Search results for "electronics"
showing 10 items of 4340 documents
Study of the use of methanol-filled Er-doped suspended-core fibres in a temperature-sensing ring laser system
2013
We report on an experimental/numerical investigation into the use of methanol-filled Er-doped suspended-core fibres (SCFs) in temperature-sensing ring laser systems. We have adopted a ring laser configuration that includes an Er-doped SCF as a temperature-dependent attenuator (TDA) with a step-index Er-doped fibre (EDF) as the laser active medium. The laser performance dependence on the temperature was measured both in continuous wave (CW) and transient regimes. CW laser output power and build-up time values are compared with those of similar laser systems based on other types of Er-doped PCFs or using other laser configurations. A notable variation of 0.73% °C−1 was achieved in CW operatio…
A novel noise figure and gain test set for microwave devices
2002
A new instrument for the measurement of noise and gain of microwave devices is presented. It differs from the commercial ones in the accomplishment of the gain measurement and is also useful for measuring mismatched devices such as transistors, The instrument is driven via HP-IB by a PC and a user-friendly virtual panel is designed to perform all the required operations. Also included is the possibility of removing the second-stage noise contribution and correcting various sources of error (source ENR variations, temperature variations, etc.). The test set provides a very good accuracy for both matched and mismatched devices, usually limited by source ENR accuracy and step attenuator repeat…
Artifacts and Errors in Cross-Spectrum Phase Noise Measurements : Invited lecture
2021
Inserting an attenuator between the oscillator under test and the phase noise analyzer, one expects that the white phase noise increases monotonically with the attenuation. By contrast, we observe that with some oscillators the white noise has sharp minimum for a given value of the attenuation, which clearly indicates problem. With other oscillators, it increases monotonically with the attenuation, but the values are not consistent with the thermal energy introduced by the attenuator. In both cases artifacts are present, which takes the form of a sharp notch in the spectrum, occurring where the white FM noise crosses the white PM noise. Such anomalous behavior is the tip of the iceberg, and…
Graphene as a tunable resistor
2014
We present the design of a graphene-based electronically tuneable microstrip attenuator operating at a frequency of 5 GHz. The use of graphene as a variable resistor is discussed and the modelling of its electromagnetic properties at microwave frequencies is fully addressed. The design of the graphene-based attenuator is described. The structure integrates a patch of graphene, whose characteristics can range from being a fairly good conductor to a highly lossy material, depending on the applied voltage. By applying the proper voltage through two high-impedance bias lines, the surface resistivity of graphene can be modified, thereby changing the insertion loss of the microstrip attenuator.
Iron deposition on TiO2(110): effect of the surface stoichiometry and roughness
1999
Abstract Characterizations of ultra-thin iron films deposited on TiO 2 (110) surfaces with different stoichiometries, roughnesses and crystallinities have been carried out by X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES). For a high initial roughness of the substrate, a 2D growth mode is observed up to three monolayers. But, if the initial roughness is low, clusters grow on the TiO 2 surface. Whatever the initial surface stoichiometry, electronic exchanges occur between titanium and iron leading to a reduction of titanium and an oxidation of iron. This interaction between iron and titanium dioxide surface takes place only at the interface between the metal and…
Fabrication of layered nanostructures by successive electron beam induced deposition with two precursors: protective capping of metallic iron structu…
2011
We report on the stepwise generation of layered nanostructures via electron beam induced deposition (EBID) using organometallic precursor molecules in ultra-high vacuum (UHV). In a first step a metallic iron line structure was produced using iron pentacarbonyl; in a second step this nanostructure was then locally capped with a 2-3 nm thin titanium oxide-containing film fabricated from titanium tetraisopropoxide. The chemical composition of the deposited layers was analyzed by spatially resolved Auger electron spectroscopy. With spatially resolved x-ray absorption spectroscopy at the Fe L₃ edge, it was demonstrated that the thin capping layer prevents the iron structure from oxidation upon e…
A CEMS/AES study of the passivation of iron
1989
The passivation of iron and steel (DIN 1623) was studied by integral and depth selective conversion electron Mossbauer spectroscopy and Auger electron spectroscopy. Thickness and phase composition of the passive layer formed in sulphate solution and in a phosphate buffer were determined in dependence on the anodic potential and the duration of the passivating procedure. The experimental results lead to the conclusion that not the whole oxidic layer is responsible for the passivity but only a very thin intermediate layer formed between the cubic substrate and the rhombic oxide (γ-FeOOH) cover.
The growth of oxide platelets on nickel in pure oxygen. II. Surface analyses and growth mechanism
1993
The structural properties of NiO platelets emerging from a primary oxide layer by oxidation of pretreated nickels in pure oxygen between 650 and 800° C have been investigated in relation with the initial metallic layers and the primary oxide. Surface composition and segregation of impurities were also studied by X-ray photoelectron spectroscopy and Auger electron spectroscopy. Textural properties and structural orientation of both the primary oxide layer and the platelets were analyzed by X-ray diffraction and transmission electron microscopy. Platelets grew along {111} planes, leading to elliptical or semicircular bicrystals. The driving force for the present type of growth originates from…
Technical Note:Study of the Cl−-Induced Breakdown of the Passive Layer on Steel
1991
Abstract The Cl−-induced breakdown of the passive layer on a standard steel has an induction time that increases in a nearly linear fashion with the previous holding time (at the passivation potent...
Effect of the surface stoichiometry on the interaction of Mo with TiO2 (110)
2000
Abstract Molydenum has been deposited at room temperature on (110) TiO2 surfaces with different stoichiometries, roughnesses and crystallinities. Whatever the substrate preparation is, in-situ Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) studies as well as ex-situ atomic force microscopy (AFM) and reflexion high-energy electron diffraction (RHEED) studies reveal a Stranski–Krastanov growth mode: the completion of three monolayers followed by islands growth is observed in every case. The three monolayers are always composed of amorphous molybdenum oxide with an oxidation state of molybdenum less than IV. The oxidation of the molybdenum layers generates Ti3+ an…