Search results for "leaning"

One-step electrodeposition of superhydrophobic coating on 316L stainless steel

2021

Superhydrophobic coatings were fabricated through a one-step electrochemical process onto the surface of 316L stainless steel samples. The presence of hierarchical structures at micro/nanoscale and manganese stearate into the coatings gave superhydrophobicity to the coating, with contact angle of ~160°, and self-cleaning ability. Corrosion resistance of 316L samples was also assessed also after the electrodeposition process through Electrochemical Impedance Spectra recorded in an aqueous solution mimicking seawater condition.

Effectiveness of some protective and self-cleaning treatments: a challenge for the conservation of temple G stone in Selinunte

2021

Abstract The Temple G of the Archaeological Park of Selinunte (Italy), the largest in Europe, is one of the most impressive temples in the Magna Grecia. Today, it is completely destroyed due to a strong earthquake occurred in the Middle Ages. The used stone is a calcarenite coming from the ancient and renowned quarries of Cusa near the acropolis. This work comes from the today’s proposal of Temple G anastylosis. The goal of the work is to provide the results relating the protective effectiveness of three polymer formulations, appropriately selected, on stone samples taken from the “Capitello” quarry, part of “Cusa quarries”. The formulations functionality was deployed by adding TiO2 nanopar…

A Brief Review on the Resistance-in-Series Model in Membrane Bioreactors (MBRs)

2019

The cake layer deposited on the membrane modules of membrane bioreactors (MBRs), especially under a submerged configuration, represents a relevant and fundamental mechanism deeply influencing the development of membrane fouling. It negatively affects the total resistance to filtration, while exerting a positive effect as a “pre-filter„ promoting the “dynamic membrane„ that protects the physical membrane from internal fouling. These two opposite phenomena should be properly managed, where the submerged membranes are usually subjected to a periodical cake layer removal through ordinary (permeate backwashing and air scouring) and/or irregular cleaning actions (manual ph…

Correction to Overview and Essentials of Biomass Gasification Technologies and Their Catalytic Cleaning Methods

2017

Double Step Electrochemical Process for the Deposition of Superhydrophobic Coatings for Enhanced Corrosion Resistance

2021

Superhydrophobic surface on anodized AA5083 sample was obtained by an electrochemical process. Scanning Electron Microscopy and Fourier Transform Infrared Spectroscopy analyses revealed the hierarchical structure of the coating and the presence of manganese stearate. These features were crucial for the coating superhydrophobicity, demonstrated by a measured contact angle of ~ 163° and its self-cleaning ability. Electrochemical characterization in an aqueous solution mimicking seawater proved an enhanced corrosion resistance due to the superhydrophobic coating with respect to anodized AA5083 sample that also lasted after 20 immersion days in Cl- containing electrolyte.

Influence of sol counter-ions on the visible light induced photocatalytic behaviour of TiO2 nanoparticles

2014

Titanium dioxide (TiO2) nanoparticles are attracting increasing interest because of their superior photocatalytic and antibacterial properties. Here, aqueous titanium oxy-hydroxide sols were made, using a green synthesis method, from the controlled hydrolysis/peptisation of titanium isopropoxide. Three different mineral acids were used to peptise the sol (HNO3, HBr and HCl), and provide counter-ions. The influence of nitrate or halide sol counter-ions on size distributions of the starting sols were measured via photon correlation spectroscopy (PCS). Semi-quantitative phase composition analysis (QPA), on the gels thermally treated at 450 and 600 degrees C, was carried out via Rietveld refine…

XPS and SIMS study of aluminium native oxide modifications induced by Q-switched Nd:YAG laser treatment

2006

Publié suite au congrès ECASIA: 11th European Conference on Applications of Surface and Interface Analysis, 25-30 September 2005, Vienna, Austria; International audience; During laser cleaning of aluminium in ambient atmosphere, modifications of the metal surface can be induced by transient thermal effects. This work aims to characterize the modification of the aluminium oxide layer on pure aluminium for a wide range of power per area using a Q-switched Nd :YAG (1064 nm) laser with two pulse durations, 10 and 180 ns. Experiments were carried out with single laser shots in ambient air at fluences (e.g. energy per area) below the ablation regime. For 10-ns pulses with fluences between 0.7 and…

Corrosion of stainless steel in food and pharmaceutical industry

2021

Abstract Stainless steels are widely used in the food and pharmaceutical industry because of their high corrosion resistance and superior mechanical properties. These features are crucial because produced foodstuffs and drugs must comply with high purity and quality standards. Just a proper selection of stainless steel grade can prevent corrosion phenomena that can be detrimental to the whole manufacturing process. Food/drugs production process phases will be here analyzed and discussed with a particular emphasis on the possible corrosion mechanism of stainless steels in those particular operating conditions. Recent advances on the methods to assess corrosion of stainless steels in food and…

MODERN TECHNOLOGIES FOR CONSERVATION OF VILLA ZITO PAINTINGS COLLECTION (PALERMO – SICILY)

2017

In this study we describe the conservative integrated approach performed on 40 paintings, dating from different period (XVII- XX century), belonging to “Fondazione Sicilia “ and exposed in Villa Zito paint gallery in Palermo (Mazzocca 2015). Through a multidisciplinary approach both constitutive materials and state of conservation have been determined. Particularly, pigments and executive techniques were identified by non-invasive diagnostic investigation (XRF analysis, UV fluorescence acquisition, and IR Reflectography) as well as previous restorations events. The study has included the revealing of microbial colonization by using non-invasive sampling methods (Nylon membrane fragment) and…

Waterless Cleaning Compositions with Disinfection Properties: Efficacy and Environmental Aspects / Bezûdens Tîrîðanas Lîdzekïi Ar Dezinficçjoðo Iedar…

2015

Abstract The microbial ecology of different indoor environments determines the human microbiome. Hence, cleaning and disinfection of indoor environments like hospitals, apartments, automobiles, etc. are of great importance. Nonaqueous surface cleaning preparations (SCPs) are often used for this purpose. A cleaning composition may contain the following compounds: primary surfactant, cosurfactant, solvent, cosolvent, organotropic (organic solubilizing) agent, hydrotropic (water solubilising) agent, water and salts, and special additives. In this paper, the efficacy of complex preparations is discussed, focusing on the chemical composition and testing methods. Particular attention is paid to q…