Search results for "pellets"
showing 10 items of 67 documents
Direct determination by portable ED-XRF of mineral profile in cocoa powder samples
2019
Abstract The present study has exploited the rapidity of the analysis and the multi-elemental capability of the energy dispersive X- ray fluorescence (ED-XRF) technique for the mineral profile determination in cocoa powder. A fast, cheap and environmental sustainable method without reagent consumption or toxic waste generation has been proposed. The samples can be prepared in the form of pellets of 13 mm in diameter and 2–3 mm thickness. The different internal calibrations used by ED-XRF equipment did not provide accurate results when comparing the mineral profile with the concentration obtained by Inductively Couple Plasma Optical Emission Spectroscopy (ICP-OES) after microwave assisted di…
Properties of spark plasma sintered nanostructured Zn1+xSb
2011
Engineering materials with specific physical properties has recently focused on the effect of nanoscopic inhomogeneities at the 10 nm scale. Such features are expected to scatter medium and long-wavelength phonons lowering thereby the thermal conductivity of the system without simultaneously decreasing the charge transport (phonon–glass electron–crystal concept). A new Zn1+xSb nanophase obtained by a wet chemical approach was densified by spark plasma sintering (SPS). Investigations on compounds subsumed as “Zn4Sb3” always suffer from its low thermal stability and the contamination of the nanoparticles with solvents and additives used in the synthesis. In order to gain insight into this com…
Semi-continuous feeding and gasification of alfalfa and wheat straw pellets in a lab-scale fluidized bed reactor
2015
Abstract Small scale air-blown fluidized bed gasification of alfalfa and wheat straw pellets were conducted for semi-continuous solid feeding and range of operating conditions varied due to the modifications in equivalence ratio (ER) (0.20–0.35) achieved both by varying solid and air input. Alfalfa pellets displayed an improvement in several gasification variables such as gas lower heating value (∼4.1 MJ/Nm3), specific gas yield (1.66 Nm3/kg), cold gas efficiency (∼42%) and carbon conversion efficiency (∼72%) as ER maximized to 0.35 which was found optimum for this feedstock for the present course of experiments. Gasification parameters of wheat straw pellets on the other hand were characte…
Influence of electric field on thermo-chemical conversion of mixtures of straw pellets with coal
2018
Considerations on factors affecting biochar densification behavior based on a multiparameter model
2021
The optimization of upscaled biochar pelleting is limited by lack of knowledge regarding the effects of process parameters. A multiparameter model, coupled to a single pellet press unit, was for the first time applied to biochar production to predict the upscaled biochar pelleting process behavior. The model permits to estimate in a time and cost-effective way how the die friction forces, quantified through the pellet exiting pressure, are affected by the key process parameters. It was observed that to achieve acceptably low exiting pressures (in the order of 100 MPa), it was critical to produce biochar at high temperatures (e.g. 600 °C). Addition of water as a binder is also beneficial, wh…
Mechanical and barrier properties of extruded film made from sodium and calcium caseinates
2014
Abstract Over the past few years, much interest has been placed into the investigation of increased barrier and mechanical properties of protein films via a multitude of approaches. Generally, these techniques involve modifications of interactions among protein molecules, such as ionic crosslinking using divalent ions. To evaluate the crosslinking effect of Ca 2+ cations, films were made from calcium caseinate (CaCAS) and/or sodium caseinate (NaCAS). The production of caseinate thin films was carried out in two steps: first thermoplastic pellets were made using a co-rotating twin-screw extruder, then they were transformed into thin films (60 μm) using a classical film blowing machine. Tensi…
The Influence of The Degree of Grinding to Obtain of Some Fermented Mashes Based on Whole Wheat and Husked Millet
2011
The purpose of this article was to study the influence of degree of milling whole wheat (was ground in 4 variants of grain) and husked millet (was finely ground) to obtain fermented mashes type Braga. There have been 4 mashes of grist of whole wheat, grist husked millet, hop pellets and water and were boiled under continuous stirring and then cooled. Their content has diluted with water and then strainer by pressed through a sieve. Each mash-filtrate has divided in two and added white sugar 7%, resulting two series of sweet mashes. One has inoculated with a mixed culture of yeast and lactic bacteria and the other only with yeast culture. After fermentation were analyzed fermented mashes (pH…
Analytical Study of Raw Materials of Zinc Oxide Used for Enamels on Industrial Ceramics: Quantitative Analysis of Zinc, Lead, and Sulfur in These Sam…
2006
Abstract An analytical study is carried out to optimize X‐ray fluorescence (XRF) and flame atomic absorption spectrometry (FAAS) quantitative analysis of Zn, Pb, and S in ZnO samples commonly used to obtain industrial ceramic enamels. Pb and S in the raw materials often contaminate ZnO and are very detrimental in industrial applications. Thus, very accurate analytical determination of these elements in ceramic samples is extremely important. First of all, a mineralogical study by X‐ray diffraction (XRD) on the different components in these raw materials and the materials produced during the firing process is performed in order to establish the mineral forms in a reference sample for analysi…
Volatile compounds extracted from polypropylene sheets by hot water :influence of the temperature of sheets injection
1993
A study was made on polypropylene (PP) pellets degraded and not degraded and pointed out the presence and olfactive importance of volatile components extracted from PP pellets by hot water. Plastic packaging materials correspond to a further step of manufacturing: the injection step, and this is often conducted at high temperature. PP (not degraded) and PP-CR (degraded) were transformed into sheets at several temperatures; Lickens-Nickerson extracts were made and allowed the quantification of volatile compounds already identified. A statistical analysis showed that temperature was a very significant parameter. An increasing injection temperature (275 or 300°C° creates increasing quantities …