquid crystalline polymer (LCP) branches was synthesized via reactive blending of an acrylic acid-functionalized PE (Escor 5000 by Exxon) with a semiflexible LCP (SBH 1 : 1 : 2 by Eniricerche S.p.A.). The crude reactive blending product (COP) was shown by investigation of the fractions soluble in boiling toluene and xylene and of the residue to contain unreacted Escor and SBH, together with the graft copolymer forming the interphase. The compatibilizing activity of COP for PE/SBH blends, compared to that of pure Escor, was investigated using two PE grades. The COP addition into 80/20 PE/SBH blends caused a muc…