Search results for "electron"

Characteristic Kα emission of electron cyclotron resonance ion source plasmas

2018

This thesis presents the results of an investigation of the volumetric Kα emission rate/inner shell ionization rate from an Electron Cyclotron Resonance Ion Source (ECRIS) plasma tuned predominantly for high charge state ion production. The experimental work include four complimentary studies covering the influence of a parametric sweep of the four source tune parameters i.e microwave power, neutral gas flow, biased disc voltage and magnetic field on the volumetric Kα emission rate, an investigation into the gas mixing effect, an investigation into the effectiveness of double-frequency heating mode and finally an investigation into microwave induced electron losses (relative and direct) from th…

Biocompatibility and Antibacterial Properties of ZnO-Incorporated Anodic Oxide Coatings on TiZrNb Alloy

2020

In a present paper, we demonstrate novel approach to form ceramic coatings with incorporated ZnO nanoparticles (NPs) on low modulus TiZrNb alloy with enhanced biocompatibility and antibacterial parameters. Plasma Electrolytic Oxidation (PEO) was used to integrate ZnO nanoparticles (average size 12&ndash

Recent progress on the superconducting ion source VENUS.

2012

The 28 GHz Ion Source VENUS (versatile ECR for nuclear science) is back in operation after the superconducting sextupole leads were repaired and a fourth cryocooler was added. VENUS serves as an R&D device to explore the limits of electron cyclotron resonance source performance at 28 GHz with its 10 kW gryotron and optimum magnetic fields and as an ion source to increase the capabilities of the 88-Inch Cyclotron both for nuclear physics research and applications. The development and testing of ovens and sputtering techniques cover a wide range of applications. Recent experiments on bismuth demonstrated stable operation at 300 eμA of Bi31+, which is in the intensity range of interest for hig…

Aluminum tri-isopropoxide as an alternative precursor for atomic layer deposition of aluminum oxide thin films

2019

Due to the safety challenges associated with the use of trimethylaluminum as a metal precursor for the deposition of alumina, different chemicals have been investigated over the years to replace it. The authors have investigated the use of aluminum tri-isopropoxide (TIPA) as an alternative alkoxide precursor for the safe and cost-effective deposition of alumina. In this work, TIPA is used as a stable Al source for atomic layer deposition (ALD) of Al2O3 when different oxidizing agents including water, oxygen plasma, water plasma, and ozone are employed. The authors have explored the deposition of Al2O3 using TIPA in ALD systems operating in vacuum and atmospheric pressure conditions. For the…

Photoelectron emission experiments with ECR-driven multi-dipolar negative ion plasma source

2017

Photoelectron emission measurements have been performed using a 2.45 GHz ECR-driven multi-dipolar plasma source in a low pressure hydrogen discharge. Photoelectron currents induced by light emitted from ECR zone and H− production region are measured from Al, Cu, Mo, Ta, and stainless steel (SAE 304) surfaces as a function of microwave power and neutral hydrogen pressure. The total photoelectron current from the plasma chamber wall is estimated to reach values up to 1 A for 900 W of injected microwave power. It is concluded that the volumetric photon emission rate in wavelength range relevant for photoelectron emission is a few times higher in arc discharge. peerReviewed

VUV emission spectroscopy combined with H- density measurements in the ion source Prometheus I

2016

“Prometheus I” is a volume H− negative ion source, driven by a network of dipolar electron cyclotron resonance (ECR; 2.45 GHz) modules. The vacuum-ultraviolet (VUV) emission spectrum of low-temperature hydrogen plasmas may be related to molecular and atomic processes involved directly or indirectly in the production of negative ions. In this work, VUV spectroscopy has been performed in the above source, Prometheus I, both in the ECR zones and the bulk (far from ECR zones and surfaces) plasma. The acquired VUV spectra are correlated with the negative ion densities, as measured by means of laser photodetachment, and the possible mechanisms of negative ion production are considered. The well-e…

Fracture and fatigue of titanium narrow dental implants: New trends in order to improve the mechanical response

2019

Sixty-four fractured commercially pure titanium (cp-Ti) narrow dental implants (NDIs) with similar macrogeometry and connection designs were studied after different implantation times in humans in order to determine their reliability and to evaluate the causes of the fracture. These NDIs were compared with other similar implants, made with alloyed titanium with 15% Zr and with 12% strained titanium. Original implants were tested under static and fatigue conditions, simulating the tri-axial loads in the mouth by means of a Bionix hydraulic test machine. Fractography was studied using field-emission scanning electron microscopy (FSEM). The results showed that cp-Ti NDI exhibits low strength f…

Solution processes for plastic thin film transistors

2009

The role of polaronic states in the enhancement of CO oxidation by single-atom Pt/CeO2

2023

Single Atom Catalysts (SACs) have shown that the miniaturization of the active site implies new phenomena like dynamic charge transfer between isolated metal atoms and the oxide. To obtain direct proof of this character is challenging, as many experimental techniques provide averaged properties or have limitations with poorly conductive materials, leaving kinetic measurements from catalytic testing as the only reliable reference. Here we present an integrated Density Functional Theory-Microkinetic model including ground and metastable states to address the reactivity of Pt1/CeO2 for CO oxidation. Our results agree with experimentally available kinetic data in the literature and show that CO…

Active lighting applied to three-dimensional reconstruction of specular metallic surfaces by polarization imaging

2006

International audience; In the field of industrial vision, the three-dimensional inspection of highly reflective metallic objects is still a delicate task. We deal with a new automated three-dimensional inspection system based on polarization analysis. We first present an extension of the shape-from-polarization method for dielectric surfaces to metallic surfaces. Then, we describe what we believe to be a new way of solving the ambiguity concerning the normal orientation with an active lighting system. Finally, applications to shape-defect detection are discussed, and the efficiency of the system to discriminate defects on specular metallic objects made by stamping and polishing is presente…