Search results for "hardening"
showing 10 items of 133 documents
KNOWN RESIDUAL STRESS SPECIMENS USING OPPOSED INDENTATION
2009
In order to test new theories for residual stress measurement or to test the effects of residual stress on fatigue, fracture, and stress corrosion cracking, a known stress test specimen was designed and then fabricated, modeled, and experimentally validated. To provide a unique biaxial stress state, a 60 mm diameter 10 mm thick disk of 316L stainless steel was plastically compressed through the thickness with an opposing 15 mm diameter hard steel indenters in the center of the disk. For validation, the stresses in the specimen were first mapped using time-of-flight neutron diffraction and Rietveld full pattern analysis. Next, the hoop stresses were mapped on a cross section of two disks usi…
Investigation of thick sheet AHSS springback in combined bending under tension
2012
In this paper, we investigate the springback behavior of several advanced high-strength sheet steels (TRIP, Dual-Phase, ferrite-bainite) with thicknesses up to 4 mm. Samples were tested by means of the bending-under-tension (BUT) test. The BUT has been extensively applied, in the literature, to relatively thin (1 mm and thinner) sheet metals for automotive applications; the applicability of several guidelines from the literature was investigated in this work in the context of thick advanced high strength steel (AHSS) sheets and using a sample width of 12 mm. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for …
Numerical and experimental analysis of load capacity of pressure vessels for large deformations
1991
Abstract A method of theoretical and experimental investigations of large deformations and load capacity of pressure vessels has been proposed. Algorithms and programs for numerical analysis (with the finite element method) of spatial stress and strain state and load capacity have been worked out according to the Prandtl-Reuss theory of plastic flow. Loading in the vessel was realized in an incremental way. The loading process was continued up to the moment when the maximum loading was obtained (i.e. the moment when state of equilibrium of the vessel was not possible). It has been found that in thin-walled circular vessels with rigid bottoms, when a ratio of length to their diameter is less…
Memory irradiation measurements for the European SMART-1 spacecraft
2005
Three different types of memory circuits, that are intended to be used on board of the European satellite SMART-1, have been radiation hardness tested according to ESA's specification. Since the satellite is equipped with an electric propulsion engine, the spacecraft will be exposed to radiation during a long time when passing the radiation belt of the Earth. A standard DRAM circuit from SAMSUNG will serve as building block of the mass memory of SMART-1, and has been tested for total dose and proton induced single event upset (SEU). The DRAM memory showed surprisingly good resistance against radiation. The proton SEU cross sections for the radiation tolerant SRAM and FIFO circuits have also…
Optimum design for work-hardening adaptation
1977
Abstract The finite element-linear programming approach and the work-hardening adaptation criterion are used to formulate a general theory of optimum design of rigid-work-hardening structures subjected to loads which vary statically within given limits. Self-weight, as well as some technological constraints, can be introduced into the framework of the optimization problem. The optimality conditions are discussed with the aid of geometrical descriptions as well, and a comparison is made with the standard limit design. Numerical applications are given for a plane truss and a plane frame with axial force-bending moment interaction.
Compact instrumentation for radiation tolerance test of flash memories in space environment
2010
Aim of this work is the description of a test equipment, designed to be integrated on board of a microsatellite, able to investigate the radiation tolerance of non-volatile memory arrays in a real flight experiment. An FPGA-based design was adopted to preserve a high flexibility degree. Besides standard Program/Read/Erase functions, additional features such as failure data screening and latch-up protection have been implemented. The instrument development phase generated, as a by-product, a non-rad-hard version of the instrument that allowed performing in-situ experiments using 60Co and 10 MeV Boron irradiation facilities on Ground. Preliminary measurement results are reported to show the i…
Theoretical approaches for modelling buckling effects in rebars of RC members
2017
Buckling of longitudinal bars in reinforced concrete (RC) members is definitely a critical issue in framed structures subjected to seismic loads. Second order effects can affect the compressive stressâstrain law of steel bars, influencing ductility calculations of RC structures. Moreover, literature studies show that buckling can occur over a length wider than stirrupsâ pitch (global buckling mode), involving more stirrups and inducing large deflections in the bar. If the critical length is not carefully estimated, stirrupsâ failure can occur, causing also the sudden loss of confining effects in concrete. This paper presents the results of different approaches for calculating the crit…
Concrete columns confined with fibre reinforced cementitious mortars: Experimentation and modelling
2014
Abstract The structural behaviour of concrete columns strengthened with a system made up of fibre nets embedded in an inorganic stabilized cementitious matrix under an uniaxial load was investigated. Medium size specimens with circular and square cross-section were cast and subjected to monotonic uniaxial compression, to investigate the efficiency of a p-Phenylene BenzobisOxazole (PBO) Fibre Reinforced Cementitious Mortar (FRCM) system in increasing both strength and ductility. The experimental results show that the confinement system adopted produced a noticeable increment in strength and ductility, though the low mechanical ratios of fibre considered were not always able to ensure hardeni…
Cold tolerance and cold-induced modulation of gene expression in two Drosophila virilis group species with different distributions
2011
Abstract The importance of high and low temperature tolerance in adaptation to changing environmental conditions has evoked new interest in modulations in gene expression and metabolism linked with stress tolerance. We investigated the effects of rapid cold hardening and cold acclimatization on the chill coma recovery times of two Drosophila virilis group species, Drosophila montana and D. virilis, with different distributions and utilized a candidate gene approach to trace changes in their gene expression during and after the cold treatments. The study showed that cold acclimatization clearly decreases chill coma recovery times in both species, whereas rapid cold hardening did not have a s…
Fatigue crack propagation from a cold-worked hole
2007
Abstract The cold expansion process is widely used to enhance the fatigue life of structures with fastener holes. Various studies assert that the cold expansion improves the fatigue strength of fastener holes; however, the improvement of fatigue life is difficult to quantify. Therefore, the influence on fatigue life of cold-worked process was studied by numerical and experimental tests. Then, a parametric study on material hardening behavior and Bauschinger’s parameter was performed for several loading conditions in order to determine their effect on crack growth propagation. The results of the numerical tests have exhibited a good prediction of the fatigue life of the component.