Search results for "him"
showing 10 items of 8346 documents
Co-culture of rat brain cells as a tool for studying cell-cell interactions
2012
Brain capillary endothelial cells (BCECs) form the blood-brain barrier (BBB) in response to interaction with other brain cells (astrocytes, pericytes and neurons). BCECs are characterized by tight junctions (TJ), maturation and stabilization of which require different proteins, such as occludin. When co-cultured with astrocytes and neurons, BCECs were found to form a monolayer resembling the natural BBB: paracellular flux of dopamine and sucrose (i.e. compounds which are unable to cross the BBB in vivo) significantly decreased (1), while the transendothelial electrical resistance (TEER) increased. In these conditions, BCECs produced a larger amount of occludin and tended to localize it at t…
Nanostructured Material Fabrication for Energy Conversion
2010
Structural distortions in homoleptic (RE)4A (E = O, S, Se; A = C, Si, Ge, Sn): Implications for the CVD of tin sulfides
2001
The structures of Sn(SBut)4 and Sn(SCy)4 have been determined and adopt S4 and D2 conformations respectively; the anion [(PhS)Sn3]−, as its Ph4P+ salt, has a structure approaching Cs symmetry. In all three compounds, there are large variations in the ∠S–Sn–S within the same molecule, which have been rationalised in terms of the C–S–Sn–S–C conformations. For Sn(SR)4, the ∠S–Sn–S increases as the conformations change from trans, trans to trans, gauche and gauche, gauche, as the number of eclipsed lone pairs decreases and this rationale is shown to be applicable to a variety of A(ER)4 (A = C, Si, Ge, Sn; E = O, S, Se) and related [Mo(SR)4, Ga(SR)4−] systems. AM1 calculations have been used to …
Deposition of tin sulfide thin films from tin(iv) thiolate precursors
2001
AACVD (aerosol-assisted chemical vapour deposition) using (PhS)(4)Sn as precursor leads to the deposition of Sn3O4 in the absence of H2S and tin sulfides when H2S is used as co-reactant. At 450 degreesC the film deposited consists of mainly SnS2 while at 500 degreesC SnS is the dominant component. The mechanism of decomposition of (PhS)(4)Sn is discussed and the structure of the precursor presented.
Study of morphology, mechanical properties and thermal degradation of titania-polycarbonate nanocomposites as function of crystalline phase and amount
2013
Titania nanoparticles were prepared using a sol–gel method and calcination at 2008C and 6008C to obtain anatase and rutile phases, respectively. The obtained powders were used to prepare polycarbonate (PC)-titania nanocomposites by melt compounding. The effect of different crystalline phases and amounts of titania, in the range 1–5 wt%, on the morphology, mechanical properties, and thermal degradation kinetics of PC was investigated. The results show that the filler modified the plasticity or rigidity of the polymer and influenced the degradation kinetics, in different ways depending on the type and amount of titania.
Photocatalytic partial oxidation of propylene in the presence of mesoporous organosilane-modified titanias
2014
Titania-Silica Mesoporosa per l’ossidazione Parziale Fotocatalitica di Propilene in Regime Gas-Solido
2013
New Insights into Segmental Packing, Chain Dynamics and Thermomechanical Performance of Aliphatic Polyurea Composites: Comparison between Silica Oxid…
2021
Polyurea (PU) is intrinsically reinforced by its microphase-separated morphology, giving its excellent mechanical properties. In this study, it is shown how a high-index PU formulation applies easy diffusion of hard segments into the soft phase of the PU matrix and tune its chain mobility. Moreover, the interaction of micro (>100 nm), nano (<100 nm) fillers with the microdomains and their thermomechanical properties are unraveled. Herein, nanosilica oxide (NS) and micro titanium (III) oxide (Ti2O3) are incorporated at low loadings into a solvent-free two-component aliphatic PU via insitu polymerization. While NS achieves an interfacial interaction with urea groups and forms a tight ha…