Search results for "heat flux"
showing 10 items of 133 documents
The inclination effect on the performance of water-filled heat pipes
1991
Abstract Heat pipes have been used in wide ranges of applications today including solar engineering. During this research study, the inclination dependent performance of water filled heat pipes was investigated both theoretically and experimentally for solar energy applications. The results showed that the performance of water-filled heat pipes are strongly dependent on the inclination and the heat source temperatures. As a general result, the heat transfer capability of water filled heat pipes is reduced dramatically below a 45° tilt angle.
3D modeling of doping from the atmosphere in floating zone silicon crystal growth
2017
Abstract Three-dimensional numerical simulations of the inert gas flow, melt flow and dopant transport in both phases are carried out for silicon single crystal growth using the floating zone method. The mathematical model allows to predict the cooling heat flux density at silicon surfaces and realistically describes the dopant transport in case of doping from the atmosphere. A very good agreement with experiment is obtained for the radial resistivity variation profiles by taking into account the temperature dependence of chemical reaction processes at the free surface.
Peltier cells as temperature control elements: Experimental characterization and modeling
2014
Abstract The use of Peltier cells to realize compact and precise temperature controlled devices is under continuous extension in recent years. In order to support the design of temperature control systems, a simplified modeling of heat transfer dynamics for thermoelectric devices is presented. By following a macroscopic approach, the heat flux removed at the cold side of Peltier cell can be expressed as Q ˙ c = γ ( T c − T c eq ) , where γ is a coefficient dependent on the electric current, Tc and T c eq are the actual and steady state cold side temperature, respectively. On the other hand, a microscopic modeling approach was pursued via finite element analysis software packages. To validat…
Improvement of building wall surface temperature measurements by infrared thermography
2005
By using quantitative thermal scanning of building surface structures, it is possible to access the temperature field. For further calculation of the heat flux exchanged by these structures with the environment, one must quantify as finely as possible the temperature field on the bodies surfaces. For this purpose we have to take into account that real bodies are not black, which implies that a part of the ambient radiation received by the infrared camera detectors is reflected radiation. In this paper, we present a method to quantify the reflected flux by using an infrared mirror, which allows large surface temperature measurements by infrared thermography under near-ambient conditions with…
An Investigation of the Thermal Effects in Orthogonal Cutting Associated with Multilayer Coatings
2001
Abstract This paper deals with an experimental and analytical investigation into the tool-chip interface behaviour, influencing the temperature and heat transfer at the multilayered coated-tool rake face during orthogonal cutting of carbon and stainless steels. New methodology for assessing the amount of thermal energy generated when machining with a coated tool insert with natural and restricted contact coupled with a metallic chip, using thermophysical properties of the sliding materials is developed in this study. It was proven, based on the heat flux analysis, that the use of advanced coatings with an intermediate Al 2 O 3 layer can substantially improve the heat flow into the chip at d…
A non-local model of fractional heat conduction in rigid bodies
2011
In recent years several applications of fractional differential calculus have been proposed in physics, chemistry as well as in engineering fields. Fractional order integrals and derivatives extend the well-known definitions of integer-order primitives and derivatives of the ordinary differential calculus to real-order operators. Engineering applications of fractional operators spread from viscoelastic models, stochastic dynamics as well as with thermoelasticity. In this latter field one of the main actractives of fractional operators is their capability to interpolate between the heat flux and its time-rate of change, that is related to the well-known second sound effect. In other recent s…
A critical analysis of three remote sensing-based actual evapotranspiration assessment methods over sparse crops agricultural areas
2010
During last two decades the increasing availability of remotely sensed acquisitions in the thermal infrared part of the spectrum has encouraged hydrologist community to develop models and methodologies based on these kind of data. The aim of this paper is to compare three methods developed to assess the actual evapotranspiration spatial distribution by means of remote sensing data. The comparison was focused on the differences between the "single" (SEBAL) and "two" source (TSEB) surface energy balance approaches and the S-SEBI semi-empirical method. The first assumes a semiempirical internal calibration for the sensible heat flux assessment; the second uses a physically based approach in or…
On the numerical assessment of the thermal-hydraulic operating map of the DEMO Divertor Plasma Facing Components cooling circuit
2020
Abstract Within the framework of the Work Package DIV 1 - “Divertor Cassette Design and Integration” of the EUROfusion action, a research campaign has been jointly carried out by University of Palermo and ENEA to investigate the thermal-hydraulic behaviour of the DEMO divertor cassette cooling system, focussing the attention on the 2018 configuration of the Plasma Facing Components (PFCs) circuit consistent with the DEMO baseline 2017. The research campaign has been carried out following a theoretical-computational approach based on the finite volume method and adopting the commercial Computational Fluid-Dynamic (CFD) code ANSYS CFX. A steady-state CFD analysis has been carried out for the …
On the thermal-hydraulic optimization of DEMO divertor plasma facing components cooling circuit
2018
Abstract Within the framework of the Work Package Divertor, Subproject: Cassette Design and Integration (WPDIV-Cassette) of the EUROfusion action, a research campaign has been jointly carried out by ENEA and University of Palermo to investigate the thermal-hydraulic performances of the DEMO divertor cassette cooling system. Attention has been focussed on the divertor Plasma Facing Components (PFCs) cooling circuit and a parametric analysis has been carried out in order to assess the potential impact of proper layout changes on its thermal-hydraulic performances, mainly in terms of coolant total pressure drop, flow velocity distribution and margin against critical heat flux occurrence. The r…
Hydraulic assessment of an upgraded pipework arrangement for the DEMO divertor plasma facing components cooling circuit
2021
Abstract In the context of the Work Package DIVertor (WPDIV) of the EUROfusion action, a research campaign has been carried out by University of Palermo in cooperation with ENEA to assess the thermal-hydraulic performances of the DEMO divertor cooling system, concentrating the attention on its 2019 Plasma Facing Components (PFCs) configuration, relevant to DEMO baseline 2017. The research activity has been performed following a theoretical-numerical technique based on the finite volume method and adopting the well-known ANSYS CFX CFD code. The PFCs cooling circuit thermal-hydraulic performances under nominal steady-state conditions, assessed mainly in terms of coolant total pressure drop, c…