Search results for "fusion"

IT-supported international outsourcing of software production

2002

A new application for nickel foam in alkaline fuel cells

2009

The use of nickel foam as an electrode substrate in alkaline fuel cells (AFCs) has been investigated for bi-polar cells incorporating an electrically conducting gas diffusion layer. This contribution focuses on the cathode, and draws comparisons between nickel foam and nickel mesh substrates. One of the principal electrocatalysts for the cathodic reduction of oxygen is silver, so an improvement in electrochemical performance was obtained by electroplating the nickel foam with silver. The electrodeposition process was optimised to maximise electrochemical performance with a minimum of silver deposited. Nickel foam, which is less expensive than the usual nickel mesh, appears to be a good subs…

Domain formation in monolayers

1995

For phospholipids at the air/water interface we demonstrate that molecular chirality in some, but not in all, cases influences the domain shapes. In other cases chirality in the head group region can cause a chiral structure considering the tail arrangement. This indicates head group ordering. Minute changes of the molecular structure may change domain morphology from circular to dendritic. This can be related to slight changes of the lattice structure. In case of a dendritic domain the chains are more tilted, the deviation from hexagonal symmetry is more pronounced, and hence the lattice anisotropy is larger. This can be understood also in view of recent simulations considering diffusion-l…

Successful treatment of paraquat poisoning: activated charcoal per os and "continuous hemoperfusion".

1982

AbstractIngestion of paraquat results in an extremely dangerous poisoning. The first aim is to clear the gastrointestinal tract by inducing emesis and performing gastric/gut lavage; as much activated charcoal as possible should be administered per os and as quickly as possible. The best measure to eliminate paraquat from blood and tissue is hemoperfusion with coated activated charcoal; it has to be performed in the sense of “continuous hemoperfusion” about 8 h/d over a period of 2–3 weeks. These measures give a chance to lower the lethality of paraquat poisoning.

Synthesis and preliminary in vivo evaluation of well-dispersed biomimetic nanocrystalline apatites labeled with positron emission tomographic imaging…

2015

In recent years, biomimetic synthetic apatite nanoparticles (AP-NPs), having chemical similarity with the mineral phase of bone, have attracted a great interest in nanomedicine as potential drug carriers. To evaluate the therapeutic perspectives of AP-NPs through the mechanisms of action and organs they interact with, the noninvasive monitoring of their in vivo behavior is of paramount importance. To this aim, here the feasibility to radiolabel AP-NPs ("naked" and surface-modified with citrate to reduce their aggregation) with two positron emission tomographic (PET) imaging agents ([F-18]NaF and Ga-68-NO(2)AP(BP)) was investigated. [F-18]NaF was used for the direct incorporation of the radi…

Influence of oxide substrates on monolayer graphene doping process by thermal treatments in oxygen

2019

Abstract The structural and the electronic properties of monolayer graphene made by chemical vapor deposition and transferred on various oxide substrates ( SiO 2 , Al 2 O 3 , and HfO 2 ) are investigated by Raman Spectroscopy and Atomic Force Microscopy in order to highlight the influence of the substrate on the features of p-doping obtained by O 2 thermal treatments. By varing the treatment temperature up to 400 °C, the distribution of the reaction sites of the substrates is evaluated. Their total concentration and the consequent highest doping available is determined and it is shown that this latter is linked to the water affinity of the substrate. Finally, by varing the exposure time to …

Influence of radiation defects on tritium release parameters from Li2O

1998

Abstract The study of the influence of radiation defects on tritium release behavior from polycrystalline Li2O was performed by simultaneous measurements of the luminescence emission and tritium release. It was found that the radiation defects in Li2O introduced by electron irradiation cause the retention of tritium. It is thought that the tritium recovery is affected by the formation of a Li–T bond, which is tolerant of high temperatures. The retardation of tritium decreases with increasing absorbed dose in the dose range from 50 to 140 MGy. The aggregation of radiation defects at high irradiation doses is considered to be responsible for the decrease of the interaction of tritium with rad…

Formation and characterization of oxidic and metallic Fe/Ni multilayers prepared from Langmuir-Blodgett films

1994

Oxidic and metallic iron, nickel, and mixed iron/nickel mono- and multilayers were prepared by some treatments of iron- and nickel-containing Langmuir-Blodgett films. The layers were characterized by several surface-sensitive methods. Interactions between the iron and the nickel could be observed. The results are different to those obtained from disordered bulk alloys and from simple diffusion calculations.

Search for Neutrons as Evidence of Cold Fusion

1992

In this paper investigations performed at the University of Palermo in an attempt to reproduce the cold fusion experiment are reported. The search was devoted to detecting neutron emission from palladium electrodes electrolytically charged with deuterium. In no test was neutron emission significantly over the background observed, either in bursts or continuous. Results of a few tests are reported. For the more sensitive test, an upper limit for D(d,n) cold fusion (at 98% confidence level) of {lambda}{sub f} {lt} 3.6 {times} 10{sup {minus}24} fusion/s {center dot} d-d pair is determined.

Water Fluxes in Polymeric Membranes for Desalination via Membrane Distillation

2010

Membrane distillation is an emerging technique for seawater desalination. Hydrophobic polymeric membranes are used to separate the solute‐free water vapour from the hot solution. Vapour fluxes of commercial polymeric membranes were measured in various conditions, i.e. natural and forced convection and vacuum. Vapour fluxes were also predicted with models and compared with experimentals. Higher fluxes were recorded in vacuum conditions.