Search results for "lcsh:TK1-9971"
showing 10 items of 157 documents
Flexible Spare Core Placement in Torus Topology based NoCs and its validation on an FPGA
2021
In the nano-scale era, Network-on-Chip (NoC) interconnection paradigm has gained importance to abide by the communication challenges in Chip Multi-Processors (CMPs). With increased integration density on CMPs, NoC components namely cores, routers, and links are susceptible to failures. Therefore, to improve system reliability, there is a need for efficient fault-tolerant techniques that mitigate permanent faults in NoC based CMPs. There exists several fault-tolerant techniques that address the permanent faults in application cores while placing the spare cores onto NoC topologies. However, these techniques are limited to Mesh topology based NoCs. There are few approaches that have realized …
Effects of ions-releasing restorative materials on the dentine bonding longevity of modern universal adhesives after load-cycle and prolonged artific…
2019
This study aimed at evaluating the microtensile bond strength (MTBS) and fractographic features of dentine-bonded specimens created using universal adhesives applied in etch-and-rinse (ER) or self-etching (SE) mode in combination with modern ion-releasing resin-modified glass-ionomer cement (RMGIC)-based materials after load cycling and artificial saliva aging. Two universal adhesives (FTB: Futurabond M+, VOCO, Germany
5G Functional Architecture and Signaling Enhancements to Support Path Management for eV2X
2019
Enhanced vehicle-to-everything (eV2X) communication is one of the most challenging use cases that the fifth generation (5G) of cellular mobile communications must address. In particular, eV2X includes some 5G vehicular applications targeting fully autonomous driving which require ultra-high reliability. The usual approach to providing vehicular communication based on single-connectivity transmission, for instance, through the direct link between vehicles (PC5 interface), often fails at guaranteeing the required reliability. To solve such a problem, in this paper, we consider a scheme where the radio path followed by eV2X messages can be proactively and dynamically configured to either trans…
Automatic Segmentation Using a Hybrid Dense Network Integrated With an 3D-Atrous Spatial Pyramid Pooling Module for Computed Tomography (CT) Imaging
2020
Computed tomography (CT) with a contrast-enhanced imaging technique is extensively proposed for the assessment and segmentation of multiple organs, especially organs at risk. It is an important factor involved in the decision making in clinical applications. Automatic segmentation and extraction of abdominal organs, such as thoracic organs at risk, from CT images are challenging tasks due to the low contrast of pixel values surrounding other organs. Various deep learning models based on 2D and 3D convolutional neural networks have been proposed for the segmentation of medical images because of their automatic feature extraction capability based on large labeled datasets. In this paper, we p…
Evaluation of a Cell-Free Collagen Type I-Based Scaffold for Articular Cartilage Regeneration in an Orthotopic Rat Model.
2020
The management of chondral defects represents a big challenge because of the limited self-healing capacity of cartilage. Many approaches in this field obtained partial satisfactory results. Cartilage tissue engineering, combining innovative scaffolds and stem cells from different sources, emerges as a promising strategy for cartilage regeneration. The aim of this study was to evaluate the capability of a cell-free collagen I-based scaffold to promote cartilaginous repair after orthotopic implantation in vivo. Articular cartilage lesions (ACL) were created at the femoropatellar groove in rat knees and cell free collagen I-based scaffolds (S) were then implanted into right knee defect for the…
Design and control of an innovative electronic load for the photovoltaic module characterization
2016
The paper proposes a new electronic load setup for a fast, low-cost and standard-compliant characterization of a photovoltaic module. The approach is based on the use of a DC-DC converter, exploiting its ability to emulate a resistor. In particular, a Buck-Boost converter topology is employed. The model is implemented in the Simulink/SimPower System environment. A commercial PV Conergy E215P photovoltaic module is used in order to evaluate the performances of the proposed electronic load and to validate the proposed approach.
Cloaking In-Plane Elastic Waves with Swiss Rolls
2020
We propose a design of cylindrical cloak for coupled in-plane shear waves consisting of concentric layers of sub-wavelength resonant stress-free inclusions shaped as Swiss rolls. The scaling factor between inclusions&rsquo
A Spatial-Temporal Correlation Approach for Data Reduction in Cluster-Based Sensor Networks
2019
International audience; In a resource-constrained Wireless Sensor Networks (WSNs), the optimization of the sampling and the transmission rates of each individual node is a crucial issue. A high volume of redundant data transmitted through the network will result in collisions, data loss, and energy dissipation. This paper proposes a novel data reduction scheme, that exploits the spatial-temporal correlation among sensor data in order to determine the optimal sampling strategy for the deployed sensor nodes. This strategy reduces the overall sampling/transmission rates while preserving the quality of the data. Moreover, a back-end reconstruction algorithm is deployed on the workstation (Sink)…
Polymer-Functionalised Nanograins of Mg-Doped Amorphous Calcium Carbonate via a Flow-Chemistry Approach
2019
Calcareous biominerals typically feature a hybrid nanogranular structure consisting of calcium carbonate nanograins coated with organic matrices. This nanogranular organisation has a beneficial effect on the functionality of these bioceramics. In this feasibility study, we successfully employed a flow-chemistry approach to precipitate Mg-doped amorphous calcium carbonate particles functionalized by negatively charged polyelectrolytes&mdash
Human-Robot Cooperation for Surface Repair Combining Automatic and Manual Modes
2020
[EN] This article develops a human-robot cooperation to carry out treatments such as sanding, polishing, etc. on the surface of a known rigid object. For this purpose, a vision system is considered to get the object location to ensure not only the perpendicularity of the obot tool to the object surface but also a smooth approach of the tool to the surface. In order to add flexibility, the proposal includes the simultaneous combination of automatic and manual modes of operation. Thus, the human user can guide the robot tool to treat arbitrary areas (manual mode) and, when the operator releases the tool, the robot goes into the automatic mode to treat prior established areas. The method uses …