Search results for "polystyrene"

1976

The phenomenon of “true cosolvency”, which has only recently been observed in the system acetone/diethyl ether/polystyrene (AC/DEE/PS), is investigated with regard to its pressure dependence and compared with the thermodynamic behaviour of the corresponding binary sub-systems. For the determination of the limits of complete solubility, a pressure apparatus was used which had been constructed, in order to measure the turbidity of fluids in the temperature range of −70 to +500°Cand in the pressure range of 1 to 4000 bar (105 to 4·108 Nm−2). The critical line observed for the system DEE/PS (MPS=20400) looks similar to that reported for AC/PS in the literature, i.e. the upper critical solution …

ChemInform Abstract: Hydrophobically Directed Aldol Reactions: Polystyrene-Supported L-Proline as a Recyclable Catalyst for Direct Asymmetric Aldol R…

2008

A simple synthetic methodology for the preparation of a polystyrene-supported L-proline material is reported, and this material has been used as catalyst in direct asymmetric aldol reactions between several ketones and arylaldehydes to furnish aldol products in high yields and stereoselectivities. Screening of solvents showed that these reactions take place only in the presence of water or methanol, at lower levels of conversion in the latter case. This solvent effect, coupled with the observed high stereoselectivities, has been explained in terms of the formation of a hydrophobic core in the inner surface of the resin, whereas the hydrophilic proline moiety lies at the resin/water interfac…

Azoxybenzene rearrangement catalyzed by solid acids

2008

Abstract For the first time, the potential of acidic cation-exchange resin (sulfonated polystyrene) to catalyze the Wallach rearrangement of azoxybenzene into 4-hydroxyazobenzene has been proved. This finding reveals an alternative reaction path possible in a heterogeneous process using solid acids and may help to clear some doubts concerning the rearrangement mechanism postulated so far. The resin-induced reaction was found to proceed exclusively in a non-polar medium. Reasonable yield was obtained particularly in isooctane due to favorable distribution of azoxybenzene throughout the resin's matrix. On the contrary, the HY type zeolite did not activate the rearrangement, most probably beca…

Controlled radical polymerization of alkyl acrylates and styrene using a half-sandwich molybdenum(III) complex containing diazadiene ligands

2003

Abstract The half-sandwich molybdenum(III) complex CpMoCl 2 ( i Pr 2 -dad) ( i Pr 2 -dad= i Pr–NCH–CHN– i Pr) proved to be an effective metal catalyst for the controlled radical polymerization of methyl acrylate, butyl acrylate, and styrene. In conjunction with an alkyl iodide [R–I: CH 3 CH(COOEt)I] as an initiator and in the presence or absence of Al(O– i -Pr) 3 as a co-catalyst, the molybdenum-based system gave polymers with narrow molecular weight distributions. The in situ addition of styrene to a macroinitiator of poly(methylacrylate) afforded an AB-type block copolymer.

Micromechanics of “raspberry” morphology in PPE/SAN polymer blends compatibilized with linear ABC triblock terpolymers

2015

Abstract The effect of compatibilization with a symmetrical polystyrene- block -polybutadiene- block -poly(methyl methacrylate) (SBM) triblock terpolymer on the morphological and mechanical properties (specifically toughness) of immiscible poly(2,6-dimethyl-1,4-phenylene ether)/poly(styrene- co -acrylonitrile) (PPE/SAN) blends with different blend (w/w) ratios is investigated. We study the effect of blend viscosity on the localization of the compatibilizer at the blend interface, influencing the mechanical properties of the macroscopic material. The impact of the specific morphology of the blends, known as “raspberry morphology”, on the final material will be explained using thermomechanica…

Modelling the Influence of Nanoparticles in the Phase Behaviour of an Epoxy/Polystyrene Mixture, 2

2007

The influences of nanoparticle size and concentration on the thermodynamic behaviour of epoxy/polystyrene blends are evaluated in the framework of Ginzburg's simple analytical theory. Two approaches have been employed: NPEPO (for particles coated with epoxy groups) and NPFEN (for particles coated with phenyl groups). Using NPEPO, the particles are found to prefer the phase richer in epoxy, whereas the opposite occurs for NPFEN. The particles size significantly influences blend compatibility. When the particle radius Rp is about the same size as the radius of gyration R g of PS, the compatibility of blends increases with particle concentration, whereas for R p > R g , higher particle concent…

1980

Molecular weights of Trogamid T® were determined by ultracentrifugation, light-scattering, osmometry and viscometry, molecular weight distributions by gel permeation chromatography (GPC) and five different fractionation methods. The separation efficiency of GPC with N,N-dimethylformamide as solvent was tested with three different types of gels, crosslinked polystyrene, porous glass and crosslinked poly(vinyl acetate), the last one yielding the best results. Solution fractionations show better results than precipitation methods. All fractionations gave far too small apparent non-uniformities. After correction according to the non-uniformities of the fractions the results corresponded to thos…

Polymer induced changes of the crystallization scenario in suspensions of hard sphere like microgel particles

2012

We investigated the crystallization scenario of highly cross linked polystyrene particles dispersed in the good solvent 2-ethylnaphtalene and their mixtures with non-adsorbing low molecular weight polysterene polymer using time resolved static light scattering. The samples were prepared slightly below the melting volume fraction of the polymer free system. For the polymer free samples, we obtained polycrystalline solids via crystallization scenario known from hard sphere suspensions with little competition of wall crystal formation. Addition of non-adsorbing low molecular weight polystyrene polymer leads to a considerably slowing down of the bulk crystallization kinetics. We observed a dela…

A contribution to the kinetics of the polymerization of styrene with CF3SO3H as catalyst

1978

The time dependence of the cationic polymerization of styrene in CH2Cl2 with CF3SO3H as catalyst can be formally described as being first-order with respect to monomer concentration [M]0. The reaction rate shows a third-order dependence in catalyst concentration [C]0. A high polymer and a low polymer polystyrene fraction are found at [M]0>0.2 mole · l−. The reaction rate of the high polymer fraction is proportional to [C] 0 3 , that of the low polymer fraction probably proportional to [C] 0 2 . The polymerization active species may thus be triple ions in the first and ion pairs in the second case.

2018

We report a novel multi-step method for the preparation of ordered mesoporous titania scaffolds and show an illustrative example of their application to solar cells. The method is based on (monolayer) colloidal nanosphere lithography that makes use of polystyrene nanoparticles organised at a water–air interface and subsequently transferred onto a solid substrate. A titania precursor solution (titanium(IV) isopropoxide in ethanol) is then drop-cast onto the monolayer and left to “incubate” overnight. Surprisingly, instead of the expected inverse monolayer-structure, a subsequent calcination step of the precursor yields an ordered monolayer of hollow titania nanospheres with a wall thickness …