Search results for "electromagnetic"
showing 10 items of 1595 documents
On thermal influence of laser beam irradiation on optical absorption of amorphous as-evaporated As2S3 films
1998
Abstract Photoinduced changes of the optical absorption in amorphous as-evaporated As 2 S 3 thin films are studied. Before the measurements films were kept at dark for more than two years. The long storage time ensured that the relaxational structural changes caused by the deposition process were absent. As a light source a CW unfocused 488.0 nm Ar laser line was used. The intensity of the laser beam was varied from rather low intensity values up to intensities which raised the temperature of the films above the glass transition temperature. Based on the behavior of the saturation values of the absorption we were able to state that the exposed As 2 S 3 films started to polymerize at 63–69°C…
Visible to vacuum-UV range optical absorption of oxygen dangling bonds in amorphous SiO2
2011
Synthetic silica glass with an optical absorption spectrum dominated by oxygen dangling bonds (nonbridging oxygen hole centers, or NBOHCs) and having negligible (1%) contribution from the usually copresent Si dangling bonds (E\ensuremath{'}-centers), was prepared by room temperature ultraviolet photobleaching of high SiOH content (``wet'') silica, irradiated by F${}_{2}$ laser (7.9 eV) at $T$ = 80 K. This allowed us to obtain the up-to-now controversial optical absorption spectrum of NBOHC in the ultraviolet and vacuum-ultraviolet (UV-VUV) region of the spectrum and to show that it is semicontinuous from 4 to 7.8 eV and cannot be represented by a pair of distinct Gaussian bands. Since NBOHC…
Dual-Comb Spectroscopy With Frequency-Agile Lasers
2015
Multiheterodyne frequency comb spectroscopy without mode-locked lasers is reported in the near-infrared C and L telecommunication bands. The system without active stabilization combines high signal-to-noise ratio, rapid tuning and moderate multiplex spectral span.
Transient absorption with a femtosecond tunable excitation pump reveals the emission kinetics of color centers in amorphous silica.
2021
We report a set of femtosecond (fs) transient absorption (TA) measurements following the dynamics of the so-called nonbridging oxygen hole center in silica, a model color center in wide bandgap amorphous solids, characterized by a very large Stokes shift between the UV excitation and its associated red emission at 1.9 eV. The changes in the TA spectrum were probed in the UV-visible range at various delays after photoexcitation and analyzed as a function of the UV excitation energy, in single-photon absorption conditions. The combination of the experiments helps to clarify the defect photocycle, highlighting how TA measurements with tunable UV excitation could represent a powerful tool to in…
Analysis of the electromagnetic radiation generated by a multipactor discharge occurring within a microwave passive component
2010
International audience; Multipactoring is a non-linear phenomenon that appears in highpower microwave equipments operating under vacuum conditions and causes several undesirable effects. In this manuscript, a theoretical and experimental study of the RF spectrum radiated by a multipactor discharge, occurring within a realistic microwave component based on rectangular waveguides, is reported. The electromagnetic coupling of a multipactor current to the fundamental propagative mode of a uniform waveguide has been analyzed in the context of the microwave network theory. The discharge produced under a single-carrier RF voltage regime has been approached as a shunt current source exciting such a…
Characterization of Different Cable Ferrite Materials to Reduce the Electromagnetic Noise in the 2–150 kHz Frequency Range
2018
The gap of standardization for conducted and field coupled electromagnetic interferences (EMI) in the 2–150 kHz frequency range can lead to Electromagnetic Compatibility (EMC) problems. This is caused by power systems such as Pulse Width Modulation (PWM) controlled rectifiers, photovoltaic inverters or charging battery units in electric vehicles. This is a very important frequency spectral due to interferences generated in a wide range of devices and, specifically, communication problems in the new technologies and devices incorporated to the traditional grid to convert it into a Smart Grid. Consequently, it is necessary to provide new solutions to attenuate this kind of interference, which…
Improving the Efficiency of NFC Systems Through Optimizing the Sintered Ferrite Sheet Thickness Selection
2020
The reduction of embedded portable devices involves a magnetic field interference problem when it integrates near field communication (NFC) due to the presence of conductive surfaces, such as ground planes, batteries, or metallic enclosures. Flexible sintered ferrite sheets (FSFS) represent an interesting shielding solution to prevent electromagnetic interferences problems related to NFC, thanks to their ability to control the magnetic flux. The characterization of FSFS effectiveness is analyzed as a function of the sheet thickness in this contribution. This is performed with the aim of determining which is the optimum thickness value to retune an NFC antenna to its original operation frequ…
Defect characterization in Al welded joints by non-contact Lamb wave technique
2006
Abstract The use of air-coupled sensors to detect flaws in Al welded joints and the advantage of Lamb wave for their characterization has been proved. Ultrasonic waves were generated by a pulsed laser and by contact angle-beam transducer, and received by an air-coupled capacitive transducer. Laser-based configuration was used to quickly locate the defect, whereas the angle-beam contact probe configuration to characterize it thanks to the dispersive behavior of Lamb waves. Guided waves allow inspection of the complete thickness with only one scan, permitting to detect and to size both internal and surface defects; their high flexibility in the measurement is due to the various parameters cha…
Study of magnesium and aluminum alloys absorption coefficient during Nd:YAG laser interaction
2007
International audience; In laser processes, the absorption factor of laser Nd:YAG by metals plays a very important role. In order to model laser welding, we need to know its evolution during the process. The theoretical calculation does not enable the prediction of the absorption factor in the case of a keyhole mode. It is difficult to predict the effect of plasma and recoil pressure on the shape of the keyhole. In this paper, an integrating sphere is used to determine the absorption factor during the laser process, which is carried out on two types of magnesium alloys (WE43 and RZ5) and an aluminum alloy. We obtain the evolution in time of the absorption factor according to different steps…
Non-destructive technique to detect local buried defects in metal sample by scanning microwave microscopy
2012
International audience; Based on the skin effect, our recent developments using scanning microwave microscopy lead to propose a non-destructive method to detect located buried defect in metal samples like stainless steel. A 3D tomography is possible by taking advantage of microwave measurement, using a vector network analyzer in bandwidth frequencies, and the nanometer resolution positioning capabilities with atomic force microscopy. At each used frequency, an incident electromagnetic wave is sent to the sample and the reflected wave gives information on a specific depth layer in the material. With diagnostic tools of nanotechnologies (SEM. AFM, etc.), different stainless steel samples (fro…