Search results for "electrical"
showing 10 items of 11048 documents
Improving the high temperature oxidation resistance of Ti-β21S by mechanical surface treatment
2020
The improvement of the high temperature oxidation resistance of titanium alloys is currently a technological challenge. Mechanical surface treatments as shot-peening (SP) have shown their ability to improve the behaviour of pure zirconium and titanium. However, shot-peening treatments can induce a significant surface contamination. Laser shock peening (LSP) appears as a good alternative. Here, we have investigated the effect of SP and LSP treatments on the HT oxidation behavior of Ti-β21S. Samples treated by these methods have been compared to untreated ones for long exposures (3000 h) at 700 °C in dry air. The samples placed in a furnace at 700 °C were periodically extracted to be weighed.…
Metrological Properties of the Test Setup for Determination Shielding Effectiveness of the Industrial Cable Connectors
2017
Abstract The paper presents results related to assessment of the repeatability and reproducibility of the measurement test setup for determination the relative value of the shielding effectiveness coefficient of the industrial connectors. The construction of the proposed test setup, the measurement method and the procedure for the analysis of measurement results were described. To determine the value of the repeatability and reproducibility coefficient, the two–way analysis of variance was used, which additionally allows for an assessment of the influence of individual sources of variance. The measurements and their analysis were conducted for several frequencies in the range up to 1 GHz. A…
Controlled thermal oxidation of nanostructured vanadium thin films
2016
Abstract Pure V thin films were dc sputtered with different pressures (0.4 and 0.6 Pa) and particle incident angles α of 0°, 20° and 85°, by using the GLancing Angle Deposition (GLAD) technique. The sputtered films were characterized regarding their electrical resistivity behaviour in atmospheric pressure and in-vacuum conditions as a function of temperature (40–550 °C), in order to control the oxidation process. Aiming at comprehending the oxidation behaviour of the samples, extensive morphological and structural studies were performed on the as-deposited and annealed samples. Main results show that, in opposition to annealing in air, the columnar nanostructures are preserved in vacuum con…
Contrasting topologies for regular interconnection networks under the constraints of nanoscale silicon technology
2010
Nowadays, system designers have adopted Networks-on-Chip as communication infrastructure of general-purpose tile-based Multi-Processor System-on-Chip (MPSoC). Such decision implies that a certain topology has to be selected to efficiently interconnect many cores on the chip. To ease such a choice, the networking literature offers a plethora of works about topology analysis and characterization for the off-chip domain. However, theoretical parameters and many intuitive assumptions of such off-chip networks do not necessarily hold when a topology is laid out on a 2D silicon surface. This is due to the distinctive features of silicon technology design pitfalls. This work is a first milestone t…
The Effect of the Harmonic Content Generated by AC/DC Modular Multilevel Converters on HVDC Cable Systems
2019
With the increasing penetration of renewable and decentralized energy sources into the power grid, an extended use of DC voltages is expected on both distribution and transmission levels. Generation of DC voltages by means of voltage source converters is associated with a wide spectrum of harmonic distortions at converter terminals, both on the ac and on the dc sides. This can lead to partial discharges in power cables, which deteriorate insulation material thus weakening its performance and reducing cable life-time. In the previously published paper, the effect of harmonic distortion on appearance of partial discharges in cable insulation was evaluated. Here, the study related to the PD be…
FOC with Resolver Implementation for PMSM Drives by Using a Low Cost Atmel SAM3X8E Microcontroller
2020
The aim of this paper is the low-cost experimental implementation of a field oriented control strategy for a Permanent Magnet Synchronous Motor (PMSM) by using an Atmel SAM3X8E microcontroller, mounted on an Arduino DUE board. In this electrical drive for PMSM, a resolver is used in order to measure the rotor position and speed: Therefore, the low-cost Arduino DUE performs not only FOC algorithm and phase currents data acquisition, but also a resolver-To-digital converter process, rotor position and speed data acquisition, and resolver signals management. The code has been implemented in the open source Arduino IDE, using C language, whereas the control and plot visualization interfaces hav…
A new technique for partial discharges measurement under DC periodic stress
2017
The aim of the present work is to recognize the type of defect in insulating materials employed in DC electrical systems. This analysis, under AC stress, is carried out by using the Phase Resolved method (PRPD). While, under constant voltage stress this method cannot be performed and measurements show complexities. In order to overcome these problems, a new technique is proposed, based on the application of a periodic continuous waveform. Simulation results, carried out by using a model based on a time-variable conductance of an air void defect, showed the PRPD pattern that can be obtain. Furthermore, compared to the constant DC stress, the measurement duration became lower and the discharg…
Acoustic Wave Behavior in a Specimen Containing an Air Void Defect
2019
The PEA method is the most used technique for the space charge measurements. As is well known, this method uses pressure waves to detect the charges accumulated in solid dielectrics. Based on its working principle, the generated acoustic waves travel within PEA cell and the specimen under test in order to be finally detected by the piezoelectric sensor. For a multilayer specimen and, in particular, in case of different materials that make up the specimen, the acoustic wave reflection is inevitable. Considering that, in several cases, the reflected waves could be detected by the piezoelectric sensor before than the main signals, the PEA cell output profile could results distorted. Based on t…
Long term stability testing of oxide unicouple thermoelectric modules
2019
Thermoelectric devices based on oxides are good candidates for energy harvesting technologies for use in aggressive conditions where the materials should withstand high temperatures and corrosive environments over prolonged time. This leads to a natural concern for the stability of the electrical contacts, especially on the hot side of the module. In this work, we have assembled several prototype unicouple thermoelectric modules made by pyrolyzed and spark plasma sintered n-type CaMnO3 and p-type Ca3Co4O9 and then tested under different conditions mimicking end-user applications. For baseline experiments we have chosen to use nickel as the contact material in order to show the effect of its…
Simulation of IQE tuning of individual cells for DC-balancing multijunction tandem cells
2016
In the present work, the performance of stacks of cells connected in series is examined at different levels of internal quantum efficiency (IQE). Incident photons, generated by employing the ASTM G173-03 data set, are accounted for individually as they interact with the stack of cells. The efficiencies of the devices studied are dependent upon the DC balance throughout the stack of cells. It is demonstrated that reducing the internal quantum efficiency of upper cells can lead to a better DC balance and thereby higher efficiency.