Search results for "fouling"

Sub-critical long-term operation of industrial scale hollow-fibre membranes in a submerged anaerobic MBR (HF-SAnMBR) system

2012

The aim of this study was to evaluate the long-term performance of hollow-fibre (HF) membranes used to treat urban wastewater in a submerged anaerobic MBR when operating sub-critically. To this end, a demonstration plant with two industrial scale HF ultrafiltration membrane modules was operated under different conditions. The main factor affecting membrane performance was the concentration of mixed liquor total solids (MLTS). The reversible fouling rate remained low even when MLTS levels (about 25 g L−1) in the membrane tank were high. No chemical cleaning was conducted whilst operating the plant for more than one year because no irreversible fouling problems were detected. The almost compl…

Analisi della fase di start-up di un bioreattore a membrana

2006

L’applicazione dei sistemi MBR, pur garantendo elevati rendimenti di rimozione, è ancora oggi limitata, a causa di alcuni fattori che ne condizionano il funzionamento. Tra questi, uno dei principali è il fouling dovuto ai fenomeni di sporcamento della membrana da parte della sospensione biologica. Nella memoria si riportano i primi risultati di uno studio che ha avuto l’obiettivo di definire l’evoluzione e l’influenza del fouling sul processo di filtrazione durante la fase di avviamento dell’impianto, avvenuto senza inoculo iniziale di fango. La sperimentazione è stata condotta in un impianto pilota costituito da un bioreattore all’interno del quale è stato installato il modulo di membrane …

Analisi sperimentale e modellistica di formazione del fouling delle membrane nei sistemi MBR

2012

Removal of carbon and nutrients from wastewater in a moving bed membrane biofilm reactor: the influence of the sludge retention time

2016

A University of Cape Town (UCT) pilot plant combining both membrane bioreactor (MBR) and moving bed biofilm reactor (MBBR) technology was monitored. Three experimental Phases were carried out by varying the mixed liquor sludge retention time (SRT) (indefinite, 30 and 15 days, respectively). The system performance has been investigated during experiments in terms of: organic carbon, nitrogen and phosphorus removal, biokinetic/stoichiometric constants, membrane fouling tendency and sludge dewaterability. The observed results showed that by decreasing the SRT the UCT pilot plant was able to maintain very high total COD removal efficiencies, whilst the biological COD removal efficiency showed a…

A Brief Review on the Resistance-in-Series Model in Membrane Bioreactors (MBRs)

2019

The cake layer deposited on the membrane modules of membrane bioreactors (MBRs), especially under a submerged configuration, represents a relevant and fundamental mechanism deeply influencing the development of membrane fouling. It negatively affects the total resistance to filtration, while exerting a positive effect as a “pre-filter„ promoting the “dynamic membrane„ that protects the physical membrane from internal fouling. These two opposite phenomena should be properly managed, where the submerged membranes are usually subjected to a periodical cake layer removal through ordinary (permeate backwashing and air scouring) and/or irregular cleaning actions (manual ph…

Nanozymes in Nanofibrous Mats with Haloperoxidase-like Activity To Combat Biofouling.

2018

Electrospun polymer mats are widely used in tissue engineering, wearable electronics, and water purification. However, in many environments, the polymer nanofibers prepared by electrospinning suffer from biofouling during long-term usage, resulting in persistent infections and device damage. Herein, we describe the fabrication of polymer mats with CeO2–x nanorods that can prevent biofouling in an aqueous environment. The embedded CeO2–x nanorods are functional mimics of natural haloperoxidases that catalyze the oxidative bromination of Br– and H2O2 to HOBr. The generated HOBr, a natural signaling molecule, disrupted the bacterial quorum sensing, a critical step in biofilm formation. The pol…

Fouling dynamics in suspension flows

2002

A particle suspension flowing in a channel in which fouling layers are allowed to form on the channel walls is investigated by numerical simulation. A two-dimensional phase diagram with at least four different behaviors is constructed. The fouling is modeled by attachment during collision with the deposits and by detachment caused by large enough hydrodynamic drag. For fixed total number of particles and small Reynolds numbers, the relevant parameters governing the fouling dynamics are the solid volume fraction of the suspension and the detachment drag force threshold. Below a critical curve in this 2D phase space only transient fouling takes place when the suspension is accelerated from re…

Performance of a polypropylene membrane contactor for the recovery of dissolved methane from anaerobic effluents: Mass transfer evaluation, long-term…

2018

Abstract A polypropylene membrane contactor was used for the recovery of dissolved methane from an anaerobic reactor effluent. Effect of operational parameters, operation mode and fouling on long-term operation was studied using vacuum pressure or N 2 as sweep gas. Results were analyzed based on the mass transfer estimations. Lower performance was observed in the shell-side mode due to the lower liquid velocity and the probable channeling. Membrane pore wetting was observed with the increase in Q L in the vacuum-pressure mode. This was confirmed with mass transfer resistance analysis, resulting in an estimated wetted pore fraction of between 0.25 and 0.53. The highest removal efficiencies w…

Air lift relevance in a side-stream MBR system

2006

Nowadays, two main MBR configurations are developed in wastewater treatment (Fig. 1a and b). The former is based on a side stream membrane module position, it is generally developed for the industrial wastewater treatment because of its compactness even if it requires more energy due to the necessity of using high suspension flow rate recycles throughout the membrane module to minimise fouling rates [1]. With this configuration the membrane maintenance is easy because of the side stream position of the membrane module relatively to the bioreactor. The second configuration is based on the immersion of membrane module directly inside the bioreactor. This configuration is more extensive becaus…

Submicrometer-Sized Roughness Suppresses Bacteria Adhesion.

2020

Biofilm formation is most commonly combatted with antibiotics or biocides. However, proven toxicity and increasing resistance of bacteria increase the need for alternative strategies to prevent adhesion of bacteria to surfaces. Chemical modification of the surfaces by tethering of functional polymer brushes or films provides a route toward antifouling coatings. Furthermore, nanorough or superhydrophobic surfaces can delay biofilm formation. Here we show that submicrometer-sized roughness can outweigh surface chemistry by testing the adhesion of E. coli to surfaces of different topography and wettability over long exposure times (>7 days). Gram-negative and positive bacterial strains are tes…