Search results for "electrolyte"
showing 10 items of 746 documents
Behavior of alloying elements during anodizing of Mg-Cu and Mg-W alloys in a fluoride/glycerol electrolyte
2015
Anodizing of sputtering-deposited magnesium and Mg-0.75at.%Cu and Mg-1.23at.%W alloys has been carried out in a fluoride/ glycerol electrolyte. The aims of the study were to investigate the enrichment of alloying elements in the alloy immediately beneath the anodic film and the migration of alloying element species in the film. The specimens were examined by electron microscopy and ion beam analysis. An enrichment of copper is revealed in the Mg-Cu alloy that increases with the anodizing time up to ∼6×1015 Cu atoms cm-2. Copper species are then incorporated into the anodic film and migrate outwards. In contrast, no enrichment of tungsten occurs in the Mg-W alloy, and tungsten species are im…
Characterization and properties of PEO coatings on 7075 Al alloy grown in alkaline silicate electrolyte containing KMnO 4 additive
2017
Abstract Plasma electrolytic oxidation (PEO) was used to modify the surface of 7075 Al alloy by applying a bipolar pulsed-current in a silicate based electrolyte containing 0 to 3 g L− 1 KMnO4. For the coating produced in the base electrolyte, crystalline γ-Al2O3 was the main phase, while the coatings formed at the presence of KMnO4 consisted of α-Mn2O3 containing Si and Al oxides. A pancake structure was observed on surface of the coating produced in the base electrolyte, while a foam feature along with some volcano-like areas was detected on the surface of the coatings produced in the presence of KMnO4. The KMnO4 changed the discharge type leading to diminish the pores at the metal/coatin…
The corrosion and tribocorrosion resistance of PEO composite coatings containing α-Al2O3 particles on 7075 Al alloy
2018
Abstract Plasma electrolytic oxidation (PEO) of 7075 Al alloy was carried out in silicate base electrolyte containing 200 nm diameter α-Al2O3 particles for producing composite coatings. The process was performed under a soft-sparking regime using a pulsed bipolar signal with several concentrations of α-Al2O3 particles. It was found that the incorporation of α-Al2O3 particles into the coating did not significantly alter the thickness and roughness of the coating. However, the α-Al2O3 particles were detected on surface of the composite coatings. Corrosion tests showed significant improvement in corrosion performance of the composite coatings due to the efficient pore blocking provided by α-Al…
Applicability of a Polymerized Ionic Liquid/Carbon Nanoparticle Composite Electrolyte to Reductive Cyclization and Dimerization Reactions
2016
Abstract Recently, a reusable polymerized ionic liquid/carbon nanoparticle composite electrolyte was developed and effectively applied to a variety of oxidative transformations. The efficient recovery of the composite material and its application in subsequent electroorganic conversions without sacrificing yield adds to the sustainability of the protocol. Herein, we describe our efforts to expand the operational window of the composite electrolyte to include cathodically initiated processes occurring at potentials up to −2.6 V. The results indicate that the composite electrolyte is applicable to reductive processes, but the scope of transformations appears to be limited.
Large, Highly Modular Narrow-Gap Electrolytic Flow Cell and Application in Dehydrogenative Cross-Coupling of Phenols
2019
The successive scale-up of electrochemical reactions is crucial with regard to the implementation of technical electro-organic syntheses. Therefore, we developed a scalable modular parallel-plate e...
Active Molybdenum‐Based Anode for Dehydrogenative Coupling Reactions
2018
A new and powerful active anode system that can be operated in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) has been discovered. In HFIP the molybdenum anode forms a compact, conductive, and electroactive layer of higher-valent molybdenum species. This system can replace powerful but stoichiometrically required MoV reagents for the dehydrogenative coupling of aryls. This electrolytic reaction is more sustainable and allows the conversion of a broad scope of activated arenes.
Novel TiO2-WO3 self-ordered nanotubes used as photoanodes: Influence of Na2WO4 and H2O2 concentration during electrodeposition
2021
[EN] Hybrid TiO2-WO3 nanostructures has been synthesized by electrochemical anodization under controlled hydrodynamic conditions followed by electrodeposition in the presence of different contents of Na2WO4 (5, 15 and 25 mM) and H2O2 (20, 30 and 40 mM). The influence of the electrolyte used for electrodeposition on the morphology, crystalline structure and photoelectrochemical response for water splitting has been evaluated through Field Emission Electronic Microscopy, High-Resolution Transmission Electron Microscopy, Confocal Raman Spectroscopy, Grazing Incidence X Ray Diffraction, X-Ray Photoelectron Spectroscopy, Atomic Force microscopy and photocurrent versus potential measurements. Add…
Preparation of conductive PDDA/(PEDOT:PSS) multilayer thin film: influence of polyelectrolyte solution composition.
2014
Abstract Self-assembled multilayer films made of PEDOT:PSS poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) and PDDA poly(diallyldimethylammonium chloride) were prepared using layer-by-layer method. In order to modify the growth regime of the multilayer, to fabricate an electrical conductive film and to control its thickness, the effects of pH, type of electrolyte, ionic strength and polyelectrolyte concentration were investigated. Optical reflectometry measurements show that the pH of the solutions has no effect on the film growth while the adsorbed amount increases more rapidly when BaCl2 is used instead of NaCl as electrolyte. An increase in the ionic strength (with NaCl) induces…
Impedance characterization of the electrochemical environment under a polymer film artificially delaminated
2008
International audience; Knowledge of the electrical conductivity of the zone under a delaminated paint film is one necessary input parameter for the simulation of electrochemically driven underpaint corrosion. In this work, a microelectrode array system has been developed, tested, and applied to measure the spatial distribution of resistivity in the delaminated zone along the metal/polymer interface. The experimental device consists of a linear array of six 100 m diameter stainless steel microelectrodes (100 m in diameter) embedded in a steel substrate. A polymer coatingwas applied and an artificial "delaminated zone"was created using the laser-induced decohesion technique. The electrochemi…
Interface Solid-State Reactions in La0.8Sr0.2MnO3/Ce0.8Sm0.2O2 and La0.8Sr0.2MnO3/BaCe0.9Y0.1O3 Disclosed by X-ray Microspectroscopy
2019
The stability of the electrode/electrolyte interface is a critical issue in solid-oxide cells working at high temperatures, affecting their durability. In this paper, we investigate the solid-state chemical mechanisms that occur at the interface between two electrolytes (Ce0.8Sm0.2O2, SDC, and BaCe0.9Y0.1O3, BCY) and a cathode material (La0.8Sr0.2MnO3, LSM) after prolonged thermal treatments. Following our previous work on the subject, we used X-ray microspectroscopy, a technique that probes the interface with submicrometric resolution combining microanalytical information with the chemical and structural information coming from space-resolved X-ray absorption spectroscopy. In LSM/BCY, the …