Search results for "polyamide"

1981

Polyamides 3 containing constant and definite numbers of oxyethylene units were prepared by condensation polymerization of suitable diamines and diesters, both of which containing oxyethylene units. The polymer structure was determined by IR and 1H NMR spectroscopy. Almost all polymers are crystals melting at ≈ 40°C and show a complexation ability towards alkalimetal cations. It was also found that diesters containing oxyethylene units show a higher condensation rate than alkylene diesters, which is explained by an inductive effect of the ether oxygene. However, no remarkable difference in the condensation rate was found between diamines containing oxyethylene units and the corresponding al…

1967

Optically active polyamides with regular structural sequences have been prepared from L-lysine and adipic acid. A novel optically active symmetrical diamine, N.N'-bis(L-5-amino-5-carboxyl-amyl)adipamide, was obtained by treating L-lysine with adipyl chloride in the presence of copper(II) ions. The interfacial polycondensation of this diamine with adipyl chloride afforded a regular polymer, while the polycondensation of L-lysine with adipyl chloride gave an irregular polymer of the same analytical composition. The melting points, optical rotations and the optical rotatory dispersions of these polymers were investigated. Optisch aktive Polyamide mit regelmasiger Struktur wurden aus L-Lysin un…

High performance PA6/CNTs nanohybrid fibers prepared in the melt

2012

Commercial and home-made carbon nanotubes (CNTs) were plasma treated under oxygen atmosphere and then added to polyamide 6 (PA6) in order to prepare fibres by melt spinning. For comparison, pristine nanofillers were used too. The effect of functionalization and of filler characteristics on the morphological, rheological, mechanical and electrical properties of the fibres was studied by TEM and SEM, rheological measurements, tensile and electrical conductivity tests. The results demonstrated that the functionalization led to a better mechanical performance and the morphological analysis confirmed that the adhesion, the dispersion and the alignment of the nanotubes within the polymer matrix w…

1983

Introduction des groupes alkyl dans le polyamide commercial Trogamid T. Formation d'anions polyamides par l'hydrure de sodium puis alkylation par les bromures d'alkyle

Recycling of dry and wet polyamide 6

2002

Recycling of polycondensation polymers can give rise to secondary materials with good mechanical properties only if a careful drying is carried out before the melt reprocessing operations. The presence of humidity provokes the hydrolytic chain scission of the macromolecules and the consequent decrease of molecular weight and properties. In this work, the drying step was substituted by the addition of an antioxidant that is able to protect the macromolecules because it is the autioxidant is more prone to hydrolysis, thus removing the water from the melt. The mechanical properties of polyamide 6 reprocessed more times in wet conditions and in the presence of this stabilizer are even better th…

Self-organized nanostructures of poly(4-vinylpyridine), polyaniline and polyamides due to metal complexation

2002

Comb-shaped supramolecules are constructed using flexible polymers and semi-rigid conjugated undoped or doped conjugated polymers upon complexing Zinc dodecyl benzene sulphonate, Zn(DBS) 2 . Self-organized nanostructures are formed in the bulk due to competing attractive interactions (coordination or water mediated hydrogen bonding) and repulsive polar/nonpolar interactions, showing characteristic long periods of ca. 30 A.

1991

The sanidic polyamide [NM-Ph(CO 2 R) 3 (CO 2 Me)-NMCO-Ph(OR) 2 CO] n (R=C 12 H 25 ) is studied. It is shown that this polymer has a biaxial structure with quasi 2-D long range translational correlations. The correlations in one direction are limited by the length of the molecule. The oriented regions are separated by regions in which the molecules are less oriented

Effect of compatibilization on the photo-oxidation behaviour of polyethylene/polyamide 6 blends and their nanocomposites

2015

Abstract Polymer based nanocomposites are increasingly attracting interest from academia and industry, and the use of polymer blends as matrices greatly increase their potential field of application. In order to improve their characteristics, the use of compatibilizers acting on the blend components is mandatory. However, this also leads to rising concerns regarding the behaviour of polymer blend based nanocomposites upon being subjected to photo-oxidative degradation. It is known that morphology can deeply influence the photo-oxidative behaviour, and this can be therefore deeply influenced by the blend components and by the use of compatibilizers. In this work, polymer blend nanocomposites…

Time-resolved rheology as a tool to monitor the progress of polymer degradation in the melt state – Part II: Thermal and thermo-oxidative degradation…

2015

Abstract Thermal and thermo-oxidative degradation of nanocomposites based on polyamide 11 (PA11) and organo-modified clay (Cloisite® 30B) are studied in the melt state (T = 215 °C) via time-resolved mechanical spectroscopy (TRMS). The goal is assessing the potentiality of rheological analysis for studying polymer degradation in complex systems such as polymer nanocomposites, whose rheological response stems from the combination of the contributions of polymer and nanoparticles. We prove that a thorough analysis grounded on TRMS allows to isolate the effect of degradation of the polymer matrix, whose progress can be hence profitably monitored. Essentially the same degradation mechanisms as i…

Compatibilization of polyethylene/polyamide 6 blend nanocomposite films

2015

Polymer blends of incompatible components need to undergo compatibilization, in order to give rise to a blend with good physical properties. At the same way, polymer/clay nanocomposites show this problem because of different chemical nature of the polymer matrix and of the clay. Compatibilization is therefore more necessary if an incompatible polymer blend is filled with an organomodified clay in order to give a final material with good properties. In this work, a polyethylene/polyamide 6 blend filled with an organomodified clay has been compatibilized with a maleic anhydride grafted SEBS (styrene-ethylene-butylene-styrene) copolymer and a glicidylmethacrylate-ethylene copolymer. The result…