Search results for "electronics"
showing 10 items of 4340 documents
Cladding-Pumped Erbium/Ytterbium Co-Doped Fiber Amplifier for C-Band Operation in Optical Networks
2021
Space-division multiplexing (SDM) attracts attention to cladding-pumped optical amplifiers, but they suffer from a low pump power conversion efficiency. To address this issue, ytterbium (Yb3+) and erbium (Er3+) co-doping is considered as an effective approach. However, it changes the gain profile of Er3+-doped fiber amplifiers and induces the gain difference between optical wavelengths in the C-band, significantly limiting the effective band of the dense wavelength-division multiplexed (DWDM) system. This paper is devoted to a detailed study of a cladding-pumped Er3+/Yb3+ co-doped fiber amplifier (EYDFA) through numerical simulations aiming to identify a configuration, before assembling a s…
Mechanical behaviour and failure modes of metal to composite adhesive joints for nautical applications
2010
In this paper, the influence of several parameters on the mechanical behaviour and failure modes of hybrid bonded joints aluminium/composite was investigated. Particularly, the effects of metallic surface condition, adhesive properties and thickness on single-lap joint resistance were analysed. To these aims, two adhesives were used and, for each adhesive, two different adhesive thicknesses (0.5 and 1.5 mm) have been investigated. Furthermore, two sets of joints for each adhesive kind and thickness were investigated: the former was obtained using aluminium blanks which were previously mechanically treated with sandpaper (P60) and the latter using aluminium treated with sandpaper and with pr…
Effect of Chemical Etching on Adhesively Bonded Aluminum AA6082
2007
The efforts of new automotive industry are mainly directed towards the substitution of aluminum for steel in the body structure because the aluminum structures are lighter than traditional steel ones and meet the requirements, in terms of both vehicle design and manufacture. However, this substitution is not so automatic, but it is important to study the material properties and the structure design, focusing the attention on the methods of joining. Welding, typical technique to joint steel parts, is particularly difficult when applied on aluminum ones and then, in many cases, the adhesive bonding is preferred. To optimise the joint performances it is necessary to pre-treat the metal surface…
Effect of Ni content on the structure and hydrogenation property of mechanically alloyed TiMgNix ternary alloys
2017
Abstract In this study, TiMgNix samples (x = 0.2, 0.4, 0.6, 0.8, 1) have been prepared by mechanical alloying using a planetary high-energy ball mill. The structural transformations were characterized by XRD and indicated that all the as-milled TiMgNix alloys consist of mixtures of crystalline Mg and amorphous Ti-Ni-(Mg) phase. TEM analyses also show that nanocrystallites and amorphous phases coexist in the as-milled TiMgNi alloy. Electrochemical test shows that the TiMgNi composition yields the highest discharge capacity. The discharge capacities and activation properties of TiMgNix alloys linearly increase with increasing Ni content. The MgTiNi0.8 composition boasts the best cycling prope…
Investigating the mechanical properties of GeSn nanowires.
2019
Germanium tin (GeSn) has been proposed as a promising material for electronic and optical applications due to the formation of a direct band-gap at a Sn content >7 at%. Furthermore, the ability to manipulate the properties of GeSn at the nanoscale will further permit the realisation of advanced mechanical devices. Here we report for the first time the mechanical properties of GeSn nanowires (7.1-9.7 at% Sn) and assess their suitability as nanoelectromechanical (NEM) switches. Electron microscopy analysis showed the nanowires to be single crystalline, with surfaces covered by a thin native amorphous oxide layer. Mechanical resonance and bending tests at different boundary conditions were use…
Thermostimulated luminescence of plasma electrolytic oxidation coatings on 6082 aluminium surface
2019
Financial support provided by Scientific Research Project for Students and Young Researchers Nr. SJZ/2016/12 realized at the Institute of Solid State Physics, University of Latvia is greatly acknowledged. Authors are grateful to R. Ignatans for measurements and analysis of XRD spectra and ElGoo Tech ltd. for providing PEO equipment.
Magnetic Properties of Quinoidal Oligothiophenes: More Than Good Candidates for Ambipolar Organic Semiconductors?
2006
A series of quinoidal oligothiophenes have been investigated by means of solid-state Fourier-transform (FT)-Raman and electron spin resonance (ESR) spectroscopies complemented with density functional theory calculations. FT-Raman spectra recorded as a function of temperature show that, upon laser irradiation, the molecules undergo a reversible structural evolution from a quinoid-type pattern at low temperature to an aromatic-type pattern at high temperature. Moreover, ESR spectra show that a portion of these compounds exists in a biradical state at room temperature. These seemingly disconnected findings and others, such as conformational isomerism, are consistently explained by the consider…
Parameters of microdischarges occuring at surfaces of repolarized ferroelectrical materials
1993
Parameters of the microdischarges occuring at the surfaces of the repolarized ferroelectric materials have been investigated. It has been found that in the case of BaTiO3ceramic the number of microdischarges increases linearly with increasing repolarizing voltage Upp, the photoelectric parameters of individual discharges being unchanged. The photoelectric and current parameters for system with TGS are very similar but the dependence of the amplitude of the current pulses on the repolarizing voltage differs distinctly from that for BaTiO3.
Energy resolution and throughput of a new real time digital pulse processing system for x-ray and gamma ray semiconductor detectors
2013
New generation spectroscopy systems have advanced towards digital pulse processing (DPP) approaches. DPP systems, based on direct digitizing and processing of detector signals, have recently been favoured over analog pulse processing electronics, ensuring higher flexibility, stability, lower dead time, higher throughput and better spectroscopic performance. In this work, we present the performance of a new real time DPP system for X-ray and gamma ray semiconductor detectors. The system is based on a commercial digitizer equipped with a custom DPP firmware, developed by our group, for on-line pulse shape and height analysis. X-ray and gamma ray spectra measurements with cadmium telluride (Cd…
Non-destructive technique to detect local buried defects in metal sample by scanning microwave microscopy
2012
International audience; Based on the skin effect, our recent developments using scanning microwave microscopy lead to propose a non-destructive method to detect located buried defect in metal samples like stainless steel. A 3D tomography is possible by taking advantage of microwave measurement, using a vector network analyzer in bandwidth frequencies, and the nanometer resolution positioning capabilities with atomic force microscopy. At each used frequency, an incident electromagnetic wave is sent to the sample and the reflected wave gives information on a specific depth layer in the material. With diagnostic tools of nanotechnologies (SEM. AFM, etc.), different stainless steel samples (fro…