Search results for "engineering.material"
showing 10 items of 2352 documents
Spark plasma sintering of cobalt ferrite nanopowders prepared by coprecipitation and hydrothermal synthesis.
2007
International audience; Cobalt ferrite exhibits a high coercivity at room temperature and a strong magnetic anisotropy compared to the other spinel ferrites and, consequently appears as an interesting material for permanent magnets and high-density recording. The magnetic properties depend also on the crystallite size. In order to keep the powder properties in a bulk material, dense nanostructured cobalt ferrite has to be sintered. A field activated sintering process like spark plasma sintering (SPS) may be promising for such challenge. The present paper deals with: (i) the preparation of cobalt ferrite by two methods: coprecipitation and hydrothermal synthesis in supercritical water; (ii) …
Structural and Vibrational Properties of Corundum-type In2O3 Nanocrystals under Compression
2017
[EN] This work reports the structural and vibrational properties of nanocrystals of corundum-type In2O3 (rh-In2O3) at high pressures by using angle-dispersive x-ray diffraction and Raman scattering measurements up to 30 GPa. The equation of state and the pressure dependence of the Raman-active modes of the corundum phase in nanocrystals are in good agreement with previous studies on bulk material and theoretical simulations on bulk rh-In2O3. Nanocrystalline rh-In2O3 showed stability under compression at least up to 20 GPa, unlike bulk rh-In2O3 which gradually transforms to the orthorhombic Pbca (Rh2O3-III-type) structure above 12 14 GPa. The different stability range found in nanocrystallin…
Trends of Organic Electrosynthesis by Using Boron-Doped Diamond Electrodes
2019
The electro-organic synthesis is currently experiencing a renaissance due to the tremendous contributions of various electrocatalytic materials as well as the use of electric current as an inexpensive and suitable reagent to drive the electrosynthetic transformations, avoiding conventional chemical oxidizers or reducing agents. Consequently, electrosynthesis has a significant technical impact, because these processes can be easily scaled up, benefiting from advantages such as versatility, environmental compatibility (possibility of recovering and recycling non-converted substrates), automation (switching on or off electric current), inherent safety and potential cost effectiveness among oth…
Influence of the Mean Load Value in Fatigue Block Loading on Strains
2014
This paper presents the results of the fatigue tests of the specimens made from S3555 steel and aluminum alloy AlCu4MgSi subjected to bending block loading with mean load value. The influence of the changes of the mean load conditions was investigated. During the tests strains were registered and relation between the load and the strains was analyzed. In the case of S355 steel it was observed, that additional hardening occurs when higher value of the mean load is applied at the beginning of the block loading. Other case, when the mean load was increased from zero to maximum, a creep effect of the material was registered. For the specimens made from aluminum alloy similar processes were not …
Halloysite nanotubes/pluronic nanocomposites for waterlogged archeological wood: thermal stability and X-ray microtomography
2020
Filling a polymer with halloysite nanotubes is considered a promising strategy to generate nanocomposites with tailored physicochemical properties. We have focused our attention on pluronic block copolymer/halloysite nanocomposites prepared by melt blending. The effect of composition on thermal stability and polymer crystallinity was investigated by thermogravimetry and differential scanning calorimetry. Electron microscopy was used to monitor the nanoparticle distribution in the polymeric matrix. The pluronic thermal stability is reduced by the clay nanoparticles. Concerning the polymer crystallinity, it is slightly decreased even if the melting temperature is lowered by halloysite. Furthe…
Mechanical behavior of single-layer ceramized zirconia abutments for dental implant prosthetic rehabilitation
2013
Objectives: This study was undertaken to characterize the mechanical response of bare (as-received) and single-layer ceramized zirconia abutments with both internal and external connections that have been developed to enhanced aesthetic restorations. Material and Methods: Sixteen zirconia implant abutments (ZiReal Post®, Biomet 3i, USA) with internal and external connections have been analyzed. Half of the specimens were coated with a 0.5mm-thick layer of a low-fusing fluroapatite ceramic. Mechanical tests were carried out under static (constant cross-head speed of 1mm/min until fracture) and dynamic (between 100 and 400N at a frequency of 1Hz) loading conditions. The failure location was i…
Hot-Carrier Generation in Plasmonic Nanoparticles: The Importance of Atomic Structure
2020
Metal nanoparticles are attractive for plasmon-enhanced generation of hot carriers, which may be harnessed in photochemical reactions. In this work, we analyze the coherent femtosecond dynamics of photon absorption, plasmon formation, and subsequent hot-carrier generation through plasmon dephasing using first-principles simulations. We predict the energetic and spatial hot-carrier distributions in small metal nanoparticles and show that the distribution of hot electrons is very sensitive to the local structure. Our results show that surface sites exhibit enhanced hot-electron generation in comparison to the bulk of the nanoparticle. While the details of the distribution depend on particle s…
Micro- and nano-diamond particles in carbon spherules found in soil samples
2008
Carbonaceous spherules of millimeter size diameter and found in the upper soils throughout Europe are investigated by TEM, including SAED, HRTEM and EELS, and Raman spectroscopy. The spherules consist primarily of carbon and have an open cell-like internal structure. Most of the carbon appears in an amorphous state, but different morphologies of nano- and microdiamond particles have also been discovered including flake shapes. The latter observation, together with the original findings of some of these spherules in crater-like structures in the landscape and including severely deformed rocks with some spherules being embedded in the fused crust of excavated rocks, points towards unique cond…
Influence of calcination on the structural properties of earth abundant Cu2ZnSnS4
2021
Abstract In the present work, we report on the synthesis of nano-crystalline kesterite copper zinc tin sulfide (CZTS) in powder form and the post-annealing process at high temperatures (calcination), and study their physical properties. We have successfully synthesized CZTS by direct fusion, and the resulting material was crushed to obtain a fine powder. Then, the resulting powder was calcined at high temperatures: 800–1000 ∘C. The calcined samples have been characterized with a number of different structural: X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and optical techniques: photoluminescence (PL), Raman and diffuse reflectance spectr…
Thermoelectric properties of spark plasma sintered composites based on TiNiSn half-Heusler alloys
2011
Half-Heusler (HH) and especially TiNiSn-based alloys have shown high potential as thermoelectric (TE) materials for power generation applications. The reported transport properties show, however, a significant spread of results, due mainly to the difficulty in fabricating single-phase HH samples in these multicomponent and multiphased systems. In particular, little attention has been paid to the influence of the various minority phases on the TE performance of these compounds. A clear understanding of these issues is mandatory for the design of improved and stable TE HH-based composites. This study examines the structural and compositional influence of the residual metallic (Sn) and interme…