Search results for "lumi"
showing 10 items of 4067 documents
Electromagnetic and Thermal Modelling for Calculating Ageing Rate of Distribution Transformers
2018
Prediction of the lifetime for transformers is very important for maintenance and asset management. Finite element analysis was performed on a 5 MVA distribution transformers with aluminium foil-type windings and voltage rating 6600 V/23000 V. Electromagnetic modelling is implemented on the full three-phase transformer to calculate distributed losses, taking the skin effect into account. To reduce the computational burden, the distributed losses in one phase are used to analyse temperature rise in one phase of the transformer. The temperature rise results were used to determine the ageing rate of the transformer. Further, the influence of ambient temperature and cooling on the temperature r…
Structural, optical, and luminescence properties of ZnO:Ga optical scintillation ceramic
2018
This paper discusses the characteristics of ZnO and ZnO:Ga ceramics fabricated by uniaxial hot pressing. The short-wavelength transmission limit of zinc oxide ceramics is in the 370-nm region; the long-wavelength limit is determined by the free-charge-carrier concentration and lies in the interval from 5 to 9 μm. The total transmittance of such ceramics in the visible and near-IR regions is about 70% when the sample is 0.5 mm thick. The luminescence spectrum is represented by a broad emission band with maximum at 580 nm, having a defect nature. The introduction of 0.03–0.1 mass % gallium into the zinc oxide structure inhibits grain growth and increases the free-charge-carrier concentration …
New low-temperature phosphate glasses as a host for Europium Ions
2021
Abstract Artificial lightining, especially that of light emitting diodes, and telecommunications are penetrating every part of human lives daily. Different compositions phosphate glasses were suggested as a suitable host material for Eu3+ ions. Here rare earth metal ions act as luminescent centers also perturbing the bond order of phosphate glass network comprised of (PO4)3−, [−(O)PO3]2−, [−(O)2PO2]−, [−(O)3PO] structural units, which is indicated by Raman spectroscopy, confirming successful integration of aforementioned ions into the glass material. Glasses doped with Eu3+ ions show their typical photoluminescence spectra in low symmetry environment, consisting of the highest intensity 5D0…
An anomalous wave formation at the Al/Cu interface during magnetic pulse welding
2020
This paper reports an anomalous wave formation at an Al/Cu bimetallic interface produced by magnetic pulse welding. The mechanism of the anomalous wave formation is investigated using both metallurgical characterization and the interface kinematics. It reveals that the anomalous wave is formed with the combination of the intermediate zone and the interdiffusion zone with a thickness of 70 nm, wherein the intermediate zone is caused by the local melting due to the high shear instability, and the interdiffusion zone is formed below the melting point of aluminum combined with ultrahigh heating and cooling rates of about 10^13 °C s^−1. A multiphysics simulation of impact welding has been perfor…
How activator ion concentration affects spectroscopic properties on Ba4Y3F17: Er3+, Yb3+, a new perspective up-conversion material
2018
Abstract Ba4Y3F17 with Er3+ and Yb3+, a promising material for up-conversion luminescence, was synthesized. Excellent isomorphic capacity was detected. Low-temperature measurements show that erbium ions are incorporated in multiple lattice positions, which is inconsistent with the current model of Ba4Y3F17 crystal lattice structure. Activator ion concentration has a different impact on 4S3/2 and 4F9/2, states (for the green and red luminescence, respectively) depopulation. Energy transfer from Er3+ 4S3/2 state to Yb3+ is observed even at low temperature (15 K) while Er-Er cross-relaxation is observed from 120 K and above. Yb3+ concentration has a great impact to red-to-green up-conversion l…
Experimental and numerical investigation on a new FSW based metal to composite joining technique
2018
Abstract In the last decades, different techniques were proposed to join aluminum sheets with composites materials. Each of them has advantages and weak points over the others and new techniques and patents are continuously developed to overcome these difficulties. In this paper an experimental and numerical investigation on a new Friction Stir Welding based approach to mechanically join AA6082-T6 to self-reinforced polypropylene is presented. The aluminum sheet is pre-holed along both the sides of the weld line and a pinless tool generates the heat and pressure needed to prompt back-extrusion of the composite. New experimental fixtures and hole designs were investigated in order to enhance…
Evaluation of Vertical Fatigue Cracks by Means of Flying Laser Thermography
2019
The present paper proposes a new procedure to analyze the temperature field distribution during Flying Laser Spot and Laser Line Thermographic scanning (FLST, FLLT) of metallic components, in order to detect vertical surface cracks. The methodology exploits the changes in the temperature field produced by a vertical crack, acting as a barrier towards heat diffusion, when the laser approaches the defect. A number of small regions of interests (ROIs) is placed nearby and around the laser source. The average temperature from each ROI is then monitored during the laser scanning. Vertical cracks can be detected by analyzing and comparing the temperature fluctuations from each ROI when the laser …
Vapor plume and melted zone behavior during dissimilar laser welding of titanium to aluminum alloy
2020
The present study deals with continuous Yb:YAG laser welding of pure titanium to aluminum alloy A5754 performed with different beam offsets to the joint line. Spectroscopic and morphological characterization of vapor plume exiting the keyhole was combined with post-mortem observation and energy-dispersive X-ray spectroscopy (EDX) analysis of the welds. The laser beam centered on the joint line resulted in periodic transversal inclination of a vapor jet on the aluminum side associated with a local increase of melt width and an intense spatter formation. Such behavior can be attributed to the instability of the keyhole wall from the aluminum side. The beam offset on the titanium side led to …
Recent progress in understanding the persistent luminescence in SrAl 2 O 4 :Eu,Dy
2019
Ever since the discovery of SrAl2O4:Eu,Dy persistent afterglow material, that can intensively glow up to 20 h, the mechanism of long-lasting luminescence has been a popular area of research. The re...
Luminescence properties of chlorine molecules in glassy SiO 2 and optical fibre waveguides
2017
The support from Latvian Research Program IMIS 2, project “Photonics and materials for photonics” is acknowledged. K.K. was partially supported by the Collaborative Research Project of Materials and Structures Laboratory, Tokyo Institute of Technology. The publication costs of this article were covered by the Estonian Academy of Sciences and the University of Tartu.