Search results for "hardening"
showing 10 items of 133 documents
Stress-Strain Law for Confined Concrete with Hardening or Softening Behavior
2013
This paper provides a new general stress-strain law for concrete confined by steel, fiber reinforced polymer (FRP), or fiber reinforced cementitious matrix (FRCM), obtained by a suitable modification of the well-known Sargin’s curve for steel confined concrete. The proposed law is able to reproduce stress-strain curve of any shape, having both hardening or softening behavior, by using a single closed-form simple algebraic expression with constant coefficients. The coefficients are defined on the basis of the stress and the tangent modulus of the confined concrete in three characteristic points of the curve, thus being related to physical meaningful parameters. It will be shown that if the v…
<title>Formation of dislocations and hardening of LiF crystals irradiated with energetic Au, Bi, Pb, and S ions</title>
2003
The irradiation of LiF crystals with Au, Pb, Bi, and S ions in the range of 400 - 2200 MeV leads to a remarkable increase of the hardness. The effect appears for Bi and Pb ions at fluences above 109 ions/cm2 and for S ions above 1010 ions/cm2. The increase of hardness follows the energy loss and is related to the formation of defects along the ion path. Defect complexes, clusters and aggregates with nanoscale dimensions serve as strong obstacles for dislocations and cause dispersion strengthening. Structural investigations reveal the generation of long-range stress in the adjacent non-irradiated part of the crystal. Close to the implantation zone, the stress exceeds the yield strength, caus…
Hardening and formation of dislocation structures in LiF crystals irradiated with MeV–GeV ions
2002
Abstract Material modifications of LiF crystals irradiated with Au, Pb and Bi ions of MeV to GeV energy are studied by means of microindentation measurements and dislocation etching. Above a critical irradiation fluence of 10 9 ions/cm 2 , the microhardness can improve by a factor of 2 in the bulk and by more than 3 on the surface. Radiation-induced hardening follows the evolution of the energy loss along the ion path. Annealing experiments indicate that complex defect aggregates created in the tracks play a major role for the hardness change. Evidence for severe structural modifications is found when etching indentation impressions in highly irradiated crystals leading to similar pattern a…
Modification of LiF structure by irradiation with swift heavy ions under oblique incidence
2013
The structural modifications of LiF irradiated with swift heavy ions under oblique angles have been investigated using AFM, SEM, chemical etching, nanoindentation and optical absorption spectroscopy. LiF crystals were irradiated under incidence angles of 30 and 70 degrees with 2.2 GeV Au (fluence 57?l011 ions-cm2) and 150 MeV Kr ions (fluence 1012?1014 ions?cm?2). Structural study on sample cross-sections shows that two damage regions ? (1) nanostructured zone and (2) dislocation ? rich zone, which are typical for irradiations at normal incidence, appear also in samples irradiated under oblique angles. However in the latter case a more complex structure is formed that leads to stronger ion-…
Hardening in LiF induced by fast Ni ions and recovery of properties under annealing
2005
The recovery of hardness and optical absorbance of LiF crystals irradiated with 640 MeV nickel ions under annealing at 450–810 K is investigated. Recovery of the hardness of irradiated crystals is initiated at temperatures above 530 K, at which a transition from a complex absorption spectrum to a spectrum with only one broad peak at 275 nm is observed. Activation energy of 0.13 eV ± 0.02 eV, which is close to that necessary for migration of H centers, is obtained from the annealing data. (© 2005 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)
PHOTOINDUCED HARDENING AND REDUCTION OF DISLOCATION MOBILITY IN C60SINGLE CRYSTALS: THE WAVELENGTH DEPENDENCE
2002
An increase of the microhardness and decrease of the dislocation mobility in C60 single crystals after light-irradiation in the wavelength range of 150–900nm in air has been observed giving evidence for photo-induced change in bonding. Efficiency of C60 phototransformation was found to increase with decreasing the wavelength.
Variational methods for the steady state response of elastic–plastic solids subjected to cyclic loads
2003
Abstract Solids (or structures) of elastic–plastic internal variable material models and subjected to cyclic loads are considered. A minimum net resistant power theorem, direct consequence of the classical maximum intrinsic dissipation theorem of plasticity theory, is envisioned which describes the material behavior by determining the plastic flow mechanism (if any) corresponding to a given stress/hardening state. A maximum principle is provided which characterizes the optimal initial stress/hardening state of a cyclically loaded structure as the one such that the plastic strain and kinematic internal variable increments produced over a cycle are kinematically admissible. A steady cycle min…
Damage and plasticity at the interfaces in composite materials and structures
2009
Abstract The structural behavior at the interface between two surfaces of ductile, brittle or quasi-brittle materials is studied by a new analytical elastoplastic damaging model. The model is developed in the framework of a thermodynamically consistent theory. The Helmholtz free energy is written to predict the materials’ hardening or softening. An isotropic damage is considered and the possible effects of dilatancy are taken into account including non-associative flow rules. The interface laws are presented both in a rate and a discrete incremental form. The analytical formulation is then implemented into a finite element code and two structural members are studied to validate the model. T…
Method for Manufacturing Custom-Shaped Prosthetic Parts from Titanium Alloys by Incremental Forming Using Industrial Robots
2014
The last decade has shown an increasing interest in a new class of forming processes known as Incremental Sheet forming (ISF). A possible application for this new procedure, targeted by the authors of this paper, is the manufacturing of custom-shaped prosthetic parts for use in various areas of human medicine. Such prostheses can have a functional role, when they target the replacing of a functional component of the human body, or an esthetic role, when they target the solving of problems related to the appearance of the human body. In this paper the authors aim to determine the strain hardening curves for the titanium alloy Ti6Al4V at room temperature and at 800°C. The incremental forming …
Residual Stresses due to High Temperature Annealing. Mathematical Model and Calculations
2006
The mathematical model is developed for description of thermomechanical processes at cooling during high temperature annealing with the known initial temperature distribution (the temperature of holding) and stresses (acquired stresses at the final of a holding). It is taken into account the thermal sensitivity and material hardening at elasto-plastic solid deforming. The methodology based on the finite element method is proposed for solving thermomechanics problems of wide range. The suitable software is developed. At the final stage of annealing a cylindrical solid it is investigated residual stresses being formed on the cooling stage.