Search results for "limiter"

Booton's problem re-examined

1998

The application of the stochastic linearization technique to the specific problem analyzed by Booton is reexamined. It is shown that Booton has made a subtle error in the procedure for minimization of the mean square force difference between the sharp limiter and its linear equivalent counterpart

A fiber-based limiter at 170 Gbit/s for all-optical regeneration

2009

We report the numerical and experimental studies of a spectrally filtered fiber-based optical limiter at 170 Gbit/s. The device, including less than 1 km-long of highly nonlinear optical fiber and a 3 nm-width filter, exhibits good performance at an average input power of 14.5 dBm. No power penalty has been observed and a strong robustness against optical noise has been demonstrated.

Thermal Parametric and Thermo-Mechanical analyses for the Limiter Blanket Module of ITER

1996

Scaling guidelines of a soliton-based power limiter for 2R-optical regeneration applications

2010

International audience; In this work, we report scaling rules for the design of an all-fibered soliton-based power limiter for reamplification and reshaping (2R) regeneration process. In particular, we propose general guidelines to fix the optimum fiber length and initial power of the regenerator. We quantitatively point out the optical power limiting effect of the device enabling a significant reduction of the amplitude jitter of a degraded signal. Influence of the initial level of amplitude jitter is discussed and the results are compared with a self-phase modulation-based configuration working in the normal dispersion regime. Realistic numerical simulations in the context of 160 Gbit/s s…

Nuclear Analysis of an ITER Blanket Module

2013

ITER blanket system is the reactor’s plasma-facing component, it is mainly devoted to provide the thermal and nuclear shielding of the Vacuum Vessel and external ITER components, being intended also to act as plasma limiter. It consists of 440 individual modules which are located in the inboard, upper and outboard regions of the reactor. In this paper attention has been focused on to a single outboard blanket module located in the equatorial zone, whose nuclear response under irradiation has been investigated following a numerical approach based on the Monte Carlo method and adopting the MCNP5 code. The main features of this blanket module nuclear behaviour have been determined, paying part…

Measuring the isotope effect on the gross beryllium erosion in JET

2022

Abstract The isotope effect, hydrogen (H) versus deuterium (D), on the gross beryllium (Be) erosion yield has been measured in ohmic limiter plasmas in JET tokamak by spectroscopic means. A simplified method to extract the effective sputtering yield from the quotient of the radiances of the D α or D γ and the Be II lines at 527 nm was applied. A clear isotope effect has been found, the erosion yield of D being about a factor of 2 larger compared to H in the whole explored plasma density range. This is in agreement with physical sputtering data obtained with H+ and D+ ion beams and also with material surface computer simulations. The already published contribution of chemically assisted phys…

Thermal solitons along wires with flux-limited lateral exchange

2021

We obtain some exact solutions in the context of solitons, for heat conduction with inertia along a cylinder whose heat exchange with the environment is a non-linear function of the difference of temperatures of the cylinder and the environment, due to a flux-limiter behavior of the exchange. We study the consequences of heat transfer and information transfer along the wire, and we compare the situation with analogous solitons found in nonlinear lateral radiative exchange studied in some previous papers. We also find further exact solutions in terms of Weierstrass elliptic functions for the sake of completeness.

Analysis of Torque Developed in Axial Flux, Single-Phase Brushless DC Motor With Salient-Pole Stator

2004

An analysis of the torque developed by a single-phase disc brushless permanent magnet motor with salient-pole stator is presented. The machine represents a new family of brushless disc motors with the starting torque issue appearing to be most challenging. To produce a starting torque, the permanent magnets on one of the rotor discs are distributed nonuniformly. However, this significantly distorts a shape of the cogging torque versus rotational angle characteristic which, in turn, affects a waveform of the overall torque. A three-dimensional (3-D) finite-element model is used for the purpose of determining of angular variations of the torque developed by the motor. To find how the torque v…

Overview of diagnostic performance and results for the first operation phase in Wendelstein 7-X (invited)

2016

Wendelstein 7-X, a superconducting optimized stellarator built in Greifswald/Germany, started its first plasmas with the last closed flux surface (LCFS) defined by 5 uncooled graphite limiters in December 2015. At the end of the 10 weeks long experimental campaign (OP1.1) more than 20 independent diagnostic systems were in operation, allowing detailed studies of many interesting plasma phenomena. For example, fast neutral gas manometers supported by video cameras (including one fast-frame camera with frame rates of tens of kHz) as well as visible cameras with different interference filters, with field of views covering all ten half-modules of the stellarator, discovered a MARFE-like radiati…

Analysis of metallic impurity content by means of VUV and SXR diagnostics in hybrid discharges with hot-spots on the JET-ITER-like wall poloidal limi…

2019

In preparation for the upcoming JET D-T campaign, great effort has been devoted during the 2015-2016 JET campaigns with the ITER-like wall (ILW) to the extension of the high performance H-mode phase in baseline and hybrid scenarios. Hybrid discharges were the only ones that have been stopped by the real-time vessel protection system due hot-spot formation on the outboard poloidal limiter. Generation of hot-spots was linked to the application of high neutral beams injection and ion cyclotron resonance heating (ICRH) power. In tokamaks with high-Z plasma components, the use of ICRH heating is also accompanied by an increased metallic impurity content. Simultaneous control of hot-spot temperat…