Search results for "medium"
showing 10 items of 3746 documents
Raman Spectroscopic Fingerprints of Atomically Precise Ligand Protected Noble Metal Clusters: Au 38 (PET) 24 and Au 38− x Ag x (PET) 24
2021
Distinct Raman spectroscopic signatures of the metal core of atomically precise, ligand-protected noble metal nanoclusters are reported using Au38 (PET)24 and Au38- x Agx (PET)24 (PET = 2-phenylethanethiolate, -SC2 H4 C6 H5 ) as model systems. The fingerprint Raman features (occurring <200 cm-1 ) of these clusters arise due to the vibrations involving metal atoms of their Au23 or Au23- x Agx cores. A distinct core breathing vibrational mode of the Au23 core has been observed at 90 cm-1 . Whereas the breathing mode shifts to higher frequencies with increasing Ag content of the cluster, the vibrational signatures due to the outer metal-ligand staple motifs (between 200 and 500 cm-1 ) do not s…
Photo-induced electron transfer at nanostructured semiconductor–zinc porphyrin interface
2014
Abstract Electron transfer at metal oxide–organic dye interface on ZnO nanorod (ZnOr) templates was studied by femtosecond absorption spectroscopy method. Further confirmation of the electron transfer was obtained from photoelectrical studies. The fastest electron transfer from zinc porphyrin (ZnP) to semiconductor was observed for ZnOr modified by a 5 nm layer of TiO2 (
Grain size effect and local disorder in polycrystalline relaxors via scanning probe microscopy
2007
Local piezoresponse of individual grains in polycrystalline Pb0.9125La0.0975(Zr0.65Ti0.35)0.976O3 (PLZT 9.75/65/35) relaxor ceramics is studied using the scanning probe microscopy (SPM) technique. The observed piezoelectric contrast consisting of irregular (labyrinth-type) polarization patterns is attributed to the compositional disorder and consequent charge imbalance caused by high La concentration. A measure of this disorder, the polarization correlation length ξ, is directly determined using an autocorrelation analysis function implemented in the SPM software. The analysis of the obtained images shows that ξ taken at the scale ~200 nm varies as a function of the position inside the grai…
A stochastic shape and orientation model for fibres with an application to carbon nanotubes
2012
Methods are introduced for analysing the shape and orientation of planar fibres from greyscale images of fibrous systems. The sequence of image processing techniques needed for segmentation of fibres is described. The identified fibres were interpreted as deformed line segments for which two shape and two orientation parameters are estimated by the maximum likelihood method. The methods introduced are shown to perform quite well for simulated systems of deformed line segments with known properties. They were applied to TEM images of carbon nanotubes embedded in polycarbonate.
Acoustics of porous materials with partially opened porosity
2013
International audience; A theoretical and experimental study of the acoustic properties of porous materials containing dead-end (or partially opened) porosity was recently proposed by Dupont et al. The present article provides a description of partially opened porosity systems and their numerous potential applications in the general context of the study of porous materials, the classical models describing them, and the characterization techniques. It is shown that the dead-end pore effect can be treated independently and that the description of this effect can be associated with any acoustic model of porous media. Different theoretical developments describing the dead-end porosity effect ar…
Non-radiative recombination centres in catalyst-free ZnO nanorods grown by atmospheric-metal organic chemical vapour deposition
2013
We have investigated the cathodoluminescence (CL) emission and the Raman spectra along individual ZnO nanorods grown by a catalyst-free method. The spatial correlation between the CL emission and the defect related Raman modes permits establishing a correspondence between the non-radiative recombination centres (NRRCs) and the defects responsible for the 275 cm−1 Raman band. According to this relation, the NRRCs in these nanorods are tentatively associated with complexes of zinc interstitials.
Cladding-Pumped Erbium/Ytterbium Co-Doped Fiber Amplifier for C-Band Operation in Optical Networks
2021
Space-division multiplexing (SDM) attracts attention to cladding-pumped optical amplifiers, but they suffer from a low pump power conversion efficiency. To address this issue, ytterbium (Yb3+) and erbium (Er3+) co-doping is considered as an effective approach. However, it changes the gain profile of Er3+-doped fiber amplifiers and induces the gain difference between optical wavelengths in the C-band, significantly limiting the effective band of the dense wavelength-division multiplexed (DWDM) system. This paper is devoted to a detailed study of a cladding-pumped Er3+/Yb3+ co-doped fiber amplifier (EYDFA) through numerical simulations aiming to identify a configuration, before assembling a s…
Mechanical behaviour and failure modes of metal to composite adhesive joints for nautical applications
2010
In this paper, the influence of several parameters on the mechanical behaviour and failure modes of hybrid bonded joints aluminium/composite was investigated. Particularly, the effects of metallic surface condition, adhesive properties and thickness on single-lap joint resistance were analysed. To these aims, two adhesives were used and, for each adhesive, two different adhesive thicknesses (0.5 and 1.5 mm) have been investigated. Furthermore, two sets of joints for each adhesive kind and thickness were investigated: the former was obtained using aluminium blanks which were previously mechanically treated with sandpaper (P60) and the latter using aluminium treated with sandpaper and with pr…
Effect of Chemical Etching on Adhesively Bonded Aluminum AA6082
2007
The efforts of new automotive industry are mainly directed towards the substitution of aluminum for steel in the body structure because the aluminum structures are lighter than traditional steel ones and meet the requirements, in terms of both vehicle design and manufacture. However, this substitution is not so automatic, but it is important to study the material properties and the structure design, focusing the attention on the methods of joining. Welding, typical technique to joint steel parts, is particularly difficult when applied on aluminum ones and then, in many cases, the adhesive bonding is preferred. To optimise the joint performances it is necessary to pre-treat the metal surface…
A shear test for structural adhesives used in the consolidation of old timber
2001
A test method was developed specifically for structural adhesives used in thick joints. It is based on compressive shear loading of glued joints (GJ) and solid wood (SW) specimens, before and after a suitable accelerated ageing cycle. The evaluation of results is based on the ratios of wet strength to dry strength and on the comparison of GJ specimens to SW specimens which are prepared from the same batch of wood, in order to minimise the influence of the variability in wood characteristics. On a group of 10 epoxy-based adhesives, specifically marketed for the consolidation of old timber structures, the method has proved to be effective to differentiate the performances of each product. Amo…