Search results for "maximum"
showing 10 items of 753 documents
Veterinary Drugs and Growth Promoters Residues in Meat and Processed Meats
2009
Wireless Power Transfer System Design for E-bikes Application
2019
The present work presents an analysis of Inductive Coupled Power Transfer (ICPT) Systems behaviour applied to electrical bikes. In particular, the study has focused on the design of the coupled coils of this system. In the first part of the work, the theoretical aspects of the wireless power system are handled. In the second part of the work, the inductive features of the coupled windings are analyzed. In order to perform this process, the Ansys Maxwell software has been used, performing 3D simulations. To conclude, the results of the simulations are compared.
Groundwater radon measurements in the Mt. Etna area.
2003
Radon levels were measured in 119 groundwater samples collected throughout the active volcanic area of Mt. Etna by means of a portable Lucas-type scintillation chamber. The measured activity values range from 1.8 to 52.7 Bq l(-1). About 40% of the samples exceed the maximum contaminant level of 11 Bq l(-1) proposed by the USEPA in 1991. The highest radon levels are measured in the eastern sector of the volcano, which is the seismically most active zone of the volcano. On the contrary the south-western sector, which is both seismically active and a site of intense magmatic degassing, display lower radon levels. This is probably due to the formation of a free gas phase (oversaturation of CO(2…
Performance analysis of photovoltaic powered dc motor — Propeller system
2015
The application of autonomous directly photovoltaic (PV) powered electro-mechanical has received increasing attention for different applications (e.g. PV water pumping, PV powered cooling of arid climate greenhouses, solar vehicles etc). The PV array output is a nonlinear and time-dependent power supply that varies with solar intensity and cell temperature, so the performance characteristics of the directly PV-powered DC motor — propeller system are very different than when powered by a constant DC voltage. The focus of this work is to do performance analysis of directly PV-powered DC motor — propeller system. Through performance evaluation, it has been observed that power transfer matching…
Design, modeling, and simulation of a photovoltaic water pumping system
2018
Electric pumps cannot be fed in those areas where they are not connected to the electric public distribution grid. In those areas, it is useful to feed electric pumps by means of the electricity generated from renewable energy sources plants. Among these, the Solar Water Pumping Systems feed electric pump thanks to the electricity generated by a photovoltaic plant. In this paper, a whole SWPS is fully designed, modelled, and simulated in Matlab environment. The proposed implementation is an useful tool for SWPS testing.
Development of Slewing Mirror Telescope Optical System for the UFFO-pathfinder
2013
The Slewing Mirror Telescope (SMT) is the UV/optical telescope of UFFO-pathfinder. The SMT optical system is a Ritchey-Chretien (RC) telescope of 100 mm diameter pointed by means of a gimbal-mounted flat mirror in front of the telescope. The RC telescope has a 17 × 17arcmin2 in Field of View and 4.3 arcsec resolution (full width half maximum of the point spread function) The beam-steering mirror enables the SMT to access a 35 × 35degree region and point and settle within 1 sec. All mirrors were fabricated to about 0.02 wavelengths RMS in wave front error (WFE) and 84.7% average reflectivity over 200 nm ~ 650 nm. The RC telescope was aligned to 0.05 wavelengths RMS in WFE (test wavelength 63…
Wireless power transfer system stability analysis for E-bikes application
2019
The present work reports the stability analysis of an Inductive Coupled Power Transfer (ICPT) System coupled to an electrical bike. The study has focused on two coupled coils with circular geometry and vertical disposition. In the first part of the work, the theoretical aspects related to the stability of wireless power systems are handled. In the second part, performing several simulations, varying the features of the considered configuration, the stability is looked for. In order to perform this process, the Ansys Maxwell software has been used, performing 3D simulations.
Optimal control of the atmospheric arc of a space shuttle and numerical simulations with multiple-shooting method
2005
This article, continuation of previous works, presents the applications of geometric optimal control theory to the analysis of the Earth re-entry problem for a space shuttle where the control is the angle of bank, the cost is the total amount of thermal flux, and the system is subject to state constraints on the thermal flux, the normal acceleration and the dynamic pressure. Our analysis is based on the evaluation of the reachable set using the maximum principle and direct computations with the boundary conditions according to the CNES research project\footnote{The project is partially supported by the Centre National d'Etude Spatiales.}. The optimal solution is approximated by a concatenat…
Optimal control of an ensemble of Bloch equations with applications in MRI
2016
International audience; The optimal control of an ensemble of Bloch equations describing the evolution of an ensemble of spins is the mathematical model used in Nuclear Resonance Imaging and the associated costs lead to consider Mayer optimal control problems. The Maximum Principle allows to parameterize the optimal control and the dynamics is analyzed in the framework of geometric optimal control. This lead to numerical implementations or suboptimal controls using averaging principle.
Discrete and differential homotopy in circular restricted three-body control
2010
The planar circular restricted three-body problem is considered. The control enters linearly in the equation of motion to model the thrust of the third body. The minimum time optimal control problem has two scalar parameters: The ratio of the primaries masses which embeds the two-body problem into the three-body one, and the upper bound on the control norm. Regular extremals of the maximum principle are computed by shooting thanks to continuations with respect to both parameters. Discrete and dierential homotopy are compared in connection with second order sucient conditions in optimal control. Homotopy with respect to control bound gives evidence of various topological structures of extr…