Search results for "modular design"
showing 10 items of 139 documents
An AER handshake-less modular infrastructure PCB with x8 2.5Gbps LVDS serial links
2014
Nowadays spike-based brain processing emulation is taking off. Several EU and others worldwide projects are demonstrating this, like SpiNNaker, BrainScaleS, FACETS, or NeuroGrid. The larger the brain process emulation on silicon is, the higher the communication performance of the hosting platforms has to be. Many times the bottleneck of these system implementations is not on the performance inside a chip or a board, but in the communication between boards. This paper describes a novel modular Address-Event-Representation (AER) FPGA-based (Spartan6) infrastructure PCB (the AER-Node board) with 2.5Gbps LVDS high speed serial links over SATA cables that offers a peak performance of 32-bit 62.5…
Modular, customisable, accomodation-friendly antenna system for satellite avionics: Development, prototyping and validation
2014
In the frame of ESA program AO/1- 6737/11/NL/MH, an innovative X-band antenna system for satellite avionics has been studied, demonstrated and validated at Proof of Concept Model level. The innovative contribution of such an antenna system relies on modularity, customizability and accommodation friendliness. The antenna concept is based on a Plug and Play architecture, where the basic module is a 2.7 cm-cube with a mass of 53 gr, which can be clustered in array configuration. A catalogue of predefined and ready-to-use clusters could be developed with the possibility of adapting the antenna systems to various platform types by tuning just a few control parameters. Different levels of customi…
5-axes modular CNC machining center
2017
The paper presents the development of a 5-axes CNC machining center. The main goal of the machine was to provide the students a practical layout for training in advanced CAM techniques. The mechanical structure of the machine was built in a modular way by a specialized company, which also implemented the CNC controller. The authors of this paper developed the geometric and kinematic model of the CNC machining center and the post-processor, in order to use the machine in a CAM environment.
Modular fault diagnosis based on discrete event systems for a mixer chemical process
2003
The knowledge of failure type and their location is an indispensable requirement for the establishment of tasks of adequate recovery strategies and maintenance of both factory automation and process control systems. The failure diagnosis methodology presented in the paper is based on discrete event systems models and on the diagnosers concept, those which permit the analysis off-line and online of diagnosability of failures that can occur in the processes. We present an approach for models and associated diagnosers based on a modular decomposition of the global system, with the purpose of avoiding the problems of the exponential explosion of the number of states and of the computational com…
Modular device for determining forming limit curves – a cost effective aproach
2010
Abstract The paper presents the realising and functioning of a modular device for testing the formability of metal sheets. By using the device it is possible to realise experimentally the tests needed for drawing the forming limit curves using the Nakajima and Marciniak methods, but there can be also done researchs on deep-drawing. The results gathered from the tests were validated by numerical simulations using the finite element method. The device was designed at the Research Center for Metal Forming of the “Lucian Blaga” University of Sibiu and realised with the support of S.C. Uzina Mecanica Marsa – Sibiu
Steady State and Dynamic Models of Multistage Flash Desalination: A Review
2010
This article focuses on a review of literature studies on steady state and dynamic modeling of the multistage flash desalination process (MSF). The review shows that both steady state and dynamic models are based on lumped parameter approach. Differences in literature models are found in the assumptions used to model the flashing stage in addition to the correlations used to determine the heat transfer coefficients, thermodynamic losses, thermodynamic and transport properties. Interestingly, literature indicates a rapid progress made in software used for coding and solution of the model equations. The review shows a limited number of literature models for the internals of the flashing stage…
Active power maximizing for Wind Electrical Energy Generating Systems moved by a Modular Multiple Blade Fixed Pitch Wind Turbine
2008
This paper proposes a new solution for wind electrical energy generating system (WEEGS). The system here taken into account is moved by a modular multiple blade fixed pitch wind turbine (MMBFPWT) and foresees a new MPPT algorithm whose main characteristics are low cost, low noise, buildings simplicity and modularity. The mathematical model of the entire WEEGS has been here developed taking into account all the components starting from the wind turbine and ending with the electrical grid. The WEEGS mathematical model has been implemented in Matlab-Simulink in order to carry out the simulations needed to test the effectiveness of the proposed WEEGS. The simulations results show the effectiven…
UPS fuel cell based: An innovative back-up system
2007
The aim of the paper is to evaluate the technical feasibility and aspects related to the use, in an Uninterruptible Power Supply (UPS), of fuel cells instead of traditional electrochemical batteries. The proposed system, named UPS-FCB (Fuel Cell Based) presents a modular and versatile system configuration; particularly it is possible to integrate it with traditional UPS. Moreover the system features can be modified in terms of power, reliability, back-up time, etc., by changing the power devices. A detailed experimental analysis has been carried out on a passive stand-by UPS integrated with a FCB; experimental results can be easily extended to the other possible system architectures. © 2007…
Production planning in reconfigurable enterprises and reconfigurable production systems
2005
Reconfigurable enterprises and reconfigurable production systems represent nowadays one of the key responses towards the organisational and manufacturing needs arising in the new era known as mass customization. The paper proposes an Agent Based approach for the production planning activities in reconfigurable enterprises, characterized by complex, articulated and geographically distributed production capacities contended by many product families and composed by reconfigurable production systems that allow quick adjustment of production capacity and functionality consenting to manufacture different products of the same part family.
Analyses of the OSU-MASLWR Experimental Test Facility
2012
Today, considering the sustainability of the nuclear technology in the energy mix policy of developing and developed countries, the international community starts the development of new advanced reactor designs. In this framework, Oregon State University (OSU) has constructed, a system level test facility to examine natural circulation phenomena of importance to multi-application small light water reactor (MASLWR) design, a small modular pressurized water reactor (PWR), relying on natural circulation during both steady-state and transient operation. The target of this paper is to give a review of the main characteristics of the experimental facility, to analyse the main phenomena characteri…